arXiv subjects

Ahmed S. Ibrahim

Publications and source records attributed to Ahmed S. Ibrahim.

10 recordsLinked to original sources

arXiv2022

Impact of Device Thermal Performance on 5G mmWave Communication Systems

5G millimeter wave (mmWave) cellular networks have been reported to deliver 1-2 Gbps downlink throughput, via speed-tests. However, these speed-tests capture only a few seconds of throughput and are not representative of sustained throughput over several minutes. We report the first measurements of sustained throughput in three cities, Miami, Chicago, and San Francisco, where we observe throughput throttling due to rising skin temperature of the phone when it is connected to a deployed 5G mmWave base-station (BS). Radio Resource Control (RRC) messaging between the phone and the BS indicates the reduction in the number of aggregated mmWave channels from 4 to 1 followed by a switch to 4G. We corroborate these measurements with infra-red images as the phone heats up. Thus, mmWave throughput will be limited not by network characteristics but by device thermal management.

cs.NI↗

arXiv2021

A Comparison Study of Cellular Deployments in Chicago and Miami Using Apps on Smartphones

Cellular operators have begun deploying 5G New Radio (NR) in all available bands: low (< 1 GHz), mid (1 - 6 GHz), and high (> 24 GHz) to exploit the different capabilities of each. At the same time, traditional 4G Long Term Evolution (LTE) deployments are being enhanced with the addition of bands in the unlicensed 5 GHz (using License Assisted Access, or LAA) and the 3.5 GHz Citizens Broadband Radio Service (CBRS) resulting in throughput performance comparable to 5G in mid-band. We present a detailed study comparing 4G and 5G deployments, in all bands in Chicago, and focused mmWave measurements and analysis in Miami. Our methodology, based on commercial and custom apps, is scalable for crowdsourcing measurements on a large scale and provides detailed data (throughput, latency, signal strength, etc.) on actual deployments. Our main conclusions based on the measurements are (i) optimized 4G networks in mid-band are comparable in both throughput and latency to current deployments of 5G (both standalone (SA) and non-standalone (NSA)) and (ii) mmWave 5G, even in NSA mode, can deliver multi-Gbps throughput reliably if the installation is dense enough, but performance is still brittle due to the propagation limitations imposed by distance and body loss. Thus, while 5G demonstrates significant early promise, further work needs to be done to ensure that the stated goals of 5G are met.

cs.NI↗

arXiv2021

Geometric Machine Learning for Channel Covariance Estimation in Vehicular Networks

Learning the covariance matrices of spatially-correlated wireless channels, in millimeter-wave (mmWave) vehicular communication, can be utilized in designing environmen-taware beamforming codebooks. Such channel covariance matrices can be represented on non-Euclidean Riemannian manifolds, thanks to their symmetric positive definite (SPD) characteristics. Consequently in this paper, we propose a Riemannian-Geometric machine learning (G-ML) approach for estimating the channel covariance matrices based on unsupervised K-Means model. The proposed K-means algorithm utilizes Log-Euclidean metric (LEM) as the distance measure among channel covariance matrices over the Riemannian manifolds. We show that our proposed K-Means G-ML model can achieve up to 80% less error compared to Euclidean-based K-Means algorithm, which applies clustering on the channel vectors themselves.

eess.SP↗

arXiv2021

A Fast Graph Kernel Based Classification Method for Wireless Link Scheduling on Riemannian Manifold

