Searcharxiv⌕ Search
Home/Archive/arXiv

arXiv · 2605.07311

A Microfabricated PCM-Switched Reconfigurable Intelligent Surface for Wideband Millimeter-Wave Beam Steering

Afsaneh Hojjati-Firoozabadi·Raafat Mansour
View original source ↗Read source document ↗Export metadata ↓

Abstract

This paper presents the design, fabrication, and experimental validation of a reconfigurable intelligent surface (RIS) employing electrically actuated vanadium dioxide (VO2) switches for millimeter wave beam steering. The proposed RIS is realized using a multilayer microfabrication process on an alumina substrate, enabling monolithic integration of hundreds of sub-4 micrometer VO2 switching elements within deeply subwavelength unit cells, approximately one-fifth of the wavelength. The switching-induced modulation of surface impedance is analyzed through full-wave simulations, and the resulting phase and amplitude responses are experimentally characterized using a custom WR-28 waveguide measurement setup. Based on the validated unit-cell design, a 10 x 20 RIS array integrating 200 VO2 switches is fabricated. The switches within each column are serially biased using integrated routing lines, allowing programmable control of the spatial phase distribution across the surface. Synthesized phase profiles enable dynamic beam steering, resulting in measured far-field gain enhancement of 10-20 dB over an 18 percent fractional bandwidth centered at 33 GHz, with steering angles up to 60 degrees. The measured radiation patterns are in good agreement with semi-numerical channel modeling predictions. By combining thin-film PCM switching with an integration-aware unit-cell design, this work demonstrates a scalable RIS architecture that mitigates packaging parasitics and footprint limitations inherent to conventional semiconductor-based implementations, providing a practical pathway toward higher-frequency reconfigurable surfaces.

Explore related subjects

eess.SP

Keep this discovery

BibTeXRIS

Afsaneh Hojjati-Firoozabadi, Raafat Mansour. 2026-05-08. A Microfabricated PCM-Switched Reconfigurable Intelligent Surface for Wideband Millimeter-Wave Beam Steering. https://arxiv.org/abs/2605.07311

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related papers

arXiv2026

Load Balancing in Multi-Shell LEO Satellite Networks with Successive Interference Cancellation

Multi-shell low Earth orbit (LEO) networks can increase service opportunities, but altitude-dependent propagation can concentrate traffic on lower shells and create strong inter-shell interference under full frequency reuse. This paper develops a mathematical framework for load balancing in multi-shell LEO satellite networks. Satellites on each shell form an independent spherical Poisson point process (SPPP), and the typical user associates with one of the per-shell serving satellites through a shell-dependent biased received-power rule, with receiver-side successive interference cancellation (SIC) under full frequency reuse. Shell-wise association probabilities, conditioned serving-distance distributions, and the rate coverage probability under shell-dependent traffic loads are derived and validated by simulation. The results show that shell-dependent biasing alleviates lower-shell traffic concentration and improves rate coverage, while receiver-side SIC mitigates the dominant lower-shell interference experienced by users associated with upper shells. Load balancing provides its largest rate-coverage gain in traffic hotspots, while SIC becomes more valuable as receive-side isolation weakens. With a fixed satellite budget, distributing satellites across multiple shells can further improve hotspot rate coverage by adding shell-wise serving opportunities.

eess.SP↗
arXiv2026

Tensor Decomposition Based Mixed-Field Sensing for XL-MIMO AFDM Systems

Integrated sensing and communications enabled by extremely large-scale MIMO (XL-MIMO) and affine frequency division multiplexing (AFDM) is a highly promising paradigm for vehicular networks. However, the near-field spherical wavefront distortions induce severe non-linear parameter coupling, while the highly dynamic scattering environments exacerbate mismatch errors. To address these critical challenges, this paper proposes a novel tensor-based sensing scheme for XL-MIMO AFDM systems. First, the received signals are reformulated into a tensor, followed by an efficient decomposition approach that exploits the inherent Vandermonde structure of the factor matrices. This allows parameters to be directly estimated from the decomposed matrices, effectively avoiding inter-parameter coupling. Subsequently, a symmetric decoupling and real-domain manifold optimization algorithm is proposed for angle of arrival estimation, circumventing the high-dimensional searches typically induced by near-field effects. Furthermore, a baseband reconstruction and analytical gradient-based algorithm is developed to perform delay-Doppler estimation in the continuous parameter domain, fundamentally eradicating the grid-mismatch errors inherent in high-mobility scenarios. With these decoupled factors, the remaining unknown angle of departure can be readily extracted. Extensive simulation results demonstrate that the proposed scheme achieves orders-of-magnitude improvements in delay-Doppler accuracy and eliminates the error floors in angular estimation that severely bottleneck state-of-the-art baselines.

eess.SP↗
arXiv2026

Radio Map Construction with Post-Hoc Location Calibration under Quasi-Static Positioning Errors: Joint Estimation, Performance Bounds, and GNSS-Based Evaluation

Radio maps enable environment-aware wireless and Internet-of-Things applications and can be constructed from location-tagged received signal strength (RSS) measurements collected by mobile devices. In urban environments, temporally correlated GNSS errors can shift an entire sensing trajectory, causing systematic spatial misregistration that is not mitigated by collecting more measurements. This paper presents a radio-map construction framework that uses the radio measurements themselves to calibrate erroneous location tags after data collection. The dominant positioning error is modeled as a sensor-specific quasi-static offset, which is jointly estimated with radio-propagation parameters in a Gaussian process regression (GPR) framework by exploiting complementary spatial information from distance-dependent path loss and spatially correlated shadowing. We establish lower and upper bounds on the conditional Bayes risk and show that, under a translation-invariant trajectory model, trajectory information alone cannot identify the quasi-static offset, thereby motivating the use of RSS-derived spatial information for calibration. Numerical evaluations across propagation conditions show that the proposed method reduces the mean squared error (MSE) gap from ideal GPR to approximately $3.26\mathrm{dB}^2$, compared with about $10\mathrm{dB}^2$ for position-error-agnostic and noisy-input GPR baselines. Evaluation using positioning-error models derived from smartphone GNSS measurements shows that the proposed method outperforms a KF--RTS trajectory-smoothing baseline despite unmodeled time-varying positioning errors, remaining within approximately $5\mathrm{dB}^2$ of ideal GPR at the median MSE. These results demonstrate that RSS measurements can serve not only as observations for radio-map reconstruction but also as spatial cues for post-hoc calibration of imperfectly geotagged sensing data.

eess.SP↗