arXiv subjects

A. Wilkinson

Publications and source records attributed to A. Wilkinson.

At least 19 recordsLinked to original sources

arXiv2025

Readout electronics for low occupancy High-Pressure Gas TPCs

HPgTPCs have benefits such as low energy threshold, magnetisability, and 4$\pi$ acceptance, making them ideal for neutrino experiments such as DUNE. We present the design of an FPGA-based solution optimised for ND-GAr, which is part of the Phase-II more capable near detector for DUNE. These electronics reduce the cost significantly compared to using collider readout electronics which are typically designed for much higher occupancy and therefore, for example, need much larger numbers of FPGAs and power per channel. We demonstrate the performance of our electronics with the TOAD at Fermilab in the US at a range of pressures and gas mixtures up to 4.5barA, reading out ~10000 channels from a multi-wire proportional chamber. The operation took place between April and July of 2024. We measure the noise characteristics of the system to be sufficiently low and we identify sources of noise that can be further mitigated in the next iteration. We also note that the cooling scheme used in the test requires improvement before full-scale deployment. Despite these necessary improvements, we show that the system can fulfil the needs of a HPgTPC for a fraction of the price of collider readout electronics.

physics.ins-det↗

arXiv2021

Cosmic evolution of the H2 mass density and the epoch of molecular gas

We present new empirical constraints on the evolution of $\rho_{\rm H_2}$, the cosmological mass density of molecular hydrogen, back to $z\approx2.5$. We employ a statistical approach measuring the average observed $850\mu{\rm m}$ flux density of near-infrared selected galaxies as a function of redshift. The redshift range considered corresponds to a span where the $850\mu{\rm m}$ band probes the Rayleigh-Jeans tail of thermal dust emission in the rest-frame, and can therefore be used as an estimate of the mass of the interstellar medium (ISM). Our sample comprises of ${\approx}150,000$ galaxies in the UKIDSS-UDS field with near-infrared magnitudes $K_{\rm AB}\leq25$ mag and photometric redshifts with corresponding probability distribution functions derived from deep 12-band photometry. With a sample approximately 2 orders of magnitude larger than in previous works we significantly reduce statistical uncertainties on $\rho_{\rm H_2}$ to $z\approx2.5$. Our measurements are in broad agreement with recent direct estimates from blank field molecular gas surveys, finding that the epoch of molecular gas coincides with the peak epoch of star formation with $\rho_{\rm H_2}\approx2\times10^7\,{\rm M_\odot}\,{\rm Mpc^{-3}}$ at $z\approx2$. We demonstrate that $\rho_{\rm H_2}$ can be broadly modelled by inverting the star-formation rate density with a fixed or weakly evolving star-formation efficiency. This 'constant efficiency' model shows a similar evolution to our statistically derived $\rho_{\rm H_2}$, indicating that the dominant factor driving the peak star formation history at $z\approx2$ is a larger supply of molecular gas in galaxies rather than a significant evolution of the star-formation rate efficiency within individual galaxies.

astro-ph.GA↗

arXiv2017

$C^1$ density of stable ergodicity

We prove a $C^1$ version of a conjecture by Pugh and Shub: among partially hyperbolic volume-preserving $C^r$ diffeomorphisms, $r>1$, the stably ergodic ones are $C^1$-dense. To establish these results, we develop new perturbation tools for the $C^1$ topology: linearization of horseshoes while preserving entropy, and creation of "superblenders" from hyperbolic sets with large entropy.

math.DS↗

arXiv2011

Planck early results. III. First assessment of the Low Frequency Instrument in-flight performance

The scientific performance of the Planck Low Frequency Instrument (LFI) after one year of in-orbit operation is presented. We describe the main optical parameters and discuss photometric calibration, white noise sensitivity, and noise properties. A preliminary evaluation of the impact of the main systematic effects is presented. For each of the performance parameters, we outline the methods used to obtain them from the flight data and provide a comparison with pre-launch ground assessments, which are essentially confirmed in flight.

astro-ph.CO↗

arXiv2010

Planck pre-launch status: calibration of the Low Frequency Instrument flight model radiometers