In this paper, we propose a novel graph kernel method for the wireless link scheduling problem in device-to-device (D2D) networks on Riemannian manifold. The link scheduling problem can be considered as a binary classification problem since each D2D pair can only hold the state active or inactive. Our goal is to learn a novel metric that facilitates the design of an efficient but less computationally demanding machine learning (ML) solution for the binary classification task of link scheduling problem that requires no channel state information (CSI) and a fewer number of training samples as opposed to other benchmark ML algorithms. To this aim, we first represent the wireless D2D network as a graph and model the features of each D2D pair, including its communication and interference links, as regularized (i.e., positively-shifted) Laplacian matrices which are symmetric positive definite (SPD) one. By doing so, we represent the feature information of each D2D pair as a point on the SPD manifold, and we analyze the topology through Riemannian geometry. We compute the Riemannian metric, e.g., Log-Euclidean metric (LEM), which are suitable distance measures between the regularized Laplacian matrices. The LEM is then utilized to define a positive definite graph kernel for the binary classification of the link scheduling decisions. Simulation results demonstrate that the proposed graph Kernel-based method is computationally less demanding and achieves a sum rate of more than 95% of benchmark algorithm FPLinQ [1] for 10 D2D pairs without using CSI and less than a hundred training network layouts.

eess.SP↗

arXiv2021

Wireless Link Scheduling via Interference-aware Symmetric Positive Definite Connectivity Manifolds

In this paper, we investigate the fundamental problem of wireless link scheduling in device-to-device (D2D) networks, through the lens of Riemannian geometry. Our goal is to find a novel metric to characterize interference among D2D pairs, which can pave the way towards efficient and fast scheduling algorithms. Towards achieving this goal, we first model the connectivity pattern of each D2D pair, including its interference links, as a positively-shifted Laplacian matrix, which is a symmetric positive definite (SPD) one. Noting that SPD matrices constitute a non-Euclidean manifold, we represent each of the D2D pairs as a point on the SPD (i.e., conic) manifold, which is analyzed via Riemannian geometry. Accordingly we employ Riemannian metrics (e.g., Log-Euclidean metric "LEM"), which are suitable measures of distances on manifolds, to characterize the interference among D2D points on the SPD manifold. To validate the effectiveness of the proposed LEM-based interference measure, we propose a sequential link selection algorithm that schedules D2D pairs in a descending order of their signal-to-noise ratio (SNR), while keeping their LEM distances towards the already-scheduled pairs on the Riemannian manifold to be greater than a certain LEM threshold. Such LEM-based condition is equivalent to limiting the interference from potential D2D pairs to be below certain threshold. We show that the proposed LEM-based scheduling algorithm achieves sum rate of more than 86% of state-of-the-art ones (e.g., FPLinQ), while only requiring spatial locations of D2D pairs, as opposed to requiring full channel state information (CSI).

eess.SP↗

arXiv2020

Byzantine-Fault-Tolerant Consensus via Reinforcement Learning for Permissioned Blockchain Implemented in a V2X Network

Blockchain has been forming the central piece of various types of vehicle-to-everything (V2X) network for trusted data exchange. Recently, permissioned blockchains garner particular attention thanks to their improved scalability and diverse needs from different organizations. One representative example of permissioned blockchain is Hyperledger Fabric ("Fabric"). Due to its unique execute-order procedure, there is a critical need for a client to select an optimal number of peers. The interesting problem that this paper targets to address is the tradeoff in the number of peers: a too large number will degrade scalability while a too small number will make the network vulnerable to faulty nodes. This optimization issue gets especially challenging in V2X networks due to mobility of nodes: a transaction must be executed and the associated block must be committed before the vehicle leaves a network. To this end, this paper proposes an optimal peers selection mechanism based on reinforcement learning (RL) to keep a Fabric-empowered V2X network impervious to dynamicity due to mobility. We model the RL as a contextual multi-armed bandit (MAB) problem. The results demonstrate the outperformance of the proposed scheme.

cs.NI↗

arXiv2020

Rethinking Maximum Flow Problem and Beamforming Design through Brain-inspired Geometric Lens

