SearcharxivSearch

arXiv subjects

Akshay Naik

Publications and source records attributed to Akshay Naik.

15 recordsLinked to original sources

Underwater Dead Reckoning with Deployable Situation-Triggered Covariance Scheduling

Underwater dead reckoning estimates vehicle position when vision is unavailable and external positioning cannot be assumed. A single set of filter parameters can work well in many situations, but fixed tuning may be poorly matched during turns, motion transitions, or periods when sensor measurements are less reliable. This paper presents the Situation-Triggered Calibrated Adaptive Robust Extended Kalman Filter for a BlueROV2. An onboard probabilistic trigger identifies the current motion situation while one error-state filter runs continuously. When the trigger is confident, the filter changes only to the corresponding pre-calibrated process- and measurement-noise matrices; the state estimate, covariance history, dynamics, and measurement models are not reset or replaced. The trigger, noise profiles, and a one-time Doppler velocity log yaw-alignment correction are calibrated offline using sparse AprilTag-supervised pool runs. A separate validation set selects the scheduling policy, which is then fixed before held-out testing. Across four held-out pool runs, the method reduces label-weighted mean per-run translation root-mean-square error from 0.488 m to 0.471 m relative to the same filter backbone with one global noise profile, and every held-out run favors the scheduled method. A paired bootstrap over 10-second segments gives a candidate-minus-baseline difference of -0.017 m with a 95% confidence interval of [-0.024, -0.008] m, while orientation error remains essentially unchanged. These results indicate that situation-aware covariance scheduling provides a modest but consistent vision-free dead-reckoning improvement without switching estimators or resetting the filter.

cs.RO

Nonlinear Mode Coupling in Silicon Nitride Membrane Resonators

Nonlinear interactions between vibrational modes play a crucial role in understanding the dynamical response of nanomechanical resonators. Here, we report the experimental observation and theoretical modeling of nonlinear mode coupling in a high-stress square silicon nitride membrane resonator. We quantify frequency shifts of the fundamental mode arising from tension-mediated geometric nonlinearity by increasing the amplitude of the fundamental mode and higher-order flexural modes. A quantitative theoretical framework based on Kirchhoff-Love plate theory is developed, which incorporates both intrinsic Duffing nonlinearity and nonlinear intermodal coupling and shows good agreement with experimental measurements for the (1,1)-(2,1) and (1,1)-(2,2) mode pairs. We further compute the nonlinear coupling matrix across mode families, revealing the role of mode symmetry and spatial overlap in governing intermodal interactions. These results establish nonlinear mode coupling as a controllable resource for multimode frequency tuning and mechanical transduction.

cond-mat.mes-hall

Gate-tuneable single-photon emitters in WSe2 monolayer created via AFM nanoindentation on rigid SiO2/Si substrates

Single-photon emitters (SPEs) hosted by two-dimensional (2D) semiconducting materials are envisioned for next-generation quantum applications. However, SPE creation in 2D semiconductors on rigid substrates like SiO2/Si via nanoindentation is a technological gap, critical for interfacing SPEs with photonic circuits and cavities. Here, we report a protocol for deterministically creating SPEs in monolayer WSe2 on SiO2/Si substrates using a sharp diamond AFM (atomic force microscope) tip. A displacement-controlled indentation process is developed, allowing indent depths > 150 nm necessary for creating SPEs. Sharp defect peaks (~200 {\mu}eV) are observed in cryogenic (4K) photoluminescence (PL) spectrum at nanoindented sites and are stable upto ~ 120K. 76% of sites exhibit sharp defect-bound peaks confirmed by power-dependent, temperature-dependent, and time-resolved PL (TRPL). AFM and PL mapping link these peaks to indent periphery. The peaks show sub-linewidth spectral jitter, no blinking, and single-photon nature in second-order autocorrelation measurements. SPEs can be switched on/off, and background emissions suppressed using electrical gating. Gate-voltage dependent TRPL indicate that SPE dynamics can be tuned, depending on nature of SPE, pointing the way to higher-purity SPEs. Our work is directly applicable to other 2D materials and photonic circuit/cavity compatible rigid substrates and is a significant step for scalable SPE technologies.

cond-mat.mes-hall

Selective Parametric Amplification of Degenerate Modes in Electrostatically Transduced Coupled Beam Resonators