The Low Frequency Instrument (LFI) on-board the ESA Planck satellite carries eleven radiometer subsystems, called Radiometer Chain Assemblies (RCAs), each composed of a pair of pseudo-correlation receivers. We describe the on-ground calibration campaign performed to qualify the flight model RCAs and to measure their pre-launch performances. Each RCA was calibrated in a dedicated flight-like cryogenic environment with the radiometer front-end cooled to 20K and the back-end at 300K, and with an external input load cooled to 4K. A matched load simulating a blackbody at different temperatures was placed in front of the sky horn to derive basic radiometer properties such as noise temperature, gain, and noise performance, e.g. 1/f noise. The spectral response of each detector was measured as was their susceptibility to thermal variation. All eleven LFI RCAs were calibrated. Instrumental parameters measured in these tests, such as noise temperature, bandwidth, radiometer isolation, and linearity, provide essential inputs to the Planck-LFI data analysis.

astro-ph.IM↗

arXiv2010

Modelling the Galactic Magnetic Field on the Plane in 2D

We present a method for parametric modelling of the physical components of the Galaxy's magnetised interstellar medium, simulating the observables, and mapping out the likelihood space using a Markov Chain Monte-Carlo analysis. We then demonstrate it using total and polarised synchrotron emission data as well as rotation measures of extragalactic sources. With these three datasets, we define and study three components of the magnetic field: the large-scale coherent field, the small-scale isotropic random field, and the ordered field. In this first paper, we use only data along the Galactic plane and test a simple 2D logarithmic spiral model for the magnetic field that includes a compression and a shearing of the random component giving rise to an ordered component. We demonstrate with simulations that the method can indeed constrain multiple parameters yielding measures of, for example, the ratios of the magnetic field components. Though subject to uncertainties in thermal and cosmic ray electron densities and depending on our particular model parametrisation, our preliminary analysis shows that the coherent component is a small fraction of the total magnetic field and that an ordered component comparable in strength to the isotropic random component is required to explain the polarisation fraction of synchrotron emission. We outline further work to extend this type of analysis to study the magnetic spiral arm structure, the details of the turbulence as well as the 3D structure of the magnetic field.

astro-ph.GA↗

arXiv2010

LFI 30 and 44 GHz receivers Back-End Modules

The 30 and 44 GHz Back End Modules (BEM) for the Planck Low Frequency Instrument are broadband receivers (20% relative bandwidth) working at room temperature. The signals coming from the Front End Module are amplified, band pass filtered and finally converted to DC by a detector diode. Each receiver has two identical branches following the differential scheme of the Planck radiometers. The BEM design is based on MMIC Low Noise Amplifiers using GaAs P-HEMT devices, microstrip filters and Schottky diode detectors. Their manufacturing development has included elegant breadboard prototypes and finally qualification and flight model units. Electrical, mechanical and environmental tests were carried out for the characterization and verification of the manufactured BEMs. A description of the 30 and 44 GHz Back End Modules of Planck-LFI radiometers is given, with details of the tests done to determine their electrical and environmental performances. The electrical performances of the 30 and 44 GHz Back End Modules: frequency response, effective bandwidth, equivalent noise temperature, 1/f noise and linearity are presented.

astro-ph.IM↗

arXiv2010

Design, development and verification of the 30 and 44 GHz front-end modules for the Planck Low Frequency Instrument

We give a description of the design, construction and testing of the 30 and 44 GHz Front End Modules (FEMs) for the Low Frequency Instrument (LFI) of the Planck mission to be launched in 2009. The scientific requirements of the mission determine the performance parameters to be met by the FEMs, including their linear polarization characteristics. The FEM design is that of a differential pseudo-correlation radiometer in which the signal from the sky is compared with a 4-K blackbody load. The Low Noise Amplifier (LNA) at the heart of the FEM is based on indium phosphide High Electron Mobility Transistors (HEMTs). The radiometer incorporates a novel phase-switch design which gives excellent amplitude and phase match across the band. The noise temperature requirements are met within the measurement errors at the two frequencies. For the most sensitive LNAs, the noise temperature at the band centre is 3 and 5 times the quantum limit at 30 and 44 GHz respectively. For some of the FEMs, the noise temperature is still falling as the ambient temperature is reduced to 20 K. Stability tests of the FEMs, including a measurement of the 1/f knee frequency, also meet mission requirements. The 30 and 44 GHz FEMs have met or bettered the mission requirements in all critical aspects. The most sensitive LNAs have reached new limits of noise temperature for HEMTs at their band centres. The FEMs have well-defined linear polarization characteristcs.

