arXiv subjects

A. A. Balandin

Publications and source records attributed to A. A. Balandin.

At least 19 recordsLinked to original sources

arXiv2021

Depinning of the Charge-Density Waves in Quasi-2D 1T-TaS2 Devices Operating at Room Temperature

We report on depinning of nearly-commensurate charge-density waves in 1T-TaS2 thin-films at room temperature. A combination of the differential current-voltage measurements with the low-frequency noise spectroscopy provide unambiguous means for detecting the depinning threshold field in quasi-2D materials. The depinning process in 1T-TaS2 is not accompanied by an observable abrupt increase in electric current - in striking contrast to depinning in the conventional charge-density-wave materials with quasi-1D crystal structure. We explained it by the fact that the current density from the charge-density waves in the 1T-TaS2 devices is orders of magnitude smaller than the current density of the free carriers available in the discommensuration network surrounding the commensurate charge-density-wave islands. The depinning fields in 1T-TaS2 thin-film devices are several orders of magnitude larger than those in quasi-1D van der Waals materials. Obtained results are important for the proposed applications of the charge-density-wave devices in electronics.

cond-mat.mes-hall↗

arXiv2019

Electric Switching of the Charge-Density-Wave and Normal Metallic Phases in Tantalum Disulfide Thin-Film Devices

We report on switching among three charge-density-wave phases - commensurate, nearly commensurate, incommensurate - and the high-temperature normal metallic phase in thin-film 1T-TaS2 devices induced by application of an in-plane electric field. The electric switching among all phases has been achieved over a wide temperature range, from 77 K to 400 K. The low-frequency electronic noise spectroscopy has been used as an effective tool for monitoring the transitions, particularly the switching from the incommensurate charge-density-wave phase to the normal metal phase. The noise spectral density exhibits sharp increases at the phase transition points, which correspond to the step-like changes in resistivity. Assignment of the phases is consistent with low-field resistivity measurements over the temperature range from 77 K to 600 K. Analysis of the experimental data and calculations of heat dissipation suggest that Joule heating plays a dominant role in the electric-field induced transitions in the tested 1T-TaS2 devices on Si/SiO2 substrates. The possibility of electrical switching among four different phases of 1T-TaS2 is a promising step toward nanoscale device applications. The results also demonstrate the potential of noise spectroscopy for investigating and identifying phase transitions in materials.

physics.app-ph↗

arXiv2019

Proton-Irradiation-Immune Electronics Implemented with Two-Dimensional Charge-Density-Wave Devices

Proton radiation damage is an important failure mechanism for electronic devices in near-Earth orbits, deep space and high energy physics facilities. Protons can cause ionizing damage and atomic displacements, resulting in device degradation and malfunction. Shielding of electronics increases the weight and cost of the systems but does not eliminate destructive single events produced by energetic protons. Modern electronics based on semiconductors - even those specially designed for radiation hardness - remain highly susceptible to proton damage. Here we demonstrate that room temperature (RT) charge-density-wave (CDW) devices with quasi-two-dimensional (2D) 1T-TaS2 channels show remarkable immunity to bombardment with 1.8 MeV protons to a fluence of at least 10^14 H+cm^2. Current-voltage I-V characteristics of these 2D CDW devices do not change as a result of proton irradiation, in striking contrast to most conventional semiconductor devices or other 2D devices. Only negligible changes are found in the low-frequency noise spectra. The radiation immunity of these "all-metallic" CDW devices can be attributed to their two-terminal design, quasi-2D nature of the active channel, and high concentration of charge carriers in the utilized CDW phases. Such devices, capable of operating over a wide temperature range, can constitute a crucial segment of future electronics for space, particle accelerator and other radiation environments.

