arXiv subjects

Andrew A. Houck

Publications and source records attributed to Andrew A. Houck.

At least 19 recordsLinked to original sources

arXiv2026

Quantifying surface losses in superconducting aluminum microwave resonators

The recent realization of millisecond-scale coherence with tantalum-on-silicon transmon qubits showed that depositing the Al/AlOx/Al Josephson junction in a high purity, ultrahigh vacuum environment was critical for achieving lifetime-limited coherence, motivating careful examination of the aluminum surface two-level system (TLS) bath. Here, we measure the microwave absorption arising from surface TLSs in superconducting aluminum resonators, following methodology developed for tantalum resonators. We vary film and surface properties and correlate microwave measurements with materials characterization. We find that the lifetimes of superconducting aluminum resonators are primarily limited by surface losses associated with TLSs in the 2.7 nm-thick native AlOx. Treatment with 49% HF removes surface AlOx completely; however, rapid oxide regrowth limits improvements in surface loss and long term device stability. Using these measurements we estimate that TLSs in aluminum interfaces contribute around 27% of the relaxation rate of state-of-the-art tantalum-on-silicon qubits that incorporate aluminum-based Josephson junctions.

quant-ph↗

arXiv2026

Beta Tantalum Transmon Qubits with Quality Factors Approaching 10 Million

Tantalum-based transmon qubits are a promising platform for building large-scale quantum processors. So far, these qubits have been made from tantalum films grown exclusively in the alpha phase (α-Ta). The beta phase of tantalum (\{beta}-Ta) readily nucleates at room temperature, making it attractive for scalable qubit fabrication. However, \{beta}-Ta is widely believed to be detrimental to qubit performance because it has a lower superconducting critical temperature than α-Ta. We challenge this prevailing belief by fabricating low-loss transmon qubits from \{beta}-Ta films on sapphire. Across 11 qubits, the mean time-averaged quality factor is (5.6 +/- 2.3) x 10^6, with the best qubit recording a time-averaged quality factor of (10.1 +/- 1.3) x 10^6. Resonator studies demonstrate that the dominant microwave loss channel is surface two-level systems, with the surface loss contribution for \{beta}-Ta being about twice that of α-Ta. \{beta}-Ta films exhibit significant kinetic inductance, consistent with an estimated magnetic penetration depth of (1.78 +/- 0.02) μm. This work establishes \{beta}-Ta on sapphire as a material platform for realizing low-loss transmon qubits and other superconducting devices such as compact resonators, kinetic inductance detectors, and quasiparticle traps.

quant-ph↗

arXiv2026

Chiral and bond-ordered phases in a triangular-ladder superconducting-qubit quantum simulator

Many-body systems with strong interactions often exhibit macroscopic behavior markedly absent in single-particle or noninteracting limits. Such emergent phenomena are well exemplified in lattice Hubbard models, where the interplay between interactions, geometric frustration, and magnetic flux gives rise to rich physics. Superconducting qubits naturally enable analog quantum simulation of Bose-Hubbard models, while offering tunable parameters, site-resolved control, and rapid experimental repetition rates. Here, we study a superconducting-qubit device that realizes the Bose-Hubbard model on a triangular-ladder lattice. By tuning the magnitude and sign of couplings, we engineer a synthetic magnetic flux to characterize the resulting half-filling ground state for various parameter regimes. We measure observables analogous to current-current correlators and bond kinetic energies, finding signatures consistent with chiral superfluids, Meissner superfluids, and bond-ordered insulators. Our results establish superconducting circuits as a platform for robustly probing quantum phases of matter in frustrated Bose-Hubbard systems, even in strongly correlated and gapless regimes.

quant-ph↗

arXiv2025

Superconducting Gap Engineering in Tantalum-Alloy-Based Resonators

Utilizing tantalum (Ta) in superconducting circuits has led to significant improvements, such as high qubit lifetimes and quality factors in both qubits and resonators, underscoring the importance of material optimization in quantum device performance. In this work, we explore superconducting gap engineering in Ta-based devices as a strategy to expand the range of viable host materials. By alloying 20 atomic percent hafnium (Hf) into Ta thin films, we achieve a superconducting transition temperature ($T_c$) of 6.09~K, as measured by DC transport, reflecting an increased superconducting gap. We systematically vary deposition conditions to control film orientation and transport properties of the Ta-Hf alloy films. The enhancement in $T_c$ is further confirmed by microwave measurements at millikelvin temperatures. Despite the 40\% increase in $T_c$ relative to pure Ta, the loss contributions from two-level systems (TLS) and quasiparticles (QPs) remain unchanged in the low-temperature regime. These findings highlight the potential of material engineering to improve superconducting circuit performance and motivate further exploration of engineered alloys for quantum technologies.