astro-ph.IM↗

arXiv2010

Noise Properties of the Planck-LFI Receivers

The Planck Low Frequency Instrument (LFI) radiometers have been tested extensively during several dedicated campaigns. The present paper reports the principal noise properties of the LFI radiometers.

astro-ph.IM↗

arXiv2010

The linearity response of the Planck-LFI flight model receivers

In this paper we discuss the linearity response of the Planck-LFI receivers, with particular reference to signal compression measured on the 30 and 44 GHz channels. In the article we discuss the various sources of compression and present a model that accurately describes data measured during tests performed with individual radiomeric chains. After discussing test results we present the best parameter set representing the receiver response and discuss the impact of non linearity on in-flight calibration, which is shown to be negligible.

astro-ph.IM↗

arXiv2010

Advanced modelling of the Planck-LFI radiometers

The Low Frequency Instrument (LFI) is a radiometer array covering the 30-70 GHz spectral range on-board the ESA Planck satellite, launched on May 14th, 2009 to observe the cosmic microwave background (CMB) with unprecedented precision. In this paper we describe the development and validation of a software model of the LFI pseudo-correlation receivers which enables to reproduce and predict all the main system parameters of interest as measured at each of the 44 LFI detectors. These include system total gain, noise temperature, band-pass response, non-linear response. The LFI Advanced RF Model (LARFM) has been constructed by using commercial software tools and data of each radiometer component as measured at single unit level. The LARFM has been successfully used to reproduce the LFI behavior observed during the LFI ground-test campaign. The model is an essential element in the database of LFI data processing center and will be available for any detailed study of radiometer behaviour during the survey.

astro-ph.IM↗

arXiv2010

Planck pre-launch status: Low Frequency Instrument calibration and expected scientific performance

We give the calibration and scientific performance parameters of the Planck Low Frequency Instrument (LFI) measured during the ground cryogenic test campaign. These parameters characterise the instrument response and constitute our best pre-launch knowledge of the LFI scientific performance. The LFI shows excellent $1/f$ stability and rejection of instrumental systematic effects; measured noise performance shows that LFI is the most sensitive instrument of its kind. The set of measured calibration parameters will be updated during flight operations through the end of the mission.

astro-ph.IM↗

arXiv2006

Dynamics of Barred Galaxies

Some 30% of disc galaxies have a pronounced central bar feature in the disc plane and many more have weaker features of a similar kind. Kinematic data indicate that the bar constitutes a major non-axisymmetric component of the mass distribution and that the bar pattern tumbles rapidly about the axis normal to the disc plane. The observed motions are consistent with material within the bar streaming along highly elongated orbits aligned with the rotating major axis. A barred galaxy may also contain a spheroidal bulge at its centre, spirals in the outer disc and, less commonly, other features such as a ring or lens. Mild asymmetries in both the light and kinematics are quite common. We review the main problems presented by these complicated dynamical systems and summarize the effort so far made towards their solution, emphasizing results which appear secure. (Truncated)

astro-ph↗

arXiv2005

CMB observations from the CBI and VSA: A comparison of coincident maps and parameter estimation methods

We present coincident observations of the Cosmic Microwave Background (CMB) from the Very Small Array (VSA) and Cosmic Background Imager (CBI) telescopes. The consistency of the full datasets is tested in the map plane and the Fourier plane, prior to the usual compression of CMB data into flat bandpowers. Of the three mosaics observed by each group, two are found to be in excellent agreement. In the third mosaic, there is a 2 sigma discrepancy between the correlation of the data and the level expected from Monte Carlo simulations. This is shown to be consistent with increased phase calibration errors on VSA data during summer observations. We also consider the parameter estimation method of each group. The key difference is the use of the variance window function in place of the bandpower window function, an approximation used by the VSA group. A re-evaluation of the VSA parameter estimates, using bandpower windows, shows that the two methods yield consistent results.