Increasing data rate in wireless networks can be accomplished through a two-pronged approach, which are 1) increasing the network flow rate through parallel independent routes and 2) increasing the user's link rate through beamforming codebook adaptation. Mobile relays are utilized to enable achieving these goals given their flexible positioning. First at the network level, we model regularized Laplacian matrices, which are symmetric positive definite (SPD) ones representing relay-dependent network graphs, as points over Riemannian manifolds. Inspired by the geometric classification of different tasks in the brain network, Riemannian metrics, such as Log-Euclidean metric (LEM), are utilized to choose relay positions that result in maximum LEM. Simulation results show that the proposed LEM-based relay positioning algorithm enables parallel routes and achieves maximum network flow rate, as opposed to other metrics (e.g., algebraic connectivity). Second at the link level, we design unique relay-dependent beamforming codebooks aimed to increase data rate over the spatially-correlated fading channels between a given relay and its neighboring users. To do so, we propose a geometric machine learning approach, which utilizes support vector machine (SVM) model to learn an SPD variant of the user's channel over Riemannian manifolds. Consequently, LEM-based Riemannian metric is utilized for classification of different channels, and a matched beamforming codebook is constructed accordingly. Simulation results show that the proposed geometric-based learning model achieves the maximum link rate after a short training period.

eess.SP↗

arXiv2019

Interference Management in UAV-assisted Integrated Access and Backhaul Cellular Networks

An integrated access and backhaul (IAB) network architecture can enable flexible and fast deployment of next-generation cellular networks. However, mutual interference between access and backhaul links, small inter-site distance and spatial dynamics of user distribution pose major challenges in the practical deployment of IAB networks. To tackle these problems, we leverage the flying capabilities of unmanned aerial vehicles (UAVs) as hovering IAB-nodes and propose an interference management algorithm to maximize the overall sum rate of the IAB network. In particular, we jointly optimize the user and base station associations, the downlink power allocations for access and backhaul transmissions, and the spatial configurations of UAVs. We consider two spatial configuration modes of UAVs: distributed UAVs and drone antenna array (DAA), and show how they are intertwined with the spatial distribution of ground users. Our numerical results show that the proposed algorithm achieves an average of $2.9\times$ and $6.7\times$ gains in the received downlink signal-to-interference-plus-noise ratio (SINR) and overall network sum rate, respectively. Finally, the numerical results reveal that UAVs cannot only be used for coverage improvement but also for capacity boosting in IAB cellular networks.

eess.SP↗

arXiv2019

Ray Tracing Analysis for UAV-assisted Integrated Access and Backhaul Millimeter Wave Networks

The use of Millimeter-wave (mmWave) spectrum in cellular communications has recently attracted growing interest to support the expected massive increase in traffic demands. However, the high path-loss at mmWave frequencies poses severe challenges. In this paper, we analyze the potential coverage gains of using unmanned aerial vehicles (UAVs), as hovering relays, in integrated access and backhaul (IAB) mmWave cellular scenarios. Specifically, we utilize the WinProp software package, which employs ray tracing methodology, to study the propagation characteristics of outdoor mmWave channels at 30 and 60 GHz frequency bands in a Manhattan-like environment. In doing so, we propose the implementation of amplify-and-forward (AF) and decode-and-forward (DF) relaying mechanisms in the WinProp software. We show how the 3D deployment of UAVs can be defined based on the coverage ray tracing maps at access and backhaul links. Furthermore, we propose an adaptive UAV transmission power for the AF relaying. We demonstrate, with the aid of ray tracing simulations, the performance gains of the proposed relaying modes in terms of downlink coverage, and the received signal to interference and noise ratio (SINR).

eess.SP↗

arXiv2018

UAV-Based in-band Integrated Access and Backhaul for 5G Communications

We introduce the concept of using unmanned aerial vehicles (UAVs) as drone base stations for in-band Integrated Access and Backhaul (IB-IAB) scenarios for 5G networks. We first present a system model for forward link transmissions in an IB-IAB multi-tier drone cellular network. We then investigate the key challenges of this scenario and propose a framework that utilizes the flying capabilities of the UAVs as the main degree of freedom to find the optimal precoder design for the backhaul links, user-base station association, UAV 3D hovering locations, and power allocations. We discuss how the proposed algorithm can be utilized to optimize the network performance in both large and small scales. Finally, we use an exhaustive search-based solution to demonstrate the performance gains that can be achieved from the presented algorithm in terms of the received signal to interference plus noise ratio (SINR) and overall network sum-rate.

eess.SP↗