quant-ph↗

arXiv2025

Glued tree lattices with only compact localized states

Flat band physics is a central theme in modern condensed matter physics. By constructing a tight--binding single particle system that has vanishing momentum dispersion in one or more bands, and subsequently including more particles and interactions, it is possible to study physics in strongly interacting regimes. Inspired by the glued trees that first arose in one of the few known examples of quantum supremacy, we define and analyze two infinite families of tight binding single particle Bose--Hubbard models that have only flat bands, and only compact localized states despite having any nonnegative number of translation symmetries. The first class of model that we introduce is constructed by replacing a sufficiently large fraction of the edges in a generic countable graph with glued trees modified to have complex hoppings. The second class arises from thinking of complex weighted glued trees as rhombi that can then be used to tile two dimensional space, giving rise to the familiar dice lattice and infinitely many generalizations thereof, of which some are Euclidian while others are hyperbolic.

math-ph↗

arXiv2025

2D transmons with lifetimes and coherence times exceeding 1 millisecond

Materials improvements are a powerful approach to reducing loss and decoherence in superconducting qubits because such improvements can be readily translated to large scale processors. Recent work improved transmon coherence by utilizing tantalum (Ta) as a base layer and sapphire as a substrate. The losses in these devices are dominated by two-level systems (TLSs) with comparable contributions from both the surface and bulk dielectrics, indicating that both must be tackled to achieve major improvements in the state of the art. Here we show that replacing the substrate with high-resistivity silicon (Si) dramatically decreases the bulk substrate loss, enabling 2D transmons with time-averaged quality factors (Q) exceeding 1.5 x 10^7, reaching a maximum Q of 2.5 x 10^7, corresponding to a lifetime (T_1) of up to 1.68 ms. This low loss allows us to observe decoherence effects related to the Josephson junction, and we use improved, low-contamination junction deposition to achieve Hahn echo coherence times (T_2E) exceeding T_1. We achieve these material improvements without any modifications to the qubit architecture, allowing us to readily incorporate standard quantum control gates. We demonstrate single qubit gates with 99.994% fidelity. The Ta-on-Si platform comprises a simple material stack that can potentially be fabricated at wafer scale, and therefore can be readily translated to large-scale quantum processors.

quant-ph↗

arXiv2025

Sub-resonant wideband superconducting Purcell filters

In superconducting quantum devices, Purcell filters protect qubit information from decaying into external lines by reducing external coupling at qubit frequencies while maintaining it at readout frequencies. Here, we introduce and demonstrate a novel Purcell filter design that places the readout resonator frequencies in a "linewidth plateau" below the filter's first resonant mode. This approach, based on direct admittance engineering, can simultaneously achieve strong qubit protection and nearly constant external coupling across a wide readout bandwidth, addressing the traditional tradeoff between these properties. We first present a lumped-element analysis of our filters. We then experimentally demonstrate a compact on-chip linewidth-plateau filter, coupled to four resonators across its approximately 1 GHz readout band. We compare the measured linewidths to numerical predictions, and show how the filter protects a frequency-tunable transmon qubit from external decay. We envision that our flexible design paradigm will aid in efforts to create multiplexed readout architectures for superconducting quantum circuits, with well-controlled external couplings.

quant-ph↗

arXiv2025

Vortex Motion Induced Losses in Tantalum Resonators

Tantalum (Ta) based superconducting circuits have been demonstrated to enable record qubit coherence times and quality factors, motivating a careful study of the microscopic origin of the remaining losses that limit their performance. We have recently shown that the losses in Ta-based resonators are dominated by two-level systems (TLSs) at low microwave powers and millikelvin temperatures. We also observe that some devices exhibit loss that is exponentially activated at a lower temperature inconsistent with the superconducting critical temperature (Tc) of the constituent film. Specifically, dc resistivity measurements show a Tc of over 4 K, while microwave measurements of resonators fabricated from these films show losses that increase exponentially with temperature with an activation energy as low as 0.3 K. Here, we present a comparative study of the structural and thermodynamic properties of Ta-based resonators and identify vortex motion-induced loss as the source of thermally activated microwave loss. Through careful magnetoresistance and x-ray diffraction measurements, we observe that the increased loss occurs for films that are in the clean limit, where the superconducting coherence length is shorter than the mean free path. Vortex motion-induced losses are suppressed for films in the dirty limit, which show evidence of structural defects that can pin vortices. We verify this hypothesis by explicitly pinning vortices via patterning and find that we can suppress the loss by microfabrication.