astro-ph↗

arXiv2003

Advanced pseudo-correlation radiometers for the Planck-LFI instrument

The LFI (Low Frequency Instrument) on board the ESA Planck satellite is constituted by an array of radiometric detectors actively cooled at 20 K in the 30-70 GHz frequency range in the focal plane of the Planck telescope. In this paper we present an overview of the LFI instrument, with a particular focus on the radiometer design. The adopted pseudo-correlation scheme uses a software balancing technique (with a tunable parameter called gain modulation factor) which is effective in reducing the radiometer susceptibility to amplifier instabilities also in presence of small non-idealities in the radiometric chain components, provided that the gain modulation factor is estimated with an accuracy of the order of 0.2%. These results have been recently confirmed by experimental laboratory measurements conducted on the LFI prototype radiometers at 30, 70 and 100 GHz.

astro-ph↗

arXiv2003

Synchrotron Polarization at High Galactic Latitude

We present preliminary results from mapping the high-latitude Galactic polarization with the Effelsberg Telescope at $λ$21 cm. Structures on the resulting maps are mostly on the scale of several degrees. The results show detection of polarization over most of the field, at the level of tens of percent of the synchrotron emission. The evidence of more structure in Stokes Q and U rather than in $\sqrt{Q^2+U^2}$ suggests the existence of Faraday rotation.

astro-ph↗

arXiv1999

Gravitational lensing statistics with extragalactic surveys. IV. Joint constraints from gravitational lensing statistics and CMB anisotropies

We present constraints on the cosmological constant lambda_0 and the density parameter Omega_0 from joint constraints from the analyses of gravitational lensing statistics of the Jodrell Bank-VLA Astrometric Survey (JVAS), optical gravitational lens surveys from the literature and CMB anisotropies. This is the first time that quantitative joint constraints involving lensing statistics and CMB anisotropies have been presented. Within the assumptions made, we achieve very tight constraints on both lambda_0 and Omega_0. These assumptions are cold dark matter models, no tensor components, no reionisation, CMB temperature T_CMB=2.728, number of neutrinos n_nu=3, helium abundance Y_He=0.246, spectral index n_s=1.0, Hubble constant H_0=68km/s/Mpc, baryonic density Omega_b=0.05. All models were normalised to the COBE data and no closed models (k=+1) were computed. Using the CMB data alone, the best-fit model has lambda_0=0.60 and Omega_0=0.34 and at 99% confidence the lower limit on lambda_0+Omega_0 is 0.8. Including constraints from gravitational lensing statistics doesn't change this significantly, although it does change the allowed region of parameter space. A universe with lambda_0=0 is ruled out for any value of Omega_0 at better than 99% confidence using the CMB alone. Combined with constraints from lensing statistics, lambda_0=0 is also ruled out at better than 99% confidence. As the region of parameter space allowed by the CMB is, within our assumptions, much smaller than that allowed by lensing statistics, the main result of combining the two is to change the range of parameter space allowed by the CMB along its axis of degeneracy.

astro-ph↗

arXiv1999

CMB observations with the Jodrell Bank - IAC interferometer at 33 GHz

The paper presents the first results obtained with the Jodrell Bank - IAC two-element 33 GHz interferometer. The instrument was designed to measure the level of the Cosmic Microwave Background (CMB) fluctuations at angular scales of 1 - 2 degrees. The observations analyzed here were taken in a strip of the sky at Dec = +41 deg with an element separation of 16.7 lambda, which gives a maximum sensitivity to ~1.6 deg structures on the sky. The data processing and calibration of the instrument are described. The sensitivity achieved in each of the two channels is 7 micro K per resolution element. A reconstruction of the sky at Dec = +41 deg using a maximum entropy method shows the presence of structure at a high level of significance. A likelihood analysis, assuming a flat CMB spatial power spectrum, gives a best estimate of the level of CMB fluctuations of Delta Tl = 43 (+13,-12) micro K for the range l = 109 +/- 19; the main uncertainty in this result arises from sample variance. We consider that the contamination from the Galaxy is small. These results represent a new determination of the CMB power spectrum on angular scales where previous results show a large scatter; our new results are in agreement with the theoretical predictions of the standard inflationary cold dark matter models.

astro-ph↗