arXiv subjects

A. Tishelman-Charny

Publications and source records attributed to A. Tishelman-Charny.

4 recordsLinked to original sources

arXiv2026

Mortality of ultra-thin LGADs and PiN diodes from high energy deposition

Low Gain Avalanche Diodes are prime candidates for high-resolution timing applications in High Energy Physics, Nuclear science, and several other fields. Operating these devices in high-radiation environments presents various hazards, including the risk of their permanent degradation or destruction caused by effects such as Single Event Burnout. Studies using minimum ionizing particles found a greatly reduced Single Event Burnout risk by operating below a bias voltage corresponding to an average electric field of 12 V/$μ$m - however, as high energy particle colliders produce a wide energy spectrum of radiation, it is crucial to understand this phenomenon and other possible damage mechanisms at energy deposition levels greater than those of minimum ionizing particles. This was achieved by pre-irradiating LGADs and PiN diodes with active thicknesses of 20, 30, and 50 $μ$m up to 1.5 $\times$ 10$^{15}$ $\mathrm{n_{eq}/cm^2}$, and exposing them to beams of protons and heavy ions (C, O, Fe, Au) at the BNL Tandem van de Graaff accelerator. Several mortality categories were observed, defined by different electrical and mechanical damage signatures. This furthers our understanding of permanent radiation damage of silicon devices, crucial towards mitigating Single Event Burnout and other damage mechanisms to safely operate future detectors.

physics.ins-det↗

arXiv2025

First stave results towards mitigating sensor fracturing with interposers in the ATLAS ITk strips barrel

At the conclusion of Run 3 of the Large Hadron Collider (LHC) at CERN, the accelerator complex will be upgraded to the High-Luminosity LHC (HL-LHC), allowing it to increase the dataset sizes of LHC experiments by about a factor of 20. This significant increase in dataset size will improve the sensitivity and precision of all physics analyses from LHC experiments, but will come with a more challenging data-taking environment. In order to handle this, the ATLAS detector will undergo a substantial upgrade, including an upgrade of its inner tracker to an all-silicon tracker called the Inner Tracker (ITk), made of pixel and strip sub-detectors. During the pre-production phase of the ITk strips, it was discovered that thermally cycling modules loaded onto local support structures led to physical fractures in silicon sensors due to the induced thermal stress. This is understood to be the result of several factors, including the difference in coefficients of thermal expansion between the different module layers, and the close proximity of the module electrical components. Several mitigation strategies were tested to reduce the rate of module fracturing. This paper describes the assembly setup, testing setups, and electrical testing results of ITk strips barrel modules loaded onto local support structures. 69 of 70 modules with an in-built additional kapton layer were found to survive testing down to -70°C.

physics.ins-det↗

arXiv2024

An extreme thermal cycling reliability test of ATLAS ITk Strips barrel modules

At the end of Run 3 of the Large Hadron Collider (LHC), the accelerator complex will be upgraded to the High-Luminosity LHC (HL-LHC) in order to increase the total amount of data provided to its experiments. To cope with the increased rates of data, radiation, and pileup, the ATLAS detector will undergo a substantial upgrade, including a replacement of the Inner Detector with a future Inner Tracker, called the ITk. The ITk will be composed of pixel and strip sub-detectors, where the strips portion will be composed of 17,888 silicon strip detector modules. During the HL-LHC running period, the ITk will be cooled and warmed a number of times from about ${-35}^\circ$C to room temperature as part of the operational cycle, including warm-ups during yearly shutdowns. To ensure ITk Strips modules are functional after these expected temperature changes, and to ensure modules are mechanically robust, each module must undergo ten thermal cycles and pass a set of electrical and mechanical criteria before it is placed on a local support structure. This paper describes the thermal cycling Quality Control (QC) procedure, and results from the barrel pre-production phase (about 5% of the production volume). Additionally, in order to assess the headroom of the nominal QC procedure of 10 cycles and to ensure modules don't begin failing soon after, four representative ITk Strips barrel modules were thermally cycled 100 times - this study is also described.

physics.ins-det↗

arXiv2017

A Magnetic Field Cloak For Charged Particle Beams

Shielding charged particle beams from transverse magnetic fields is a common challenge for particle accelerators and experiments. We demonstrate that a magnetic field cloak is a viable solution. It allows for the use of dipole magnets in the forward regions of experiments at an Electron Ion Collider (EIC) and other facilities without interfering with the incoming beams. The dipoles can improve the momentum measurements of charged final state particles at angles close to the beam line and therefore increase the physics reach of these experiments. In contrast to other magnetic shielding options (such as active coils), a cloak requires no external powering. We discuss the design parameters, fabrication, and limitations of a magnetic field cloak and demonstrate that cylinders made from 45 layers of YBCO high-temperature superconductor, combined with a ferromagnetic shell made from epoxy and stainless steel powder, shield more than 99% of a transverse magnetic field of up to 0.45 T (95 % shielding at 0.5 T) at liquid nitrogen temperature. The ferromagnetic shell reduces field distortions caused by the superconductor alone by 90% at 0.45 T.

physics.acc-ph↗