arXiv subjects

A. V. Zlobin

Publications and source records attributed to A. V. Zlobin.

At least 19 recordsLinked to original sources

arXiv2025

A Computational Procedure for Assessing I$_c$($\varepsilon$) in Nb$_3$Sn/Bi-2212 Hybrid Magnets

The critical current of superconductors is commonly measured by testing unloaded wires under an external magnetic field. While stressed by intense Lorentz forces, the existing HTS/LTS superconductors are prone to a reduction in critical current before reaching their structural mechanical limit. In this work, the magnetic and mechanical analysis of the FNAL 4-layer Bi-2212/Nb$_3$Sn hybrid dipole magnet is reported, aimed at predicting the critical current degradation for both the superconductors during powering at 16 T. All the Rutherford cables in the coils of the hybrid magnet were modeled at the strand level in Ansys APDL with the heterogeneous cable model. Utilizing this detailed geometry, it was possible to evaluate the effects of strain on the critical current degradation for both the Nb$_3$Sn and Bi-2212 superconductors under the intense Lorentz forces. The analysis presented in this paper integrates strain-dependent critical current laws, with parameters derived from experimental data, to simulate the hybrid magnet's performance for all possible current-powering configurations. The proposed methodology enables a detailed assessment of conductor integrity and I$_C$($\varepsilon$) reduction in existing hybrid magnet designs, providing a versatile and rigorous framework for optimizing future high-field hybrid magnets.

physics.ins-det↗

arXiv2025

Magnetic and Mechanical Analysis of Bi-2212 Rutherford Cable in a Cos-Theta Sub-Scale Dipole Coil

The U.S. Magnet Development Program (US-MDP) explores high-field accelerator magnets compatible with operational conditions beyond the limits of Nb$_3$Sn technology. The ongoing R\&D High-Temperature Superconductors (HTS) suggests using Bi$_2$Sr$_2$CaCu$_2$O$_{8-x}$ (Bi-2212) as superconducting element. Bi-2212 Rutherford cables maintain a high critical current (I$_C$) when exposed to a large external magnetic field. However, Bi-2212 exhibits an oversensitive stress-strain response when subject to large Lorentz forces. This paper reports on the magnetic and mechanical analysis of the Bi-2212 cosine-theta insert being developed at Fermilab for a hybrid magnet composed of two external layers of Nb$_3$Sn and two internal layers of Bi-2212. We performed a FEM analysis of the insert to estimate the HTS stress state in the coil's strands under magnetic and mechanical loads.

physics.acc-ph↗

arXiv2024

Conceptual Design of A 20 T Dipole Based on Hybrid REBCO/Nb3Sn Cos-theta Coil*

This paper presents a design concept of an HTS/LTS hybrid dipole with 50 mm aperture and 20 T nominal field based on a cos-theta coil and a cold iron yoke. The HTS part of magnet coil uses REBCO Twisted Stacked Tape cable. The LTS part is graded and made of two Nb3Sn Rutherford cables. Due to high sensitivity of HTS/LTS coils to large stresses and strains at high fields, a Stress Management (SM) concept combined with the cos-theta coil geometry is used. The results of magnet magnetic analysis are presented and discussed.

physics.acc-ph↗

arXiv2024

Development and Test of a Large-aperture Nb3Sn Cos-theta Dipole Coil with Stress Management

The design concept of the Electron Ion Collider (EIC), which is under construction at BNL, considers adding a 2nd Interaction Region (IR) and detector to the machine after completion of the present EIC project. Recent progress with development and fabrication of large-aperture high-field magnets based on the Nb3Sn technology for the HL-LHC makes this technology interesting for the 2nd EIC IR. This paper summarizes the results of feasibility studies of large-aperture high-field Nb3Sn dipoles and quadrupoles for the 2nd EIC IR.