physics.app-ph↗

arXiv2018

The Discrete Noise of Magnons

Magnonics is a rapidly developing subfield of spintronics, which deals with devices and circuits that utilize spin currents carried by magnons - quanta of spin waves. Magnon current, i.e. spin waves, can be used for information processing, sensing, and other applications. A possibility of using the amplitude and phase of magnons for sending signals via electrical insulators creates conditions for avoiding Ohmic losses, and achieving ultra-low power dissipation. Most of the envisioned magnonic logic devices are based on spin wave interference, where the minimum energy per operation is limited by the noise level. The sensitivity and selectivity of magnonic sensors is also limited by the low frequency noise. However, the fundamental question "do magnons make noise?" has not been answered yet. It is not known how noisy magnonic devices are compared to their electronic counterparts. Here we show that the low-frequency noise of magnonic devices is dominated by the random telegraph signal noise rather than 1/f noise - a striking contrast to electronic devices (f is a frequency). We found that the noise level of surface magnons depends strongly on the power level, increasing sharply at the on-set of nonlinear dissipation. The presence of the random telegraph signal noise indicates that the current fluctuations involve random discrete macro events. We anticipate that our results will help in developing the next generation of magnonic devices for information processing and sensing.

cond-mat.mes-hall↗

arXiv2017

Total Ionizing Dose Effects on Threshold Switching in 1T-Tantalum Disulfide Charge-Density-Wave Devices

The 1T polytype of TaS2 exhibits voltage-triggered threshold switching as a result of a phase transition from nearly commensurate to incommensurate charge density wave states. Threshold switching, persistent above room temperature, can be utilized in a variety of electronic devices, e.g., voltage controlled oscillators. We evaluated the total-ionizing-dose response of thin film 1T-TaS2 at doses up to 1 Mrad(SiO2). The threshold voltage changed by less than 2% after irradiation, with persistent self-sustained oscillations observed through the full irradiation sequence. The radiation hardness is attributed to the high intrinsic carrier concentration of 1T-TaS2 in both of the phases that lead to threshold switching. These results suggest that charge density wave devices, implemented with thin films of 1T-TaS2, are promising for applications in high radiation environments.

physics.app-ph↗

arXiv2017

Spin - Phonon Coupling in Nickel Oxide Determined from Ultraviolet Raman Spectroscopy

Nickel oxide (NiO) has been studied extensively for various applications ranging from electrochemistry to solar cells [1,2]. In recent years, NiO attracted much attention as an antiferromagnetic (AF) insulator material for spintronic devices [3-10]. Understanding the spin - phonon coupling in NiO is a key to its functionalization, and enabling AF spintronics' promise of ultra-high-speed and low-power dissipation [11,12]. However, despite its status as an exemplary AF insulator and a benchmark material for the study of correlated electron systems, little is known about the spin - phonon interaction, and the associated energy dissipation channel, in NiO. In addition, there is a long-standing controversy over the large discrepancies between the experimental and theoretical values for the electron, phonon, and magnon energies in NiO [13-23]. This gap in knowledge is explained by NiO optical selection rules, high Neel temperature and dominance of the magnon band in the visible Raman spectrum, which precludes a conventional approach for investigating such interaction. Here we show that by using ultraviolet (UV) Raman spectroscopy one can extract the spin - phonon coupling coefficients in NiO. We established that unlike in other materials, the spins of Ni atoms interact more strongly with the longitudinal optical (LO) phonons than with the transverse optical (TO) phonons, and produce opposite effects on the phonon energies. The peculiarities of the spin - phonon coupling are consistent with the trends given by density functional theory calculations. The obtained results shed light on the nature of the spin - phonon coupling in AF insulators and may help in developing innovative spintronic devices.

cond-mat.mtrl-sci↗

arXiv2017

Inelastic Light Scattering Spectroscopy of Magnons and Phonons in Nickel Oxide: Effects of Temperature

We report results of an investigation of the temperature dependence of the magnon and phonon frequencies in NiO. A combination of Brillouin - Mandelstam and Raman spectroscopies allowed us to elucidate the evolution of the phonon and magnon spectral signatures from the Brillouin zone center (GHz range) to the second-order peaks from the zone boundary (THz range). The temperature-dependent behavior of the magnon and phonon bands in the NiO spectrum indicates the presence of antiferromagnetic (AF) order fluctuation or a persistent AF state at temperatures above the Neel temperature (T=523 K). Tuning the intensity of the excitation laser provides a method for disentangling the features of magnons from acoustic phonons without the application of a magnetic field. Our results are useful for interpretation of the inelastic-light scattering spectrum of NiO, and add to the knowledge of its magnon properties important for THz spintronic devices.