Parametric excitation in coupled mechanical systems has enabled advances in sensing, computation, and phonon control. The function of distinct phase modes using parametric driving remains insufficiently explored. Here, we investigate the nonlinear and parametric response of degenerate phase modes in a Double Ended Tuning Fork (DETF) resonator. Our measurements reveal pronounced nonlinearity and parametric amplification in the out-phase mode, attributed to the dominant contribution of the coupling beam, while the in-phase mode remains predominantly linear. Uniquely, we demonstrate parametric excitation through the coupling spring, enabling selective amplification and de-amplification controlled via the relative phase between harmonic and parametric drives. A parametric gain of $\sim$13 dB is achieved in the out-phase mode, with phase-dependent modulation of amplification, indicating its suitability for signal processing, logic operations, and memory elements based on degenerate modes. These results establish a new approach to exploiting mode-specific nonlinear dynamics in coupled resonators for emerging applications in sensing and phononic control.

cond-mat.mes-hall

Safety Monitor for Off-Road Planning with Uncertainty Bounded Bekker Costs

Reliable off-road autonomy requires operational constraints so that behavior stays predictable and safe when soil strength is uncertain. This paper presents a runtime assurance safety monitor that collaborates with any planner and uses a Bekker-based cost model with bounded uncertainty. The monitor builds an upper confidence traversal cost from a lightweight pressure sinkage model identified in field tests and checks each planned motion against two limits: maximum sinkage and rollover margin. If the risk of crossing either limit is too high, the monitor switches to a certified fallback that reduces vehicle speed, increases standoff from soft ground, or stops on firmer soil. This separation lets the planner focus on efficiency while the monitor keeps the vehicle within clear safety limits on board. Wheel geometry, wheel load estimate, and a soil raster serve as inputs, which tie safety directly to vehicle design and let the monitor set clear limits on speed, curvature, and stopping at run time. The method carries uncertainty analytically into the upper confidence cost and applies simple intervention rules. Tuning of the sinkage limit, rollover margin, and risk window trades efficiency for caution while keeping the monitor light enough for embedded processors. Results from a simulation environment spanning loam to sand include intervention rates, violation probability, and path efficiency relative to the nominal plan, and a benchtop static loading check provides initial empirical validation.

eess.SY

Hybrid Terrain-Aware Path Planning: Integrating VD-RRT* Exploration and VD-D* Lite Repair

Autonomous ground vehicles operating off-road must plan curvature-feasible paths while accounting for spatially varying soil strength and slope hazards in real time. We present a continuous state--cost metric that combines a Bekker pressure--sinkage model with elevation-derived slope and attitude penalties. The resulting terrain cost field is analytic, bounded, and monotonic in soil modulus and slope, ensuring well-posed discretization and stable updates under sensor noise. This metric is evaluated on a lattice with exact steering primitives: Dubins and Reeds--Shepp motions for differential drive and time-parameterized bicycle arcs for Ackermann steering. Global exploration is performed using Vehicle-Dynamics RRT\(^{*}\), while local repair is managed by Vehicle-Dynamics D\(^{*}\) Lite, enabling millisecond-scale replanning without heuristic smoothing. By separating the terrain--vehicle model from the planner, the framework provides a reusable basis for deterministic, sampling-based, or learning-driven planning in deformable terrain. Hardware trials on an off-road platform demonstrate real-time navigation across soft soil and slope transitions, supporting reliable autonomy in unstructured environments.

cs.RO

Physisorption on Nanomechanical Resonators: The Overlooked Influence of Trace Moisture

Short gas pulses introduced in a vacuum chamber have long been utilized to showcase the ultra-low mass resolutions achievable with nanomechanical resonators. The resonance frequency shifts are used as evidence of gas adsorption. However, there is very little clarity as to what exactly is adsorbing on to the resonators. We demonstrate that the physisorption of gases on cantilevers is predominantly the effect of moisture content that is present even in ultra-high purity gases. The experimental work is performed at low temperatures and in a high vacuum and is supported by theoretical calculations and simulation.

cond-mat.mes-hall

Anisotropic In-plane Thermal Conductivity of Freestanding Few-layer ReS2

Rhenium disulfide (ReS2) is a low-symmetry transition metal dichalcogenide (TMDC) exhibiting strong in-plane anisotropy, weak interlayer coupling, and stacking-dependent physical properties. While anisotropic thermal conductivity has been reported in bulk ReS2, experimental studies on stackingdependent thermal conductivity and its thickness evolution in the few-layer regime remain largely unexplored. Here, we have extracted the thermal conductivity of freestanding, few-layer ReS2 samples (thickness < 10 nm) using polarization-resolved optothermal Raman thermometry after correcting for polarization dependent absorbance. All measured ReS2 samples show pronounced in-plane anisotropic thermal conductivity. Notably, the ~3.5 nm AA-stacked flake shows higher thermal conductivity than the AB-stacked flake of the same thickness, highlighting the influence of stacking order on phonon transport. The in-plane thermal conductivity displays a non-monotonic dependence on thickness over the 2.5 to 8 nm range which is supported by density functional theory (DFT) calculations. These findings provide key insight into anisotropic phonon transport in low-symmetry 2D materials and highlight the potential of few-layer ReS2 for nanoscale thermal management and thermoelectric applications.