physics.acc-ph↗

arXiv2023

Large-Aperture High-Field NB3SN Magnets for the 2nd EIC Interaction Region*

physics.acc-ph↗

arXiv2023

20 T Dipole Magnet Based on Hybrid HTS/LTS Cos-Theta Coils with Stress Management

This paper presents the design concept of the dipole magnet with 50 mm aperture, 20 T nominal field and 13% margin based on a six-layer cos-theta (CT) hybrid coil design. Due to the high stresses and strains in the coil at high field, Stress Management (SM) elements are implemented in the CT coil geometry. The results of magnet magnetic analysis are presented and discussed. The key parameters of this design are compared with the parameters of similar magnets based on block-type and canted cos-theta coils.

physics.acc-ph↗

arXiv2023

Design and Assembly of a Large-aperture Nb3Sn Cos-theta Dipole Coil with Stress Management in Dipole Mirror Configuration

The stress-management cos-theta (SMCT) coil is a new concept which has been proposed and is being developed at Fermilab in the framework of US Magnet Development Program (US-MDP) for high-field and/or large-aperture accelerator magnets based on low-temperature and high-temperature superconductors. The SMCT structure is used to reduce large coil deformations under the Lorentz forces and, thus, the excessively large strains and stresses in the coil. A large-aperture Nb3Sn SMCT dipole coil has been developed and fabricated at Fermilab to demonstrate and test the SMCT concept including coil design, fabrication technology and performance. The first SMCT coil has been assembled with 60-mm aperture Nb3Sn coil inside a dipole mirror configuration and will be tested separately and in series with the insert coil. This paper summarizes the large-aperture SMCT coil design and parameters and reports the coil fabrication steps and its assembly in dipole mirror configuration.

physics.app-ph↗

arXiv2023

Conceptual design of 20 T hybrid accelerator dipole magnets

Hybrid magnets are currently under consideration as an economically viable option towards 20 T dipole magnets for next generation of particle accelerators. In these magnets, High Temperature Superconducting (HTS) materials are used in the high field part of the coil with so-called insert coils, and Low Temperature Superconductors (LTS) like Nb3Sn and Nb-Ti superconductors are used in the lower field region with so-called outsert coils. The attractiveness of the hybrid option lays on the fact that, on the one hand, the 20 T field level is beyond the Nb3Sn practical limits of 15-16 T for accelerator magnets and can be achieved only via HTS materials; on the other hand, the high cost of HTS superconductors compared to LTS superconductors makes it advantageous exploring a hybrid approach, where the HTS portion of the coil is minimized. We present in this paper an overview of different design options aimed at generating 20 T field in a 50 mm clear aperture. The coil layouts investigated include the Cos-theta design (CT), with its variations to reduce the conductor peak stress, namely the Canted Cos-theta design (CCT) and the Stress Management Cos-theta design (SMCT), and, in addition, the Block-type design (BL) including a form of stress management and the Common-Coil design (CC). Results from a magnetic and mechanical analysis are discussed, with particular focus on the comparison between the different options regarding quantity of superconducting material, field quality, conductor peak stress, and quench protection.

physics.acc-ph↗

arXiv2022

Accelerator Technology Magnets

The Snowmass community exercise started in April 2020 to identify and document a scientific vision for the future of particle physics in the US and international partners. The AF7-Magnets working group was charged to a) address the potential contributions of magnet technology to future HEP facilities, b) evaluate the R\&D required to enable these opportunities, c) estimate the time and cost scales of these efforts, and d) assess the needs for associated fabrication infrastructure and test facilities. This report addresses the working group charge, summarizes the status of accelerator and detector magnet technologies, and discuss ideas and plans to push this key area of the US and international HEP to new horizons.

physics.acc-ph↗

arXiv2022

Snowmass'21 Accelerator Frontier Report

In 2020-2022, extensive discussions and deliberations have taken place in corresponding topical working groups of the Snowmass Accelerator Frontier (AF) and in numerous joint meetings with other Frontiers, Snowmass-wide meetings, a series of Colloquium-style Agoras, cross-Frontier Forums on muon and electron-positron colliders and the collider Implementation Task Force (ITF). The outcomes of these activities are summarized in this Accelerator Frontier report.

