arXiv subjects

Alisa Davydova

Publications and source records attributed to Alisa Davydova.

3 recordsLinked to original sources

arXiv2024

An ultra-broadband photonic-chip-based traveling-wave parametric amplifier

Optical amplification, crucial for modern communication and data center interconnects, primarily relies on erbium-doped fiber amplifiers (EDFAs) to enhance signals without distortion. While EDFAs were historically decisive for the introduction of dense wavelength-division multiplexing, they only cover a portion of the low-loss spectrum of optical fibers. Pioneering work on optical traveling-wave parametric amplifiers (TWPAs) utilizing intrinsic third-order optical nonlinearity has led to demonstrations of increased channel capacity and performance. TWPAs are unidirectional, offer high gain, and can reach the 3-dB quantum limit for phase-preserving amplifiers. Despite the use of highly nonlinear fibers or bulk waveguides, their power requirements and technical complexity have impeded adoption. In contrast, TWPAs based on photonic integrated circuits (PICs) offer the advantages of substantially increased mode confinement and optical nonlinearity but have been limited in bandwidth because of the trade-off with maintaining low propagation loss. We overcome this challenge by using low-loss gallium phosphide-on-silicon dioxide PICs and attain up to 35~dB of parametric gain with waveguides only a few centimeters long in a compact footprint of 0.25 square millimeters. Fiber-to-fiber net gain exceeding 10 dB across a bandwidth of approximately 140 nm is achieved, surpassing the gain window of a standard C-band EDFA. We furthermore demonstrate the capability to handle weak signals; input powers can range over six orders of magnitude while maintaining a low noise figure. We exploit these performance characteristics to amplify both optical frequency combs and coherent communication signals. This marks the first ultra-broadband, high-gain, continuous-wave amplification in a PIC, opening up new capabilities for next-generation optical communication, metrology, and sensing.

physics.optics↗

arXiv2023

Lithium tantalate electro-optical photonic integrated circuits for high volume manufacturing

Photonic integrated circuits based on Lithium Niobate have demonstrated the vast capabilities afforded by material with a high Pockels coefficient, allowing linear and high-speed modulators operating at CMOS voltage levels for applications ranging from data-center communications and photonic accelerators for AI. However despite major progress, the industrial adoption of this technology is compounded by the high cost per wafer. Here we overcome this challenge and demonstrate a photonic platform that satisfies the dichotomy of allowing scalable manufacturing at low cost, while at the same time exhibiting equal, and superior properties to those of Lithium Niobate. We demonstrate that it is possible to manufacture low loss photonic integrated circuits using Lithium Tantalate, a material that is already commercially adopted for acoustic filters in 5G and 6G. We show that LiTaO3 posses equally attractive optical properties and can be etched with high precision and negligible residues using DUV lithography, diamond like carbon (DLC) as a hard mask and alkaline wet etching. Using this approach we demonstrate microresonators with an intrinsic cavity linewidth of 26.8 MHz, corresponding to a linear loss of 5.6 dB/m and demonstrate a Mach Zehnder modulator with Vpi L = 4.2 V cm half-wave voltage length product. In comparison to Lithium Niobate, the photonic integrated circuits based on LiTaO3 exhibit a much lower birefringence, allowing high-density circuits and broadband operation over all telecommunication bands (O to L band), exhibit higher photorefractive damage threshold, and lower microwave loss tangent. Moreover, we show that the platform supports generation of soliton microcombs in X-Cut LiTaO3 racetrack microresonator with electronically detectable repetition rate, i.e. 30.1 GHz.

physics.optics↗

arXiv2023

Soliton Microcomb Generation in a III-V Photonic Crystal Cavity

Photonic crystals, material structures in which the dielectric function varies periodically in one, two, or three dimensions, can provide exquisite control over the propagation and confinement of light. By tailoring their band structure, exceptional optical effects can be achieved, such as slow light propagation or, through the creation of photonic bandgaps, optical cavities with both a high quality factor and a small mode volume. Photonic crystal cavities have been used to realize compact nano-lasers and achieve strong coupling to quantum emitters, such as semiconductor quantum dots, color centers, or cold atoms. A useful attribute of photonic crystals is the ability to create chirped mirrors. Chirping has underpinned advances in ultra-fast lasers based on bulk mirrors, but has yet to be fully exploited in integrated photonics, where it could provide a means to engineer otherwise unattainable dispersion profiles for a range of nonlinear optical applications, including soliton frequency comb generation. The vast majority of integrated resonators for frequency combs make use of microring geometries, where only waveguide width and height are varied to engineer dispersion. Generation of frequency combs has been demonstrated with one-dimensional photonic crystal cavities made of silicon nitride, but the low index contrast prevents formation of broad soliton combs. We overcome these challenges by using a photonic-crystal Fabry-P\'erot resonator made of gallium phosphide, a material with a high refractive index and a Kerr nonlinearity 200 times larger than that of silicon nitride. We employ chirped photonic crystal mirrors to provide anomalous dispersion. With subharmonic pulsed pumping at an average power of 23.6 mW, we are able to access stable dissipative Kerr frequency combs. We demonstrate soliton formation with a 3-dB bandwidth of 3.0 THz, corresponding to a pulse duration of 60 fs.

physics.optics↗