cond-mat.mes-hall

Quantum light generation with ultra-high spatial resolution in 2D semiconductors via ultra-low energy electron irradiation

Single photon emitters (SPEs) are building blocks of quantum technologies. Defect engineering of 2D materials is ideal to fabricate SPEs, wherein spatially deterministic and quality-preserving fabrication methods are critical for integration into quantum devices and cavities. Existing methods use combination of strain and electron irradiation, or ion irradiation, which make fabrication complex, and limited by surrounding lattice damage. Here, we utilise only ultra-low energy electron beam irradiation (5 keV) to create dilute defect density in hBN-encapsulated monolayer MoS2, with ultra-high spatial resolution (< 50 nm, extendable to 10 nm). Cryogenic photoluminescence spectra exhibit sharp defect peaks, following power-law for finite density of single defects, and characteristic Zeeman splitting for MoS2 defect complexes. The sharp peaks have low spectral jitter (< 200 {\mu}eV), and are tuneable with gate-voltage and electron beam energy. Use of low-momentum electron irradiation, ease of processing, and high spatial resolution, will disrupt deterministic creation of high-quality SPEs.

cond-mat.mes-hall

Graphene Resonant Pressure Sensor with Ultrahigh Responsivity

Graphene has good mechanical properties including large Young's modulus, making it ideal for many resonant sensing applications. Nonetheless, the development of graphene based sensors has been limited due to difficulties in fabrication, encapsulation, and packaging. Here we report a graphene nanoresonator based resonant pressure sensor. The graphene nano resonator is fabricated on a thin silicon diaphragm that deforms due to pressure differential across it. The deformation-induced strain change results in a resonance frequency shift of the graphene nano resonator. The pressure sensing experiments demonstrate a record high responsivity of 20Hz/Pa with a resolution of 90Pa. The resolution of the sensing scheme is 0.003% of the full-scale range of the pressure sensor. This exceptional performance is attributed to two factors: maintaining a high-quality vacuum environment for the nanoresonator and introducing stimuli through a thin silicon diaphragm. The proposed pressure sensor design provides flexibility to adjust responsivity and range as needed. The fabrication method is simple and has the potential to be integrated with standard CMOS fabrication. The innovative substrate packaging allows the coupling of the resonator's strain with pressure.

physics.app-ph

Mixed Nonlinear Response and Transition of Nonlinearity in a Piezoelectric Membrane

Nonlinearities play a critical role in the dynamics of mechanical resonators, enhancing sensitivity and enabling signal manipulation. Understanding the parameters affecting nonlinearities is crucial for developing strategies to counteract their effects or manipulate them for improved device performance. This study investigates the impact of fabrication-induced curvature on the dynamics of zinc oxide-based piezoelectric micromachined ultrasonic transducers (PMUTs). Our experiments reveal that these devices exhibit hardening, softening, and mixed nonlinear responses, with varying initial static displacements. Notably, PMUTs with almost flat initial static displacement exhibit hardening nonlinearity, while those with a curved initial static displacement show softening nonlinearity. An exotic mixed nonlinear response is observed for intermediate static displacement. We attribute the observed nonlinear response to the interplay between static displacement-induced quadratic nonlinearity and midplane stretching-induced cubic nonlinearity. We provide a theoretical formulation for the dynamics of the devices, which explains the experimental results and highlights the nonlinear responses and their dependence on the initial static displacement. Our findings underscore the significance of nonlinearities in the dynamics of mechanical resonators and suggest ways to optimize device performance.

physics.app-ph

Nanomechanical Resonators: Toward Atomic Scale

The quest for realizing and manipulating ever smaller man-made movable structures and dynamical machines has spurred tremendous endeavors, led to important discoveries, and inspired researchers to venture to new grounds. Scientific feats and technological milestones of miniaturization of mechanical structures have been widely accomplished by advances in machining and sculpturing ever shrinking features out of bulk materials such as silicon. With the flourishing multidisciplinary field of low-dimensional nanomaterials, including one-dimensional (1D) nanowires/nanotubes, and two-dimensional (2D) atomic layers such as graphene/phosphorene, growing interests and sustained efforts have been devoted to creating mechanical devices toward the ultimate limit of miniaturization--genuinely down to the molecular or even atomic scale. These ultrasmall movable structures, particularly nanomechanical resonators that exploit the vibratory motion in these 1D and 2D nano-to-atomic-scale structures, offer exceptional device-level attributes, such as ultralow mass, ultrawide frequency tuning range, broad dynamic range, and ultralow power consumption, thus holding strong promises for both fundamental studies and engineering applications. In this Review, we offer a comprehensive overview and summary of this vibrant field, present the state-of-the-art devices and evaluate their specifications and performance, outline important achievements, and postulate future directions for studying these miniscule yet intriguing molecular-scale machines.

