arXiv subjects

Aapo Varpula

Publications and source records attributed to Aapo Varpula.

7 recordsLinked to original sources

arXiv2025

Far- and near-field photon noise limits to the detectivity of nanometer-thick thermal detectors

Thermal-radiation detectors such as bolometers -- often found as thin, suspended films -- are intrinsically limited by their optical absorption properties and by their intrinsic thermal conductive and radiative losses. We analyze the impact of the photon energy exchange between the film and a substrate located close to each other, noticing that the associated near-field exchange has been overlooked and could reduce the detectivity. In addition, we study how the nanometric thickness of the suspended film and its material impact the detectivity of such sensors. It is found that the blackbody-related photon noise limit of the detectivity can be surpassed with thin films. These results emphasize pathways for improvements of thermal-radiation detectors.

physics.optics↗

arXiv2024

Infrared Bolometers Based on 40-nm-Thick Nano-Thermoelectric Silicon Membranes

State-of the-art infrared photodetectors operating in the mid- and long-wavelength infrared (MWIR and LWIR) are largely dominated by cryogenically cooled quantum sensors when the target is the highest sensitivity and detection speeds. Nano-thermoelectrics provide a route towards competitive uncooled infrared bolometer technology that can obtain high speed and sensitivity, low-power operation, and cost-effectiveness. We demonstrate nano-thermoelectric LWIR bolometers with fast and high-sensitivity response to LWIR around 10 $\mu$m. These devices are based on ultra-thin silicon membranes that utilize the dimensional scaling of silicon nanomembranes in thermoelectric elements and are combined with metallic nanomembranes with subwavelength absorber structures. The fast device performance stems from a low heat capacity design where the thermoelectric beams act both as mechanical supports and transducer elements. Furthermore, by scaling down the thickness of the thermoelectric beams the thermal conductivity is reduced owing to enhanced phonon boundary scattering, resulting in increased sensitivity. The nano-thermoelectric LWIR bolometers are based on 40-nm-thick n- and p-type silicon membranes with LWIR (voltage) responsivities up to 1636 V/W and 1350 V/W and time constants in the range of 300-600 $\mu$s, resulting in specific detectivities up to $1.56\times10^8$ cmHz$^{1/2}$/W. We also investigate the use of a heavily doped N++ substrate to increase optical cavity back reflection, resulting in an increased Si substrate reflectance from 30% to 70%-75% for wavelengths between 8-10 $\mu$m, resulting in an increase in device responsivity by approximately 20%.

physics.optics↗

arXiv2021

Characterization of Predictable Quantum Efficient Detector over a wide range of incident optical power and wavelength

We investigate the Predictable Quantum Efficient Detector (PQED) in the visible and near-infrared wavelength range. The PQED consists of two n-type induced junction photodiodes with $Al_2O_3$ entrance window. Measurements are performed at the wavelengths of 488 nm and 785 nm with incident power levels ranging from 100 $μ$W to 1000 $μ$W. A new way of presenting the normalized photocurrents on a logarithmic scale as a function of bias voltage reveals two distinct negative slope regions and allows direct comparison of charge carrier losses at different wavelengths. The comparison indicates mechanisms that can be understood on the basis of different penetration depths at different wavelengths (0.77 $μ$m at 488 nm and 10.2 $μ$m at 785 nm). The difference in the penetration depths leads also to larger difference in the charge-carrier losses at low bias voltages than at high voltages due to the voltage dependence of the depletion region.

