arXiv subjects

Anton Hohenwarter

Publications and source records attributed to Anton Hohenwarter.

7 recordsLinked to original sources

arXiv2026

Precipitate size evolution in an ultrafine-grained magnesium-manganese alloy

Precipitate size evolution during room temperature high-pressure torsion (HPT) of a Mg-1.35wt.%Mn alloy was studied using scanning transmission electron microscopy (STEM) and Small-/Wide-angle X-ray scattering (SAXS/WAXS). The volume fraction of the nm-scale $α$-Mn particles increased with applied strain, however small angle X-ray scattering (SAXS) indicated that the majority of manganese remained in solution even after 10 HPT rotations, indicating that the reaction progress is still limited by the diffusivity of Mn. Analysis of the precipitate size distribution determined that the mean particle size did not increase over the course of HPT. This, in combination with the precipitate size distribution suggested that precipitate growth was subject to interfacial rather than diffusional control.

cond-mat.mtrl-sci↗

arXiv2025

Dynamic precipitation during high-pressure torsion of a magnesium-manganese alloy

An ultrafine grained magnesium alloy has been produced through room temperature high-pressure torsion (HPT) of solutionised Mg-1.35 wt.%Mn. Dynamic precipitation of nanometer-scale Mn particles occurred during deformation. These particles populated the grain boundaries, acting as pinning sites which allowed the alloy to develop a grain size of 140 nm after 0.5 rotations. Further HPT deformation resulted in a gradual increase in grain size with no increase in precipitate size. Despite the extensive deformation applied, the alloy did not develop a bimodal grain structure and retained a grain size of 230 nm after 10 complete rotations, demonstrating the stability and effectiveness of these pinning particles.

cond-mat.mtrl-sci↗

arXiv2024

Microstructural features and hydrogen diffusion in bcc FeCr alloys: a comparison between the Kelvin probe- and nanohardness based- methods

Hydrogen embrittlement can result in a sudden failure in metallic materials, which is particularly harmful in industrially relevant alloys, such as steels. A more comprehensive understanding of hydrogen interactions with microstructural features is critical for preventing hydrogen-induced damage and promoting a hydrogen-based environment-benign economy. We use the Kelvin probe-based potentiometric hydrogen electrode method and thermal desorption spectroscopy to investigate hydrogen interactions with different hydrogen traps in ferritic FeCr alloys with different chromium contents, dislocation densities, and grain sizes. In addition, we confirm the validity of a novel nanohardness-based diffusion coefficient approach by performing in situ nanoindentation testing. Simultaneous acquisition of the dynamic time-resolved mechanical response of FeCr alloys to hydrogen and the hydrogen diffusivities in these alloys is possible during continuous hydrogen supply. Dislocations, grain boundaries and Cr atoms induce reversible hydrogen trapping sites in these ferritic alloys, leading to the reduction of the hydrogen diffusion coefficients and the increase of the absorbed hydrogen.

cond-mat.mtrl-sci↗

arXiv2024

Stabilization of mechanical strength in a nanocrystalline CoCrNi concentrated alloy by nitrogen alloying

The mechanical performance and microstructures of a CoCrNi medium-entropy alloy (MEA) and NCoCrNi, alloyed with 0.5at% N, after high pressure torsion (HPT) and subsequent annealing treatments in a temperature range of 150-1000 °C were investigated. The introduction of N results in a reduction of grain size by 40% and ~10-15% increased hardness and bending strength after HPT. Both materials showed strain hardening and plasticity after HPT even at these strength levels over 1500 MPa which is induced by the saturated nanocrystalline state. Annealing at intermediate temperatures of 300-500 °C resulted in an additional increase of hardness and strength by ~20-40%, compared to the HPT deformed state. This effect was ~10 % more pronounced in the nitrogen alloyed CoCrNi that also showed better thermal stability. However, the increase in strength after 500 °C annealing was accompanied by a drastic loss of ductility in both materials.

cond-mat.mtrl-sci↗

arXiv2022

Soft Magnetic Properties of Ultra-Strong and Nanocrystalline Pearlitic Wires

The paper describes the capability of magnetic softening of a coarse grained bulk material by a severe deformation technique. Connecting the microstructure with magnetic properties, the coercive field decreases dramatically for grains smaller than the magnetic exchange length. This makes the investigation of soft magnetic properties of severely drawn pearlitic wires very interesting. With the help of the starting two phase microstructure, it is possible to substantially refine the material, which allows the investigation of magnetic properties for nanocrystalline bulk material. Compared to the coarse grained initial, pearlitic state, the coercivities of the highly deformed wires decrease while the saturation magnetization values increase, even beyond the value expectable from the individual constituents. The lowest coercivity in the drawn state is found to be 520 A m for a wire of 24 um thickness and an annealing treatment has a further positive effect on it. The decreasing coercivity is discussed in the framework of two opposing models: grain refinement on the one hand and dissolution of cementite on the other hand. Auxiliary measurements give a clear indication for the latter model, delivering a sufficient description of the observed evolution of magnetic properties.

cond-mat.mtrl-sci↗

arXiv2020

Microstructure and Failure Characteristics of Nanostructured Molybdenum Copper Composites

Liquid-metal infiltrated Cu30Mo70 (weigth percentage) is subjected to severe plastic deformation using high pressure torsion. The initially equiaxed dual phase structure is gradually transformed into a lamellar structure composed of individual Cu and Mo layers. The thickness of the lamellae varies between the micrometer and nanometer ranges depending on the amount of applied strain. Consistent with the refinement of the microstructural features, strength and hardness substantially increase. In addition, an acceptable ductility is found in the intermediate deformation range. An assessment of the damage tolerance of the produced composites is performed by measuring the fracture toughness in different crack propagation directions. The results indicate the development of a pronounced anisotropy with increasing degree of deformation which is an effect of the concurrent alignment of the nanostructured lamellar composite into the shear plane.

cond-mat.mtrl-sci↗

arXiv2016

Exceptional damage-tolerance of a medium-entropy alloy CrCoNi at cryogenic temperatures

High-entropy alloys are an intriguing new class of metallic materials that derive their properties from being multi-element systems that can crystallize as a single phase, despite containing high concentrations of five or more elements with different crystal structures. Here we examine an equiatomic medium-entropy alloy containing only three elements, CrCoNi, as a single-phase face-centered cubic (fcc) solid solution, which displays strength-toughness properties that exceed those of all high-entropy alloys and most multi-phase alloys. At room temperature the alloy shows tensile strengths of almost 1 GPa, failure strains of ~70%, and KJIc fracture-toughness values above 200 MPa.m1/2; at cryogenic temperatures strength, ductility and toughness of the CrCoNi alloy improve to strength levels above 1.3 GPa, failure strains up to 90% and KJIc values of 275 MPa.m1/2. Such properties appear to result from continuous steady strain hardening, which acts to suppress plastic instability, resulting from pronounced dislocation activity and deformation-induced nano-twinning.

cond-mat.mtrl-sci↗