cond-mat.mtrl-sci↗

arXiv2016

Magnetic and Thermal Transport Properties of Permanent Magnets with Anisotropic Grain Structure

Nanostructured permanent magnets are gaining increasing interest and importance for applications such as generators and motors. Thermal management is a key concern since performance of permanent magnets decreases with temperature. We investigated the magnetic and thermal transport properties of rare-earth free nanostructured SrFe12O19 magnets produced by the current activated pressure assisted densification. The synthesized magnets have aligned grains such that their magnetic easy axis is perpendicular to their largest surface area to maximize their magnetic performance. The SrFe12O19 magnets have fine grain sizes in the cross-plane direction and substantially larger grain sizes in the in-plane direction. It was found that this microstructure results in approximately a factor of two higher thermal conductivity in the in-plane direction, providing an opportunity for effective cooling. The phonons are the dominant heat carriers in this type of permanent magnets near room temperature. Temperature and direction dependent thermal conductivity measurements indicate that both Umklapp and grain boundary scattering are important in the in-plane direction, where the characteristic grain size is relatively large, while grain boundary scattering dominates the cross-plane thermal transport. The investigated nano/microstructural design strategy should translate well to other material systems and thus have important implications for thermal management of nanostructured permanent magnets.

cond-mat.mtrl-sci↗

arXiv2016

Magnetometer Based On Spin Wave Interferometer

We describe magnetic field sensor based on spin wave interferometer. Its sensing element consists of a magnetic cross junction with four micro-antennas fabricated at the edges. Two of these antennas are used for spin wave excitation and two others antennas are used for the detection of the inductive voltage produced by the interfering spin waves. Two waves propagating in the orthogonal arms of the cross may accumulate significantly different phase shifts depending on the magnitude and the direction of the external magnetic field. This phenomenon is utilized for magnetic field sensing. The sensitivity has maximum at the destructive interference condition, where a small change of the external magnetic field results in a drastic increase of the inductive voltage as well as the change of the output phase. We report experimental data obtained on a micrometer scale Y3Fe2(FeO4)3 cross structure. The change of the inductive voltage near the destructive interference point exceeds 40 dB per 1 Oe. At the same time, the phase of the output exhibit a π-phase shift within 1 Oe. The data are collected for three different orientations of the sensor in magnetic field at room temperature. Taking into account low thermal noise in ferrite structures, the maximum sensitivity of spin wave magnetometer may exceed atta Tesla. Other appealing advantages include compactness, fast data acquisition and wide temperature operating range. The physical limits of spin wave interferometers are also discussed.

cond-mat.other↗

arXiv2016

Thermal and Magnetic Properties of Nanostructured Ferrimagnetic Composites with Graphene - Graphite Fillers

We report the results of an experimental study of thermal and magnetic properties of nanostructured ferrimagnetic iron oxide composites with graphene and graphite fillers synthesized via the current activated pressure assisted densification. The thermal conductivity was measured using the laser-flash and transient plane source techniques. It was demonstrated that addition of 5 wt. % of equal mixture of graphene and graphite flakes to the composite results in a factor of x2.6 enhancement of the thermal conductivity without significant degradation of the saturation magnetization. The microscopy and spectroscopic characterization reveal that sp2 carbon fillers preserve their crystal structure and morphology during the composite processing. The strong increase in the thermal conductivity was attributed to the excellent phonon heat conduction properties of graphene and graphite. The results are important for energy and electronic applications of the nanostructured permanent magnets.

cond-mat.mtrl-sci↗

arXiv2016

Graphene-Enhanced Thermal Interface Materials for Thermal Management of Photovoltaic Solar Cells

