arXiv subjects

A. Garson III

Publications and source records attributed to A. Garson III.

7 recordsLinked to original sources

arXiv2010

Scientific Prospects for Hard X-ray Polarimetry

X-ray polarimetry promises to give qualitatively new information about high-energy sources. Examples of interesting source classes are binary black hole systems, rotation and accretion powered neutron stars, Microquasars, Active Galactic Nuclei and Gamma-Ray Bursts. Furthermore, X-ray polarimetry affords the possibility for testing fundamental physics, e.g. to observe signatures of light bending in the strong gravitational field of a black hole, to detect third order Quantum Electrodynamic effects in the magnetosphere of Magnetars, and to perform sensitive tests of Lorentz Invariance. In this paper we discuss scientific drivers of hard (>10 keV) X-ray polarimetry emphasizing how observations in the hard band can complement observations at lower energies (0.1 - 10 keV). Subsequently, we describe four different technical realizations of hard X-ray polarimeters suitable for small to medium sized space borne missions, and study their performance in the signal-dominated case based on Monte Carlo simulations. We end with confronting the instrument requirements for accomplishing the science goals with the capabilities of the four polarimeters.

astro-ph.HE↗

arXiv2010

HX-POL - A Balloon-Borne Hard X-Ray Polarimeter

We report on the design and estimated performance of a balloon-borne hard X-ray polarimeter called HX-POL. The experiment uses a combination of Si and Cadmium Zinc Telluride detectors to measure the polarization of 50 keV-400 keV X-rays from cosmic sources through the dependence of the angular distribution of Compton scattered photons on the polarization direction. On a one-day balloon flight, HX-POL would allow us to measure the polarization of bright Crab-like sources for polarization degrees well below 10%. On a longer (15-30 day) flight from Australia or Antarctica, HX-POL would be be able to measure the polarization of bright galactic X-ray sources down to polarization degrees of a few percent. Hard X-ray polarization measurements provide unique venues for the study of particle acceleration processes by compact objects and relativistic outflows. In this paper, we discuss the overall instrument design and performance. Furthermore, we present results from laboratory tests of the Si and CZT detectors.

astro-ph↗

arXiv2007

EXIST's Gamma-Ray Burst Sensitivity

We use semi-analytic techniques to evaluate the burst sensitivity of designs for the EXIST hard X-ray survey mission. Applying these techniques to the mission design proposed for the Beyond Einstein program, we find that with its very large field-of-view and faint gamma-ray burst detection threshold, EXIST will detect and localize approximately two bursts per day, a large fraction of which may be at high redshift. We estimate that EXIST's maximum sensitivity will be ~4 times greater than that of Swift's Burst Alert Telescope. Bursts will be localized to better than 40 arcsec at threshold, with a burst position as good as a few arcsec for strong bursts. EXIST's combination of three different detector systems will provide spectra from 3 keV to more than 10 MeV. Thus, EXIST will enable a major leap in the understanding of bursts, their evolution, environment, and utility as cosmological probes.

astro-ph↗

arXiv2007

Wide Field Hard X-ray Survey Telescope: ProtoEXIST1

We report our progress on the development of pixellated imaging CZT detector arrays for our first-generation balloon-borne wide-field hard X-ray (20 - 600 keV) telescope, ProtoEXIST1. Our ProtoEXIST program is a pathfinder for the High Energy Telescope (HET) on the Energetic X-ray Imaging Survey telescope (EXIST), a proposed implementation of the Black Hole Finder Probe. ProtoEXIST1 consists of four independent coded-aperture telescopes with close-tiled (~0.4 mm gaps) CZT detectors that preserve their 2.5mm pixel pitch. Multiple shielding/field-of-view configurations are planned to identify optimal geometry for the HET in EXIST. The primary technical challenge in ProtoEXIST is the development of large area, close-tiled modules of imaging CZT detectors (1000 cm2 for ProtoEXIST1), with all readout and control systems for the ASIC readout vertically stacked. We describe the overall telescope configuration of ProtoEXIST1 and review the current development status of the CZT detectors, from individual detector crystal units (DCUs) to a full detector module (DM). We have built the first units of each component for the detector plane and have completed a few Rev2 DCUs (2x2 cm2), which are under a series of tests. Bare DCUs (pre-crystal bonding) show high, uniform ASIC yield (~70%) and ~30% reduction in electronics noise compared to the Rev1 equivalent. A Rev1 DCU already achieved ~1.2% FWHM at 662 keV, and preliminary analysis of the initial radiation tests on a Rev2 DCU shows ~ 4 keV FWHM at 60 keV (vs. 4.7 keV for Rev1). We therefore expect about <~1% FWHM at 662 keV with the Rev2 detectors.