physics.acc-ph↗

arXiv2022

Minimum Quench Energy Of Nb$_3$Sn Wires With High Specific Heat Tape

A major problem of state-of-the-art Nb$_3$Sn accelerator magnets is their long training due to thermo-mechanical perturbations. Increasing the specific heat, $C_p$, of the Rutherford cable would reduce and/or eliminate training by limiting the coils temperature rise. This paper studies feasibility of increasing the $C_p$ of Rutherford-type cables by using thin composite Cu/$Gd_2$O$_3$ and Cu/$Gd_2$O$_2$S tapes produced by Hyper Tech Research, Inc. The tape can be either wrapped around the cable, placed on the cable wide faces under the insulation, and/or inserted as a core. Wire samples outfitted with these high-$C_p$ ribbons, or tapes, were prepared and tested at FNAL for their Minimum Quench Energy (MQE). At 90%I$_c$ and 15 T, the average gain of MQE of the Nb$_3$Sn wire soldered to the Cu/$Gd_2$O$_2$S 55 micrometer thick ribbon was 2.5, and further increased at larger transport currents.

physics.app-ph↗

arXiv2022

Development of a 120-mm Aperture Nb3Sn Dipole Coil with Stress Management

This paper describes a 120-mm aperture 2-layer dipole coil with stress management (SM) developed at Fermilab based on cos-theta coil geometry. A model of the coil support structure made of plastic was printed using additive manufacturing technology and used for practice coil winding. The real coil support structure was printed using the 316 stainless steel. The results of the SM structure size control and the key coil fabrication steps are reported in the paper. The design of coil SM structure and the coil FEA in the dipole mirror test configurations are presented and discussed.

physics.app-ph↗

arXiv2022

White Paper on High Temperature Superconducting Bi-2212 Magnets for Energy Frontier Circular Colliders

As the only high-temperature superconducting (HTS) material available as an isotropic, twisted, multifilamentary round wire, Bi-2212 is very promising for expanding the high-field superconducting accelerator magnet toolbox beyond the round-wire, isotropic Nb-Ti and Nb3Sn conductors used by HEP so far. In this paper, we describe the important roles that Bi-2212 might play for future high energy circular colliders including both high energy proton and muon colliders. We describe its present technology status (conductor development, magnet design concepts, prototype magnet status) and then provide a ten-year plan for >15 T accelerator magnets and >25 T solenoid magnets within an integrated strategy to engage industry and the entire US and international scientific enterprise interested in HTS magnet applications.

physics.acc-ph↗

arXiv2022

Critical problems of energy frontier Muon Colliders: optics, magnets and radiation

This White Paper brings together our previous studies on a Muon Collider (MC) and presents a design concept of the 6 TeV MC optics, the superconducting (SC) magnets, and a preliminary analysis of the protection system to reduce magnet radiation loads as well as particle backgrounds in the detector. The SC magnets and detector protection considerations impose strict limitations on the lattice choice, hence the design of the collider optics, magnets and Machine Detector Interface (MDI) are closely intertwined. As a first approximation we use the Interaction Region (IR) design with beta-star=3 mm, whereas for the arcs we re-scale the arc cell design of the 3 TeV MC. Traditional cos-theta coil geometry and Nb3Sn superconductor were used to provide field maps for the analysis and optimization of the arc lattice and IR design, as well as for studies of beam dynamics and magnet protection against radiation. The stress management in the coil will be needed to avoid large degradation or even damage of the brittle SC coils. In the assumed IR designs, the dipoles close to the Interaction Point (IP) and tungsten masks in each IR (to protect magnets) help reducing background particle fluxes in the detector by a substantial factor. The tungsten nozzles in the 6 to 600 cm region from the IP, assisted by the detector solenoid field, trap most of the decay electrons created close to the IP as well as most of the incoherent electron-positron pairs generated in the IP. With sophisticated tungsten, iron, concrete and borated polyethylene shielding in the MDI region, the total reduction of background loads by more than three orders of magnitude can be achieved.