The increase in the temperature of photovoltaic (PV) solar cells affects negatively their power conversion efficiency and decreases their lifetime. The negative effects are particularly pronounced in concentrator solar cells. Therefore, it is crucial to limit the PV cell temperature by effectively removing the excess heat. Conventional thermal phase change materials (PCMs) and thermal interface materials (TIMs) do not possess the thermal conductivity values sufficient for thermal management of the next generation of PV cells. In this paper, we report the results of investigation of the increased efficiency of PV cells with the use of graphene-enhanced TIMs. Graphene reveals the highest values of the intrinsic thermal conductivity. It was also shown that the thermal conductivity of composites can be increased via utilization of graphene fillers. We prepared TIMs with up to 6% of graphene designed specifically for PV cell application. The solar cells were tested using the solar simulation module. It was found that the drop in the output voltage of the solar panel under two-sun concentrated illumination can be reduced from 19% to 6% when graphene-enhanced TIMs are used. The proposed method can recover up to 75% of the power loss in solar cells.

cond-mat.mtrl-sci↗

arXiv2016

Magnonic Interferometric Switch for Multi-Valued Logic Circuits

We investigated a possible use of the magnonic interferometric switches in multi-valued logic circuits. The switch is a three-terminal device consisting of two spin channels where input, control, and output signals are spin waves. Signal modulation is achieved via the interference between the source and gate spin waves. We report experimental data on a micrometer scale prototype based on Y3Fe2(FeO4)3 structure. The output characteristics are measured at different angles of the bias magnetic field. The On/Off ratio of the prototype exceeds 36 dB at room temperature. Experimental data is complemented by the theoretical analysis and the results of micro magnetic simulations showing spin wave propagation in a micrometer size magnetic junction. We also present the results of numerical modeling illustrating the operation of a nanometer-size switch consisting of just 20 spins in the source-drain channel. The utilization of spin wave interference as a switching mechanism makes it possible to build nanometer-scale logic gates, and minimize energy per operation, which is limited only by the noise margin. The utilization of phase in addition to amplitude for information encoding offers an innovative route towards multi-state logic circuits. We describe possible implementation of the three-value logic circuits based on the magnonic interferometric switches. The advantages and shortcomings inherent in interferometric switches are also discussed.

cond-mat.mes-hall↗

arXiv2015

Magnetically-Functionalized Self-Aligning Graphene Fillers for High-Efficiency Thermal Management Applications

We report on heat conduction properties of thermal interface materials with self-aligning "magnetic grapheme" fillers. Graphene enhanced nano-composites were synthesized by an inexpensive and scalable technique based on liquid-phase exfoliation. Functionalization of graphene and few-layer-graphene flakes with Fe3O4 nanoparticles allowed us to align the fillers in an external magnetic field during dispersion of the thermal paste to the connecting surfaces. The filler alignment results in a strong increase of the apparent thermal conductivity and thermal diffusivity through the layer of nano-composite inserted between two metallic surfaces. The self-aligning "magnetic grapheme" fillers improve heat conduction in composites with both curing and non-curing matrix materials. The thermal conductivity enhancement with the oriented fillers is a factor of two larger than that with the random fillers even at the low ~1 wt. % of graphene loading. The real-life testing with computer chips demonstrated the temperature rise decrease by as much as 10oC with use of the non-curing thermal interface material with ~1 wt. % of the oriented fillers. Our proof-of-concept experiments suggest that the thermal interface materials with functionalized graphene and few-layer-graphene fillers, which can be oriented during the composite application to the surfaces, can lead to a new method of thermal management of advanced electronics.

cond-mat.mtrl-sci↗

arXiv2015

Gas Sensing with h-BN Capped MoS2 Heterostructure Thin Film Transistors

We have demonstrated selective gas sensing with molybdenum disulfide (MoS2) thin films transistors capped with a thin layer of hexagonal boron nitride (h-BN). The resistance change was used as a sensing parameter to detect chemical vapors such as ethanol, acetonitrile, toluene, chloroform and methanol. It was found that h-BN dielectric passivation layer does not prevent gas detection via changes in the source-drain current in the active MoS2 thin film channel. The use of h-BN cap layers (thickness H=10 nm) in the design of MoS2 thin film gas sensors improves device stability and prevents device degradation due to environmental and chemical exposure. The obtained results are important for applications of van der Waals materials in chemical and biological sensing.

cond-mat.mes-hall↗

arXiv2015

Anisotropy of Thermal Conductivity of Free-Standing Reduced Graphene Oxide Films Annealed at High Temperature

