arXiv subjects

Agata Piacentini

Publications and source records attributed to Agata Piacentini.

5 recordsLinked to original sources

arXiv2024

Contact Resistance Optimization in MoS${_2}$ Field-Effect Transistors through Reverse Sputtering-Induced Structural Modifications

Two-dimensional material (2DM)-based field-effect transistors (FETs), such as molybdenum disulfide (MoS${_2}$)-FETs, have gained significant attention for their potential for ultra-short channels, thereby extending Moore's law. However, MoS${_2}$-FETs are prone to the formation of Schottky barriers at the metal-MoS${_2}$ interface, resulting in high contact resistance (R${_c}$) and, consequently, reduced transistor currents in the ON-state. Our study explores the modification of MoS${_2}$ to induce the formation of conductive 1T-MoS${_2}$ at the metal-MoS${_2}$ interface via reverse sputtering. MoS${_2}$-FETs exposed to optimized reverse sputtering conditions in the contact area show R${_c}$ values reduced to less than 50% of their untreated counterparts. This reduction translates into improvements in other electrical characteristics, such as higher ON-state currents. Since reverse sputtering is a standard semiconductor process that enhances the electrical performance of MoS${_2}$-FETs, it has great potential for broader application scenarios in 2DM-based microelectronic devices and circuits.

cond-mat.mtrl-sci↗

arXiv2024

Dry Transfer Based on PMMA and Thermal Release Tape for Heterogeneous Integration of 2D-TMDC Layers

A reliable and scalable transfer of 2D-TMDCs (two-dimensional transition metal dichalcogenides) from the growth substrate to a target substrate with high reproducibility and yield is a crucial step for device integration. In this work, we have introduced a scalable dry-transfer approach for 2D-TMDCs grown by MOCVD (metal-organic chemical vapor deposition) on sapphire. Transfer to a silicon/silicon dioxide (Si/SiO$_2$) substrate is performed using PMMA (poly(methyl methacrylate)) and TRT (thermal release tape) as sacrificial layer and carrier, respectively. Our proposed method ensures a reproducible peel-off from the growth substrate and better preservation of the 2D-TMDC during PMMA removal in solvent, without compromising its adhesion to the target substrate. A comprehensive comparison between the dry method introduced in this work and a standard wet transfer based on potassium hydroxide (KOH) solution shows improvement in terms of cleanliness and structural integrity for dry-transferred layer, as evidenced by X-ray photoemission and Raman spectroscopy, respectively. Moreover, fabricated field-effect transistors (FETs) demonstrate improvements in subthreshold slope, maximum drain current and device-to-device variability. The dry-transfer method developed in this work enables large-area integration of 2D-TMDC layers into (opto)electronic components with high reproducibility, while better preserving the as-grown properties of the layers.

physics.app-ph↗

arXiv2024

Tunable Doping and Mobility Enhancement in 2D Channel Field-Effect Transistors via Damage-Free Atomic Layer Deposition of AlOX Dielectrics

Two-dimensional materials (2DMs) have been widely investigated because of their potential for heterogeneous integration with modern electronics. However, several major challenges remain, such as the deposition of high-quality dielectrics on 2DMs and the tuning of the 2DM doping levels. Here, we report a scalable plasma-enhanced atomic layer deposition (PEALD) process for direct deposition of a nonstoichiometric aluminum oxide (AlOX) dielectric, overcoming the damage issues associated with conventional methods. Furthermore, we control the thickness of the dielectric layer to systematically tune the doping level of 2DMs. The experimental results demonstrate successful deposition without detectable damage, as confirmed by Raman spectroscopy and electrical measurements. Our method enables tuning of the Dirac and threshold voltages of back-gated graphene and MoS${_2}$ field-effect transistors (FETs), respectively, while also increasing the charge carrier mobility in both device types. We further demonstrate the method in top-gated MoS${_2}$ FETs with double-stack dielectric layers (AlOX+Al${_2}$O${_3}$), achieving critical breakdown field strengths of 7 MV/cm and improved mobility compared with the back gate configuration. In summary, we present a PEALD process that offers a scalable and low-damage solution for dielectric deposition on 2DMs, opening new possibilities for precise tuning of device characteristics in heterogeneous electronic circuits.

physics.app-ph↗

arXiv2024

CVD Graphene Contacts for Lateral Heterostructure MoS${_2}$ Field Effect Transistors

Intensive research is carried out on two-dimensional materials, in particular molybdenum disulfide, towards high-performance transistors for integrated circuits. Fabricating transistors with ohmic contacts is challenging due to the high Schottky barrier that severely limits the transistors' performance. Graphene-based heterostructures can be used in addition or as a substitute for unsuitable metals. We present lateral heterostructure transistors made of scalable chemical vapor-deposited molybdenum disulfide and chemical vapor-deposited graphene with low contact resistances of about 9 k$Ω$$μ$m and high on/off current ratios of 10${^8}$. We also present a theoretical model calibrated on our experiments showing further potential for scaling transistors and contact areas into the few nanometers range and the possibility of a strong performance enhancement by means of layer optimizations that would make transistors promising for use in future logic circuits.

cond-mat.mes-hall↗

arXiv2024

Button Shear Testing for Adhesion Measurements of 2D Materials

Two-dimensional (2D) materials are considered for numerous applications in microelectronics, although several challenges remain when integrating them into functional devices. Weak adhesion is one of them, caused by their chemical inertness. Quantifying the adhesion of 2D materials on three-dimensional surfaces is, therefore, an essential step toward reliable 2D device integration. To this end, button shear testing is proposed and demonstrated as a method for evaluating the adhesion of 2D materials with the examples of graphene and hexagonal boron nitride (hBN), molybdenum disulfide, and tungsten diselenide on silicon dioxide (SiO${_2}$) and silicon nitride substrates. We propose a fabrication process flow for polymer buttons on the 2D materials and establish suitable button dimensions and testing shear speeds. We show with our quantitative data that low substrate roughness and oxygen plasma treatments on the substrates before 2D material transfer result in higher shear strengths. Thermal annealing increases the adhesion of hBN on SiO${_2}$ and correlates with the thermal interface resistance between these materials. This establishes button shear testing as a reliable and repeatable method for quantifying adhesion of 2D materials.

physics.app-ph↗