arXiv subjects

A. Grelli

Publications and source records attributed to A. Grelli.

6 recordsLinked to original sources

arXiv2025

Sensor operating point calibration and monitoring of the ALICE Inner Tracking System during LHC Run 3

The new Inner Tracking System (ITS2) of the ALICE experiment began operation in 2021 with the start of LHC Run 3. Compared to its predecessor, ITS2 offers substantial improvements in pointing resolution, tracking efficiency at low transverse momenta, and readout-rate capabilities. The detector employs silicon Monolithic Active Pixel Sensors (MAPS) featuring a pixel size of 26.88$\times$29.24 $\mu$m$^2$ and an intrinsic spatial resolution of approximately 5 $\mu$m. With a remarkably low material budget of 0.36% of radiation length ($X_{0}$) per layer in the three innermost layers and a total sensitive area of about 10 m$^2$, the ITS2 constitutes the largest-scale application of MAPS technology in a high-energy physics experiment and the first of its kind operated at the LHC. For stable data taking, it is crucial to calibrate different parameters of the detector, such as in-pixel charge thresholds and the masking of noisy pixels. The calibration of 24120 monolithic sensors, comprising a total of 12.6$\times$10$^{9}$ pixels, represents a major operational challenge. This paper presents the methods developed for the calibration of the ITS2 and outlines the strategies for monitoring and dynamically adjusting the detector's key performance parameters over time.

physics.ins-det↗

arXiv2025

Exploring unique design features of the Monolithic Stitched Sensor with Timing (MOST): yield, powering, timing, and sensor reverse bias

Monolithic stitched CMOS sensors are explored for the upgrade of Inner Tracking System of the ALICE experiment (ITS3) and the R&D of the CERN Experimental Physics Department. To learn about stitching, two 26 cm long stitched sensors, the Monolithic Stitched Sensor (MOSS), and the Monolithic Stitched Sensor with Timing (MOST), were implemented in the Engineering Round 1 (ER1) in the TPSCo 65nm ISC technology. Contrary to the MOSS, powered by 20 distinct power domains accessible from separate pads, the MOST has one global analog and digital power domain to or from which small fractions of the matrix can be connected or disconnected by conservatively designed power switches to prevent shorts or defects from affecting the full chip. Instead of the synchronous readout in the MOSS, the MOST immediately transfers hit information upon a hit, preserving timing information. The sensor reverse bias is also applied through the bias of the front-end rather than by a reverse substrate bias. This paper presents the first characterization results of the MOST, with the focus on its specific characteristics, including yield analysis, precise timing measurements, and the potential of its alternative biasing approach for improved sensor performance.

physics.ins-det↗

arXiv2021

First demonstration of in-beam performance of bent Monolithic Active Pixel Sensors

A novel approach for designing the next generation of vertex detectors foresees to employ wafer-scale sensors that can be bent to truly cylindrical geometries after thinning them to thicknesses of 20-40$\mu$m. To solidify this concept, the feasibility of operating bent MAPS was demonstrated using 1.5$\times$3cm ALPIDE chips. Already with their thickness of 50$\mu$m, they can be successfully bent to radii of about 2cm without any signs of mechanical or electrical damage. During a subsequent characterisation using a 5.4GeV electron beam, it was further confirmed that they preserve their full electrical functionality as well as particle detection performance. In this article, the bending procedure and the setup used for characterisation are detailed. Furthermore, the analysis of the beam test, including the measurement of the detection efficiency as a function of beam position and local inclination angle, is discussed. The results show that the sensors maintain their excellent performance after bending to radii of 2cm, with detection efficiencies above 99.9% at typical operating conditions, paving the way towards a new class of detectors with unprecedented low material budget and ideal geometrical properties.

physics.ins-det↗

arXiv2019

Future physics opportunities for high-density QCD at the LHC with heavy-ion and proton beams

The future opportunities for high-density QCD studies with ion and proton beams at the LHC are presented. Four major scientific goals are identified: the characterisation of the macroscopic long wavelength Quark-Gluon Plasma (QGP) properties with unprecedented precision, the investigation of the microscopic parton dynamics underlying QGP properties, the development of a unified picture of particle production and QCD dynamics from small (pp) to large (nucleus--nucleus) systems, the exploration of parton densities in nuclei in a broad ($x$, $Q^2$) kinematic range and the search for the possible onset of parton saturation. In order to address these scientific goals, high-luminosity Pb-Pb and p-Pb programmes are considered as priorities for Runs 3 and 4, complemented by high-multiplicity studies in pp collisions and a short run with oxygen ions. High-luminosity runs with intermediate-mass nuclei, for example Ar or Kr, are considered as an appealing case for extending the heavy-ion programme at the LHC beyond Run 4. The potential of the High-Energy LHC to probe QCD matter with newly-available observables, at twice larger center-of-mass energies than the LHC, is investigated.

hep-ph↗

arXiv2017

Heavy-flavor production and medium properties in high-energy nuclear collisions - What next?

Open and hidden heavy-flavor physics in high-energy nuclear collisions are entering a new and exciting stage towards reaching a clearer understanding of the new experimental results with the possibility to link them directly to the advancement in lattice Quantum Chromo-dynamics (QCD). Recent results from experiments and theoretical developments regarding open and hidden heavy-flavor dynamics have been debated at the Lorentz Workshop "Tomography of the quark-gluon plasma with heavy quarks}, which was held in October 2016 in Leiden, the Netherlands. In this contribution, we summarize identified common understandings and developed strategies for the upcoming five years, which aim at achieving a profound knowledge of the dynamical properties of the quark-gluon plasma.

nucl-th↗

arXiv2006

Gas Analysis and Monitoring Systems for the RPC Detector of CMS at LHC

The Resistive Plate Chambers (RPC) detector of the CMS experiment at the LHC proton collider (CERN, Switzerland) will employ an online gas analysis and monitoring system of the freon-based gas mixture used. We give an overview of the CMS RPC gas system, describe the project parameters and first results on gas-chromatograph analysis. Finally, we report on preliminary results for a set of monitor RPC.

physics.ins-det↗