cond-mat.mes-hall

Two-dimensional ReS2: Solution to the Unresolved Queries on Its Structure and Inter-layer Coupling Leading to Potential Optical Applications

Over the last few years, ReS2 has generated a myriad of unattended queries regarding its structure, the concomitant thickness dependent electronic properties and apparently contrasting experimental optical response. In this work, with elaborate first-principles investigations, using density functional theory (DFT) and time-dependent DFT (TDDFT), we identify the structure of ReS2, which is capable of reproducing and analyzing the layer-dependent optical response. The theoretical results are further validated by an in-depth structural, chemical, optical and optoelectronic analysis of the large-area ReS2 thin films, grown by chemical vapor deposition (CVD) process. Micro-Raman (MR), X-ray photoelectron spectroscopy (XPS), cross-sectional transmission electron microscopy (TEM) and energy-dispersive X-ray analysis (EDAX) have enabled the optimization of the uniform growth of the CVD films. The correlation between the layer-dependent optical and electronic properties of the excited states was established by static photoluminescence (PL) and transient absorption (TA) measurements. Sulfur vacancy-induced localized mid-gap states render a significantly long life-time of the excitons in these films. The ionic gel top-gated photo-detectors, fabricated from the as-prepared CVD films, exhibit a large photo-response of ~ 5 A/W and a remarkable detectivity of ~ 1011 Jones. The outcome of the present work will be useful to promote the application of vertically grown large-area films in the field of optics and opto-electronics.

cond-mat.mtrl-sci

Combinatorial Large-area MoS2/Anatase-TiO2 interface: A Pathway to Emergent Optical and Opto-electronic Functionalities

Interface of transition metal dichalcogenide (TMDC) and high-k dielectric transition metal oxides (TMO) had triggerred umpteen discourses due to the indubitable impact of TMO in reducing the contact resistances and restraining the Fermi-level pinning for the metal-TMDC contacts. In the present work, we focus on the unresolved tumults of large-area TMDC/TMO interfaces, grown by adopting different techniques. Here, on a pulsed laser deposited (PLD) MoS2 thin film, a layer of TiO2 is grown by using both atomic layer deposition (ALD) and PLD. These two different techniques emanate TiO2 layers with different crystalline properties, thicknesses and interfacial morphologies, subsequently influencing the electronic and optical properties of the interfaces. In addition, they manifest a boost in the extent of p-type doping with increasing thickness of TiO2, as emerged after analyzing the core-level shifts of the X-ray photoelectron spectra (XPS). Density functional analysis of the MoS2/Anatase-TiO2 interfaces, for pristine and in presence of a wide range of interfacial defects, could explain the interdependence of doping and the terminating atomic-surface of TiO2 on MoS2. The optical properties of the interface, encompassing the photoluminescence, transient absorption and z-scan two-photon absorption indicate the presence of defect-induced localized mid-gap levels in MoS2/TiO2 (PLD), resulting quenched exciton signals. On the contrary, the relatively defect-free interface in MoS2/TiO2 (ALD) demonstrates a clear presence of both A and B excitons of MoS2. From the investigation of optical properties, we indicate that MoS2/TiO2 (PLD) interface may act as a promising saturable absorber. Moreover, MoS2/TiO2 (PLD) interface had resulted a better photo-transport. A potential application of MoS2/TiO2 (PLD) is demonstrated by the fabrication of a p-type photo-transistor with the ionic-gel top gate.

cond-mat.mtrl-sci

Open-Source Matlab-Based Graphical User Interface (GUI) For Computer Control of Microscopes Using Micro-Manager

Live time-lapse microscopy is essential for a wide range of biological applications. Software-based automation is the gold standard for the operation of hardware accessories necessary for image acquisition. Given that current software packages are neither affordable nor open to complex structured programming, we have developed a Matlab-based graphical user interface (GUI) that is fundamentally accessible while providing limitless avenues for further customization. The GUI simultaneously communicates with the open-source, cross-functional platform micro-Manager for controlling hardware for time-lapse image acquisition and with other software for image processing. The use of the GUI is demonstrated through an 18-hour cell migration experiment. The results suggest that the GUI can generate high-quality, high-throughput time-lapse images. The core code behind the GUI is open-source so that it can be modified and upgraded. Therefore, it benefits the researchers worldwide by providing them a fundamental yet functional template to add in advanced features specific to their needs, such as additional non-microscopy hardware parts and software packages supported by the Matlab software.

eess.IV