physics.acc-ph↗

arXiv2022

Solving Critical Problems of the Muon Collider Higgs Factory: Optics, Magnets and their Protection, Detector Backgrounds

A low-energy medium-luminosity Muon Collider (MC) is being studied as a possible Higgs Factory (HF). Electrons from muon decays will deposit more than 300 kW in superconducting magnets of the HF collider ring. This imposes significant challenges to superconducting (SC) magnets used in the MC storage ring (SR) and interaction regions (IR). Magnet designs are proposed which provide high operating gradient and magnetic field in a large aperture to accommodate the large size of muon beams (due to low beta*), as well as a cooling system to intercept the large heat deposition from the showers induced by decay electrons. The distribution of heat deposition in the MC SR lattice elements requires large-aperture magnets in order to accommodate thick high-Z absorbers to protect the SC coils. Based on the developed MARS15 model and intensive simulations, a sophisticated radiation protection system was designed for the collider SR and IR to bring the peak power density in the superconducting coils below the quench limit and reduce the dynamic heat deposition in the cold mass by a factor of 100. The system consists of tight tungsten masks in the magnet interconnect regions and elliptical tungsten liners in the magnet aperture optimized individually for each magnet. These also reduce the background particle fluxes in the collider detector.

physics.acc-ph↗

arXiv2020

Heat Diffusion in high-$C_p$ Nb$_3$Sn Composite Superconducting Wires

A major focus of Nb$_3$Sn accelerator magnets is on significantly reducing or eliminating their training. Demonstration of an approach to increase the $C_p$ of Nb$_3$Sn magnets using new materials and technologies is very important both for particle accelerators and light sources. It would improve thermal stability and lead to much shorter magnet training, with substantial savings in machines' commissioning costs. Both Hypertech and Bruker-OST have attempted to introduce high-$C_p$ elements in their wire design. This paper includes a description of these advanced wires, the finite element model of their heat diffusion properties as compared with the standard wires, and whenever available, a comparison between the minimum quench energy (MQE) calculated by the model and actual MQE measurements on wires.

physics.acc-ph↗

arXiv2018

The Higgs Factory Muon Collider Superconducting Magnets and Their Protection Against Beam Decay Radiation

Low-energy medium-luminosity Muon Collider (MC) is being studied as a possible Higgs Factory (HF). Electrons from muon decays will deposit more than 300 kW in superconducting magnets of the HF collider ring. This imposes significant challenges to superconducting (SC) magnets used in the MC storage ring (SR) and interaction regions (IR). The magnet designs are proposed which provide high operating gradient and magnetic field in a large aperture to accommodate the large size of muon beams due to low \b{eta}* as well as the cooling system to intercept the large heat deposition from the showers induced by decay electrons. Specific distribution of heat deposition in the lattice elements MC SR requires large aperture magnets to accommodate thick high-Z absorbers to protect the SC coils. Based on the developed MARS15 model and intense simulations, a sophisticated radiation protection system was designed for the collider SR and IR to bring the peak power density in the superconducting coils below the quench limit and reduce the dynamic heat deposition in the cold mass by a factor of 100. The system consists of tight tungsten masks in the magnet interconnect regions and elliptical tungsten liners in magnet aperture optimized for each magnet. It also reduces the background particle fluxes in the collider detector.

physics.acc-ph↗

arXiv2014

Storage Ring And Interaction Region Magnets For A μ+μ- Higgs Factory

A low-energy Muon Collider (MC) offers unique opportunities to study the recently found Higgs boson. However, due to a relatively large beam emittance with moderate cooling in this machine, large-aperture high- field superconducting (SC) magnets are required. The magnets need also an adequate margin to operate at a large radiation load from the muon decay showers. General specifications of the SC dipoles and quadrupoles for the 125 GeV c.o.m. Higgs Factory with an average luminosity of ~2x10**31 cm-2s-1 are formulated. Magnet conceptual designs and parameters are reported. The impact of the magnet fringe fields on the beam dynamics as well as the IR and lattice magnet protection from radiation are also reported and discussed.

physics.acc-ph↗