physics.optics↗

arXiv2021

Nano-thermoelectric infrared bolometers

Infrared (IR) radiation detectors are used in numerous applications from thermal imaging to spectroscopic gas sensing. Obtaining high speed and sensitivity, low-power operation and cost-effectiveness with a single technology remains to be a challenge in the field of IR sensors. By combining nano-thermoelectric transduction and nanomembrane photonic absorbers, we demonstrate uncooled IR bolometer technology that is material-compatible with large-scale CMOS fabrication and provides fast and high sensitivity response to long-wavelength IR (LWIR) around 10 $μ$m. The fast operation speed stems from the low heat capacity metal layer grid absorber connecting the sub-100 nm-thick n- and p-type Si nano-thermoelectric support beams, which convert the radiation induced temperature rise into voltage. The nano-thermoelectric transducer-support approach benefits from enhanced phonon surface scattering in the beams leading to reduction in thermal conductivity, which enhances the sensitivity. We demonstrate different size nano-thermoelectric bolometric photodetector pixels with LWIR responsitivities, specific detectivities and time constants in the ranges 179-2930 V/W, 0.15-3.1$\cdot10^{8}$ cmHz$^{1/2}$/W and 66-3600 $μ$s, respectively. We benchmark the technology against different LWIR detector solutions and show how nano-thermoelectric detector technology can reach the fundamental sensitivity limits posed by phonon and photon thermal fluctuation noise.

physics.app-ph↗

arXiv2018

Microfabricated sensor platform with through-glass vias for bidirectional 3-omega thermal characterization of solid and liquid samples

A novel microfabricated, all-electrical measurement platform is presented for a direct, accurate and rapid determination of the thermal conductivity and diffusivity of liquid and solid materials. The measurement approach is based on the bidirectional 3-omega method. The platform is composed of glass substrates on which sensor structures and a very thin dielectric nanolaminate passivation layer are fabricated. Using through-glass vias for contacting the sensors from the chip back side leaves the top side of the platform free for deposition, manipulation and optical inspection of the sample during 3-omega measurements. The thin passivation layer, which is deposited by atomic layer deposition on the platform surface, provides superior chemical resistance and allows for the measurement of electrically conductive samples, while maintaining the conditions for a simple thermal analysis. We demonstrate the measurement of thermal conductivities of borosilicate glass, pure water, glycerol, 2-propanol, PDMS, cured epoxy, and heat-sink compounds. The results compare well with both literature values and values obtained with the steady-state divided bar method. Small sample volumes (~0.02 mm$^2$) suffice for accurate measurements using the platform, allowing rapid temperature-dependent measurements of thermal properties, which can be useful for the development, optimization and quality testing of many materials, such as liquids, gels, pastes and solids.

physics.ins-det↗

arXiv2017

Thermoelectric bolometers based on ultra-thin heavily doped single-crystal silicon membranes

We present ultra-thin silicon membrane thermocouple bolometers suitable for fast and sensitive detection of low levels of thermal power and infrared radiation at room temperature. The devices are based on 40 nm-thick strain tuned single crystalline silicon membranes shaped into heater/absorber area and narrow n- and p-doped beams, which operate as the thermocouple. The electro-thermal characterization of the devices reveal noise equivalent power of 13 pW/rtHz and thermal time constant of 2.5 ms. The high sensitivity of the devices is due to the high Seebeck coefficient of 0.39 mV/K and reduction of thermal conductivity of the Si beams from the bulk value. The bolometers operate in the Johnson-Nyquist noise limit of the thermocouple, and the performance improvement towards the operation close to the temperature fluctuation limit is discussed.

cond-mat.mes-hall↗

arXiv2012

Diffusion-emission theory of photon enhanced thermionic emission solar energy harvesters

Numerical and semi-analytical models are presented for photon-enhanced-thermionic-emission (PETE) devices. The models take diffusion of electrons, inhomogeneous photogeneration, and bulk and surface recombination into account. The efficiencies of PETE devices with silicon cathodes are calculated. Our model predicts significantly different electron affinity and temperature dependence for the device than the earlier model based on a rate-equation description of the cathode. We show that surface recombination can reduce the efficiency below 10% at the cathode temperature of 800 K and the concentration of 1000 suns, but operating the device at high injection levels can increase the efficiency to 15%.

cond-mat.mtrl-sci↗