cond-mat.supr-con↗

arXiv2024

Reciprocal lumped-element superconducting circuits: quantization, decomposition, and model extraction

In this work, we introduce new methods for the quantization, decomposition, and extraction (from electromagnetic simulations) of lumped-element circuit models for superconducting quantum devices. Our flux-charge symmetric procedures center on the network matrix, which encodes the connectivity of a circuit's inductive loops and capacitive nodes. First, we use the network matrix to demonstrate a simple algorithm for circuit quantization, giving novel predictions for the Hamiltonians of circuits with both Josephson junctions and quantum phase slip wires. We then show that by performing pivoting operations on the network matrix, we can decompose a superconducting circuit model into its simplest equivalent "fundamental" form, in which the harmonic degrees of freedom are separated out from the Josephson junctions and phase slip wires. Finally, we illustrate how to extract an exact, transformerless circuit model from electromagnetic simulations of a device's hybrid admittance/impedance response matrix, by matching the lumped circuit's network matrix to the network topology of the physical layout. Overall, we provide a toolkit of intuitive methods that can be used to construct, analyze, and manipulate superconducting circuit models.

quant-ph↗

arXiv2024

Protomon: A Multimode Qubit in the Fluxonium Molecule

Qubits that are intrinsically insensitive to depolarization and dephasing errors promise to significantly reduce the overhead of fault-tolerant quantum computing. At their optimal operating points, the logical states of these qubits exhibit both exponentially suppressed matrix elements and sweet spots in energy dispersion, rendering the qubits immune to depolarization and dephasing, respectively. We introduce a multimode qubit, the protomon, encoded in a fluxonium molecule circuit. Compared to the closely related $0$-$π$ qubit, the protomon offers several advantages in theory: resilience to circuit parameter disorder, minimal dephasing from intrinsic harmonic modes, and no dependence on static offset charge. As a proof of concept, we realize four protomon qubits. By tuning the qubits to various operating points identified with calibrated two-tone spectroscopy, we measure depolarization times ranging from 64 to 73 $μ$s and dephasing times between 0.2 to 0.5 $μ$s for one selected qubit. The discrepancy between the relatively short measured coherence times and theoretical predictions is not fully understood. This calls for future studies investigating the limiting noise factors, informing the direction for improving coherence times of the protomon qubit.

quant-ph↗

arXiv2024

Eliminating Surface Oxides of Superconducting Circuits with Noble Metal Encapsulation

The lifetime of superconducting qubits is limited by dielectric loss, and a major source of dielectric loss is the native oxide present at the surface of the superconducting metal. Specifically, tantalum-based superconducting qubits have been demonstrated with record lifetimes, but a major source of loss is the presence of two-level systems (TLSs) in the surface tantalum oxide. Here, we demonstrate a strategy for avoiding oxide formation by encapsulating the tantalum with noble metals that do not form native oxide. By depositing a few nanometers of Au or AuPd alloy before breaking vacuum, we completely suppress tantalum oxide formation. Microwave loss measurements of superconducting resonators reveal that the noble metal is proximitized, with a superconducting gap over 80% of the bare tantalum at thicknesses where the oxide is fully suppressed. We find that losses in resonators fabricated by subtractive etching are dominated by oxides on the sidewalls, suggesting total surface encapsulation by additive fabrication as a promising strategy for eliminating surface oxide TLS loss in superconducting qubits.