astro-ph↗

arXiv2006

CZT in Space Based Hard-X-ray Astronomy

One of the key aspects of a detector material for space-borne hard X-ray and gamma-ray telescopes is the rate of prompt and delayed background events generated inside the material by charged and neutral particles striking the detector. These particles are Cosmic Rays, particles trapped in Earth's magnetic field, and secondaries from Cosmic Ray interacting with the atmosphere and the spacecraft. Here, we present a preliminary study of Cadmium Zinc Telluride (CZT) and its behaviour in space environments. We have used the simulation package MGGPOD to estimate the background of the CZT detectors in the proposed Energetic X-ray Imaging Survey Telescope (EXIST) for possible orbital parameters. The EXIST mission will make use of 6 square meters of 0.5 cm thick CZT detectors to record cosmic X-rays in the energy range from 10 keV to 600 keV. The detectors will be shielded by a fully or partly active shield. For the specific detector and shielding geometry considered here and an orbit with a low (7 deg) inclination, the background rate is dominated by the diffuse extragalactic below 200 keV. Prompt and delayed hadronic backgrounds grow increasingly important above this energy, becoming the main contributors to the total background above 1 MeV. A fully active shield performs slightly better than a half active/half passive shield.

astro-ph↗

arXiv2006

Test of Thick Pixelated Orbotech Detectors with and without Steering Grids

We report here on the optimization of 0.5 cm thick pixelated Orbotech CZT detectors with regards to the best contacting materials and the use of steering grids. We evaluated the performance of different contacting materials. Our study differs from earlier ones in that we investigated the performance of different anode and cathode materials separately. We obtain the best performance with Au cathodes. For different anode materials Ti and In give the best energy resolutions. The detector (2.0 x 2.0 x 0.5 cm, 8 x 8 pixels) shows excellent 59 keV, 122 keV and 662 keV energy resolutions of 1.4 keV, 1.9 keV, and 7.4 keV, respectively. Furthermore, we report on using steering grids to improve on the performance of the pixelated detectors. Previously, the benefit of steering grids had been limited by additional electronic noise associated with currents between the negatively biased steering grids and the anode pixels. We are currently exploring the possibility to isolate the steering grid from the CZT substrates by a thin layer of Al$_2$O$_3$. We performed a series of measurements to determine by how much the isolation layer reduces the grid-pixel currents. Comparing the currents between two Au contacts before and after isolating one of the two contacts from the CZT with a 700 nm thick layer of Al2O3, we measure that the isolation layer reduces the currents by a factor of about 10 at 500 V. We present some results from a detector before and after deposition of an isolated steering grid. The grid indeed improves on the detectors energy resolution and detection efficiency. We show that simulations can be used to model the anode to cathode charge correlation in excellent agreement with the experimental results.

astro-ph↗

arXiv2006

Using the Active Collimator and Shield Assembly of an EXIST-Type Mission as a Gamma-Ray Burst Spectrometer

The Energetic X-ray Imaging Survey Telescope (EXIST) is a mission design concept that uses coded masks seen by Cadmium Zinc Telluride (CZT) detectors to register hard X-rays in the energy region from 10 keV to 600 keV. A partially active or fully active anti-coincidence shield/collimator with a total area of between 15 and 35 square meters will be used to define the field of view of the CZT detectors and to suppress the background of cosmic-ray-induced events. In this paper, we describe the use of a sodium activated cesium iodide shield/collimator to detect gamma-ray bursts (GRBs) and to measure their energy spectra in the energy range from 100 keV up to 10 MeV. We use the code GEANT4 to simulate the interactions of photons and cosmic rays with the spacecraft and instrument and the code DETECT2000 to simulate the optical properties of the scintillation detectors. The shield collimator achieves a nu-F-nu sensitivity of 3 x 10^(-9) erg cm^(-2) s^(-1) and 2 x 10^(-8) erg cm^(-2) s^(-1) at 100 keV and 600 keV, respectively. The sensitivity is well matched to that of the coded mask telescope. The broad energy coverage of an EXIST-type mission with active shields will constrain the peak of the spectral energy distribution (SED) for a large number of GRBs. The measurement of the SED peak may be key for determining photometric GRB redshifts and for using GRBs as cosmological probes.

astro-ph↗