Searcharxiv⌕ Search

arXiv subjects

Adam Libson

Publications and source records attributed to Adam Libson.

8 recordsLinked to original sources
arXiv2024

Quantum Frequency Mixing using an N-$V$ Diamond Microscope

Wide-field magnetic microscopy using nitrogen-vacancy (NV) centers in diamond can yield high-quality magnetic images of DC and AC magnetic fields. The unique combination of micron-scale spatial resolution of scalar or vector fields at room temperature and parallel camera readout make this an appealing technique for applications in biology, geology, condensed-matter physics, and electronics. However, while NV magnetic microscopy has achieved great success in these areas, historically the accessible frequency range has been limited. In this paper, we overcome this limitation by implementing the recently developed technique of quantum frequency mixing. With this approach, we generate wide-field magnetic images of test structures driven by alternating currents up to 70 MHz, well outside the reach of DC and Rabi magnetometry methods. With further improvements, this approach could find utility in hyperspectral imaging for electronics power spectrum analysis, electronics diagnostics and troubleshooting, and quantum computing hardware validation.

physics.ins-det↗
arXiv2018

Room temperature optomechanical squeezing

The radiation-pressure driven interaction of a coherent light field with a mechanical oscillator induces correlations between the amplitude and phase quadratures of the light. These correlations result in squeezed light -- light with quantum noise lower than shot noise in some quadratures, and higher in others. Due to this lower quantum uncertainty, squeezed light can be used to improve the sensitivity of precision measurements. In particular, squeezed light sources based on nonlinear optical crystals are being used to improve the sensitivity of gravitational wave (GW) detectors. For optomechanical squeezers, thermally driven fluctuations of the mechanical oscillator's position makes it difficult to observe the quantum correlations at room temperature, and at low frequencies. Here we present a measurement of optomechanically (OM) squeezed light, performed at room-temperature, in a broad band near audio-frequency regions relevant to GW detectors. We observe sub-poissonian quantum noise in a frequency band of 30 kHz to 70 kHz with a maximum reduction of 0.7 $\pm$ 0.1 dB below shot noise at 45 kHz. We present two independent methods of measuring this squeezing, one of which does not rely on calibration of shot noise.

quant-ph↗
arXiv2018

Observation of a room-temperature oscillator's motion dominated by quantum fluctuations over a broad audio-frequency band

We report on the broadband measurement of quantum radiation pressure noise (QRPN) in an optomechanical cavity at room temperature over a broad range of frequencies relevant to gravitational-wave detectors. We show that QRPN drives the motion of a high-reflectivity single-crystal microresonator, which serves as one mirror of a Fabry-Perot cavity. In our measurements QRPN dominates over all other noise between 10 kHz and 50 kHz and scales as expected with the circulating power inside the cavity. The thermal noise of the microresonator, the largest noise source next to the QRPN, is measured and shown to agree with a structural damping model from 200 Hz to 30 kHz. By observing the effects of QRPN in the audio-band, we now have a testbed for studying techniques to mitigate back-action, such as variational readout and squeezed light injection, that could be used to improve the sensitivity of gravitational-wave detectors.

quant-ph↗
arXiv2017

Radiation-Pressure-Mediated Control of an Optomechanical Cavity

We describe and demonstrate a method to control a detuned movable-mirror Fabry-Perot cavity using radiation pressure in the presence of a strong optical spring. At frequencies below the optical spring resonance, self-locking of the cavity is achieved intrinsically by the optomechanical (OM) interaction between the cavity field and the movable end mirror. The OM interaction results in a high rigidity and reduced susceptibility of the mirror to external forces. However, due to a finite delay time in the cavity, this enhanced rigidity is accompanied by an anti-damping force, which destabilizes the cavity. The cavity is stabilized by applying external feedback in a frequency band around the optical spring resonance. The error signal is sensed in the amplitude quadrature of the transmitted beam with a photodetector. An amplitude modulator in the input path to the cavity modulates the light intensity to provide the stabilizing radiation pressure force.

quant-ph↗
arXiv2014

Simple method for locking birefringent resonators

We report on a simple method of locking a laser to a birefringent cavity using polarization spectroscopy. The birefringence of the resonator permits the simple extraction of an error signal by using one polarization state as a phase reference for another state. No modulation of the light or the resonator is required, reducing the complexity of the laser locking setup. This method of producing an error signal can be used on most birefringent optical resonators, even if the details of birefringence and eigenpolarizations are not known. This technique is particularly well suited for fiber ring resonators due to the inherent birefringence of the fiber and the unknown nature of that birefringence. We present an experimental demonstration of this technique using a fiber ring.

physics.optics↗
arXiv2010

Nanofabrication by magnetic focusing of supersonic beams

We present a new method for nanoscale atom lithography. We propose the use of a supersonic atomic beam, which provides an extremely high-brightness and cold source of fast atoms. The atoms are to be focused onto a substrate using a thin magnetic film, into which apertures with widths on the order of 100 nm have been etched. Focused spot sizes near or below 10 nm, with focal lengths on the order of 10 microns, are predicted. This scheme is applicable both to precision patterning of surfaces with metastable atomic beams and to direct deposition of material.

physics.atom-ph↗
arXiv2008

Stopping Supersonic Beams with an Atomic Coilgun

We report the stopping of an atomic beam, using a series of pulsed electromagnetic coils. We use a supersonic beam of metastable neon created in a gas discharge as a monochromatic source of paramagnetic atoms. A series of coils is fired in a timed sequence to bring the atoms to near-rest, where they are detected on a micro-channel plate. Applications to fundamental problems in physics and chemistry are discussed.

physics.atom-ph↗