cond-mat.supr-con↗

arXiv2024

Ultrastrong light-matter interaction in a multimode photonic crystal

Harnessing the interaction between light and matter at the quantum level has been a central theme in atomic physics and quantum optics, with applications from quantum computation to quantum metrology. Combining complex interactions with photonic synthetic materials provides an opportunity to investigate novel quantum phases and phenomena, establishing interesting connections to condensed matter physics. Here we explore many-body phenomena with a single artificial atom coupled to the many discrete modes of a photonic crystal. This experiment reaches the ultrastrong light-matter coupling regime using the circuit quantum electrodynamics paradigm, by galvanically coupling a highly nonlinear fluxonium qubit to a tight-binding lattice of microwave resonators. In this regime, the transport of a single photon becomes a many-body problem, owing to the strong participation of multi-photon bound states arising from interactions that break particle number conservation. Exploiting the effective photon-photon interactions mediated by the qubit, the transport of multiple photons leads to complex multimode dynamics that can be employed for generating a continuous reservoir of strongly-correlated photons, an important resource for quantum networks. This work opens exciting prospects for exploring nonlinear quantum optics at the single-photon level and stabilizing entangled many-body phases of light.

quant-ph↗

arXiv2023

Co-Designed Superconducting Architecture for Lattice Surgery of Surface Codes with Quantum Interface Routing Card

Facilitating the ability to achieve logical qubit error rates below physical qubit error rates, error correction is anticipated to play an important role in scaling quantum computers. While many algorithms require millions of physical qubits to be executed with error correction, current superconducting qubit systems contain only hundreds of physical qubits. One of the most promising codes on the superconducting qubit platform is the surface code, requiring a realistically attainable error threshold and the ability to perform universal fault-tolerant quantum computing with local operations via lattice surgery and magic state injection. Surface code architectures easily generalize to single-chip planar layouts, however space and control hardware constraints point to limits on the number of qubits that can fit on one chip. Additionally, the planar routing on single-chip architectures leads to serialization of commuting gates and strain on classical decoding caused by large ancilla patches. A distributed multi-chip architecture utilizing the surface code can potentially solve these problems if one can optimize inter-chip gates, manage collisions in networking between chips, and minimize routing hardware costs. We propose QuIRC, a superconducting Quantum Interface Routing Card for Lattice Surgery between surface code modules inside of a single dilution refrigerator. QuIRC improves scaling by allowing connection of many modules, increases ancilla connectivity of surface code lattices, and offers improved transpilation of Pauli-based surface code circuits. QuIRC employs in-situ Entangled Pair (EP) generation protocols for communication. We explore potential topological layouts of QuIRC based on superconducting hardware fabrication constraints, and demonstrate reductions in ancilla patch size by up to 77.8%, and in layer transpilation size by 51.9% when compared to the single-chip case.

quant-ph↗

arXiv2023

Tunable inductive coupler for high fidelity gates between fluxonium qubits

The fluxonium qubit is a promising candidate for quantum computation due to its long coherence times and large anharmonicity. We present a tunable coupler that realizes strong inductive coupling between two heavy-fluxonium qubits, each with $\sim50$MHz frequencies and $\sim5$ GHz anharmonicities. The coupler enables the qubits to have a large tuning range of $\textit{XX}$ coupling strengths ($-35$ to $75$ MHz). The $\textit{ZZ}$ coupling strength is $<3$kHz across the entire coupler bias range, and $<100$Hz at the coupler off-position. These qualities lead to fast, high-fidelity single- and two-qubit gates. By driving at the difference frequency of the two qubits, we realize a $\sqrt{i\mathrm{SWAP}}$ gate in $258$ns with fidelity $99.72\%$, and by driving at the sum frequency of the two qubits, we achieve a $\sqrt{b\mathrm{SWAP}}$ gate in $102$ns with fidelity $99.91\%$. This latter gate is only 5 qubit Larmor periods in length. We run cross-entropy benchmarking for over $20$ consecutive hours and measure stable gate fidelities, with $\sqrt{b\mathrm{SWAP}}$ drift ($2 σ$) $< 0.02\%$ and $\sqrt{i\mathrm{SWAP}}$ drift $< 0.08\%$.

quant-ph↗

arXiv2023

Flat-band localization and interaction-induced delocalization of photons

Advances in quantum engineering have enabled the design, measurement, and precise control of synthetic condensed matter systems. The platform of superconducting circuits offers two particular capabilities: flexible connectivity of circuit elements that enables a variety of lattice geometries, and circuit nonlinearity that provides access to strongly interacting physics. Separately, these features have allowed for the creation of curved-space lattices and the realization of strongly correlated phases and dynamics in one-dimensional chains and square lattices. Missing in this suite of simulations is the simultaneous integration of interacting particles into lattices with unique band dispersions, such as dispersionless flat bands. An ideal building block for flat-band physics is the Aharonov-Bohm cage: a single plaquette of a lattice whose band structure consists entirely of flat bands. Here, we experimentally construct an Aharonov-Bohm cage and observe the localization of a single photon, the hallmark of all-bands-flat physics. Upon placing an interaction-bound photon pair into the cage, we see a delocalized walk indicating an escape from Aharonov-Bohm caging. We further find that a variation of caging persists for two particles initialized on opposite sites of the cage. These results mark the first experimental observation of a quantum walk that becomes delocalized due to interactions and establish superconducting circuits for studies of flat-band-lattice dynamics with strong interactions.