We investigated thermal conductivity of free-standing reduced graphene oxide films subjected to a high-temperature treatment of up to 1000 C. It was found that the high-temperature annealing dramatically increased the in-plane thermal conductivity, K, of the films from 3 W/mK to 61 W/mK at room temperature. The cross-plane thermal conductivity, Kc, revealed an interesting opposite trend of decreasing to a very small value of 0.09 W/mK in the reduced graphene oxide films annealed at 1000 C. The obtained films demonstrated an exceptionally strong anisotropy of the thermal conductivity, K/Kc ~ 675, which is substantially larger even than in the high-quality graphite. The electrical resistivity of the annealed films reduced to 1 - 19 Ohms/sq. The observed modifications of the in-plane and cross-plane thermal conductivity components resulting in an unusual K/Kc anisotropy were explained theoretically. The theoretical analysis suggests that K can reach as high as ~500 W/mK with the increase in the sp2 domain size and further reduction of the oxygen content. The strongly anisotropic heat conduction properties of these films can be useful for applications in thermal management.

cond-mat.mtrl-sci↗

arXiv2015

The Commensurate-Incommensurate Charge-Density-Wave Transition and Phonon Zone Folding in 1T-TaSe2 Thin Films

Bulk 1T-TaSe2 exhibits unusually high charge density wave (CDW) transition temperatures of 600 K and 473 K below which the material exists in the incommensurate (I-CDW) and the commensurate (C-CDW) charge-density-wave phases, respectively. The C-CDW reconstruction of the lattice coincides with new Raman peaks resulting from zone-folding of phonon modes from middle regions of the original Brillouin zone back to the Gamma point. The C-CDW transition temperatures as a function of film thickness are determined from the evolution of these new Raman peaks and they are found to decrease from 473K to 413K as the film thicknesses decrease from 150 nm to 35 nm. A comparison of the Raman data with ab initio calculations of both the normal and C-CDW phases gives a consistent picture of the zone-folding of the phonon modes following lattice reconstruction. In the I-CDW phase, the loss of translational symmetry coincides with a strong suppression and broadening of the Raman peaks. The observed change in the C-CDW transition temperature is consistent with total energy calculations of bulk and monolayer 1T-TaSe2.

cond-mat.mes-hall↗

arXiv2015

Low-Frequency 1/f Noise in MoS2 Thin-Film Transistors: Comparison of Single and Multilayer Structures

We report on the transport and low-frequency noise measurements of MoS2 thin-film transistors with "thin" (2-3 atomic layers) and "thick" (15-18 atomic layers) channels. The back-gated transistors made with the relatively thick MoS2 channels have advantages of the higher electron mobility and lower noise level. The normalized noise spectral density of the low-frequency 1/f noise in "thick" MoS2 transistors is of the same level as that in graphene. The MoS2 transistors with the atomically thin channels have substantially higher noise levels. It was established that, unlike in graphene devices, the noise characteristics of MoS2 transistors with "thick" channels (15-18 atomic planes) could be described by the McWhorter model. Our results indicate that the channel thickness optimization is crucial for practical applications of MoS2 thin-film transistors.

cond-mat.mes-hall↗

arXiv2014

High-Temperature Performance of MoS2 Thin-Film Transistors: DC and Pulse Current-Voltage Characteristics

The measurements of the high - temperature current - voltage characteristics of MoS2 thin - film transistors show that the devices remain functional to temperatures of at least as high as 500 K. The temperature increase results in decreased threshold voltage and mobility. The comparison of the DC and pulse measurements shows that the DC sub - linear and super - linear output characteristics of MoS2 thin - films devices result from the Joule heating and the interplay of the threshold voltage and mobility temperature dependences. At temperatures above 450 K, an intriguing phenomenon of the "memory step" - a kink in the drain current - occurs at zero gate voltage irrespective of the threshold voltage value. The memory step effect was attributed to the slow relaxation processes in thin films similar to those in graphene and electron glasses. The obtained results suggest new applications for MoS2 thin - film transistors in extreme - temperature electronics and sensors.

cond-mat.mtrl-sci↗