quant-ph↗

arXiv2023

Microarchitectures for Heterogeneous Superconducting Quantum Computers

Noisy Intermediate-Scale Quantum Computing (NISQ) has dominated headlines in recent years, with the longer-term vision of Fault-Tolerant Quantum Computation (FTQC) offering significant potential albeit at currently intractable resource costs and quantum error correction (QEC) overheads. For problems of interest, FTQC will require millions of physical qubits with long coherence times, high-fidelity gates, and compact sizes to surpass classical systems. Just as heterogeneous specialization has offered scaling benefits in classical computing, it is likewise gaining interest in FTQC. However, systematic use of heterogeneity in either hardware or software elements of FTQC systems remains a serious challenge due to the vast design space and variable physical constraints. This paper meets the challenge of making heterogeneous FTQC design practical by introducing HetArch, a toolbox for designing heterogeneous quantum systems, and using it to explore heterogeneous design scenarios. Using a hierarchical approach, we successively break quantum algorithms into smaller operations (akin to classical application kernels), thus greatly simplifying the design space and resulting tradeoffs. Specializing to superconducting systems, we then design optimized heterogeneous hardware composed of varied superconducting devices, abstracting physical constraints into design rules that enable devices to be assembled into standard cells optimized for specific operations. Finally, we provide a heterogeneous design space exploration framework which reduces the simulation burden by a factor of 10^4 or more and allows us to characterize optimal design points. We use these techniques to design superconducting quantum modules for entanglement distillation, error correction, and code teleportation, reducing error rates by 2.6x, 10.7x, and 3.0x compared to homogeneous systems.

quant-ph↗

arXiv2023

Chemical profiles of the oxides on tantalum in state of the art superconducting circuits

Over the past decades, superconducting qubits have emerged as one of the leading hardware platforms for realizing a quantum processor. Consequently, researchers have made significant effort to understand the loss channels that limit the coherence times of superconducting qubits. A major source of loss has been attributed to two level systems that are present at the material interfaces. We recently showed that replacing the metal in the capacitor of a transmon with tantalum yields record relaxation and coherence times for superconducting qubits, motivating a detailed study of the tantalum surface. In this work, we study the chemical profile of the surface of tantalum films grown on c-plane sapphire using variable energy X-ray photoelectron spectroscopy (VEXPS). We identify the different oxidation states of tantalum that are present in the native oxide resulting from exposure to air, and we measure their distribution through the depth of the film. Furthermore, we show how the volume and depth distribution of these tantalum oxidation states can be altered by various chemical treatments. By correlating these measurements with detailed measurements of quantum devices, we can improve our understanding of the microscopic device losses.

cond-mat.mtrl-sci↗

arXiv2023

Disentangling Losses in Tantalum Superconducting Circuits

Superconducting qubits are a leading system for realizing large scale quantum processors, but overall gate fidelities suffer from coherence times limited by microwave dielectric loss. Recently discovered tantalum-based qubits exhibit record lifetimes exceeding 0.3 ms. Here we perform systematic, detailed measurements of superconducting tantalum resonators in order to disentangle sources of loss that limit state-of-the-art tantalum devices. By studying the dependence of loss on temperature, microwave photon number, and device geometry, we quantify materials-related losses and observe that the losses are dominated by several types of saturable two level systems (TLSs), with evidence that both surface and bulk related TLSs contribute to loss. Moreover, we show that surface TLSs can be altered with chemical processing. With four different surface conditions, we quantitatively extract the linear absorption associated with different surface TLS sources. Finally, we quantify the impact of the chemical processing at single photon powers, the relevant conditions for qubit device performance. In this regime we measure resonators with internal quality factors ranging from 5 to 15 x 10^6, comparable to the best qubits reported. In these devices the surface and bulk TLS contributions to loss are comparable, showing that systematic improvements in materials on both fronts will be necessary to improve qubit coherence further.

quant-ph↗