arXiv subjects

Antonio Perillo-Marcone

Publications and source records attributed to Antonio Perillo-Marcone.

11 recordsLinked to original sources

arXiv2026

Manufacturability studies for the FCC-ee positron source target: determination of the minimum bending radius and ovalization in tantalum cooling tube elbows

Beam intercepting devices rely on cooling systems to effectively dissipate the thermal energy generated during the impact of a high-energy beam. Regardless of the device's size, integrating the cooling system is a complex task, particularly when the resulting device is only a few centimetres in size, as is the case with the positron source target for the Future Circular Collider at CERN, where the current design consists of a tungsten core with two embedded tantalum cooling tubes. Due to the reduced dimensions of the chosen tantalum tubes (OD6.35xID4.35 mm), the selected manufacturing method is compression bending. The present study develops and evaluates a numerical model to manufacture the required elbow. The methodology is divided in four steps: i) minium allowable bending radius calculation, ii) material constitutive law validation, iii) prediction of the resulting distortion due to ovalization and iv) experimental validation via (non) destructive methods. The results indicate that a minimum bending radius of 10 mm is suitable for manufacturing the elbow. The distortion caused by ovalization is within +-0.5 mm, resulting in an important deviation respect to the nominal geometry. The numerical model was successfully validated experimentally. The micrographies performed in the cross-section of the tantalum tube before and after plastic bending confirm the integrity of the elbow. Additionally, an empirical expression is proposed to estimate the yield stress of pure tantalum based on Vickers hardness measurements. The proposed numerical model is capable to predict the ovalization along the resulting elbow, offering a viable alternative to define the cooling tube geometry. This study provides a methodology to determine the minimum bending radius for thick walled tubes to be used with compression bending and can be applied for the cooling system design of other high-performance devices

physics.acc-ph↗

arXiv2026

Design and Development of the P-cubed Target Insertion Device (P$^3$-TID)

The P-cubed Target Insertion Device (P$^3$-TID) is a research instrument dedicated to test novel positron source target configurations inside of the proof-of-principle PSI Positron Production (P-cubed or P$^3$) experiment at the Paul Scherrer Institute. The device allows an easy installation, positioning and replacement of different fixed targets. The present article describes its mechanical design at a detailed level.

physics.acc-ph↗

arXiv2025

Conical Targets for Enhanced High-Current Positron Sources

Previous pair-production-driven positron source designs have assumed that the transverse dimension of the target is significantly greater than the secondary beam it generates. This paper explores the use of targets with different transverse profiles with the aim of enhancing positron production. The starting point of this research is the concept of wire targets, proposed by M. James et al. in 1991 for the former SLC positron source. Building on this foundation, this study takes this concept a step further by introducing conical-shaped targets, which can substantially improve the yield by reducing the reabsorption of positrons by the target--an issue that is worsened by the high-field solenoid lenses commonly used for positron capture. Using Geant4 simulations, we propose new conical targets adapted for the parameters of the future collider FCC-ee and its positron source test facility P-cubed (PSI Positron Production experiment) at the Paul Scherrer Institute. We find that conical targets can nearly double the positron production at the target and enhance the baseline positron yield of FCC-ee by around 60%. Additionally, we present the thermo-mechanical studies for the conical targets based on the FCC-ee primary beam power requirements and outline the mechanical implementation for a future proof-of-principle demonstration at the P-cubed facility.

physics.acc-ph↗

arXiv2022

Novel Materials and Concepts for Next-Generation High Power Target Applications

Novel beam-intercepting materials and targetry concepts are essential to improve the performance, reliability and operation lifetimes of next generation multi-megawatt (multi-MW) accelerator target facilities. The beam-intercepting materials and components must sustain an order-of-magnitude increase in particle beam intensities and are beyond the current state-of-the-art. With conventional materials already limiting the scope of experiments, it is crucial to investigate novel target materials, technologies and concepts that will satisfy the requirements and maximize the physics benefits of future energy and intensity frontier experiments. This paper provides an overview of the related targetry R&D required over the next 10 years to support and enable future high-power accelerator target facilities.

physics.acc-ph↗

arXiv2021

High intensity proton beam impact at 440 GeV/c on Mo and Cu coated CfC/graphite and SiC/SiC absorbers for beam intercepting devices

Beam Intercepting Devices (BIDs) are essential protection elements for the operation of the Large Hadron Collider (LHC) complex. The LHC internal beam dump (LHC Target Dump Injection or LHC TDI) is the main protection BID of the LHC injection system; its main function is to protect LHC equipment in the event of a malfunction of the injection kicker magnets during beam transfer from the SPS to the LHC. Several issues with the TDI were encountered during LHC operation, most of them due to outgassing from its core components induced by electron cloud effects, which led to limitations of the injector intensity and hence had an impact on LHC availability. The absorbing cores of the TDIs, and of beam intercepting devices in general, need to deal with high thermo-mechanical loads induced by the high intensity particle beams. In addition, devices such as the TDI - where the absorbing materials are installed close to the beam, are important contributors to the accelerator impedance budget. To reduce impedance, the absorbing materials that make up the core must be typically coated with high electrical conductivity metals. Beam impact testing of the coated absorbers is a crucial element of development work to ensure their correct operation. The behaviour of several metal-coated absorber materials was investigated when exposed to high intensity and high energy proton beams in the HiRadMat facility at CERN. Different coating configurations based on copper and molybdenum, and absorbing materials such as isostatic graphite, Carbon Fibre Composite (CfC) and Silicon Carbide reinforced with Silicon Carbide fibres (SiC-SiC), were tested in the facility to assess the TDI's performance and to extract information for other BIDs using these materials. In addition to beam impact tests and an extensive Post Irradiation Examination (PIE) campaign, extensive numerical simulations were carried out.

physics.acc-ph↗

arXiv2021

Design of the third-generation lead-based neutron spallation target for the neutron time-of-flight facility at CERN

The neutron time-of-flight (n_TOF) facility at the European Laboratory for Particle Physics (CERN) is a pulsed white-spectrum neutron spallation source producing neutrons for two experimental areas: the Experimental Area 1 (EAR1), located 185 m horizontally from the target, and the Experimental Area 2 (EAR2), located 20 m above the target. The target, based on pure lead, is impacted by a high-intensity 20-GeV/c pulsed proton beam. The facility was conceived to study neutron-nucleus interactions for neutron kinetic energies between a few meV to several GeV, with applications of interest for nuclear astrophysics, nuclear technology, and medical research. After the second-generation target reached the end of its lifetime, the facility underwent a major upgrade during CERN's Long Shutdown 2 (LS2, 2019-2021), which included the installation of the new third-generation neutron target. The first and second-generation targets were based on water-cooled massive lead blocks and were designed focusing on EAR1, since EAR2 was built later. The new target is cooled by nitrogen gas to avoid erosion-corrosion and contamination of cooling water with radioactive lead spallation products. Moreover, the new design is optimized also for the vertical flight path and EAR2. This paper presents an overview of the target design focused on both physics and thermo-mechanical performance, and includes a description of the nitrogen cooling circuit and radiation protection studies.

physics.ins-det↗

arXiv2020

Hot Isostatic Pressing (HIP) assisted diffusion bonding between CuCr1Zr and AISI 316L for application to the Super Proton Synchrotron (SPS) internal beam dump at CERN

The new generation internal beam dump of the Super Proton Synchrotron (SPS) at CERN will have to dissipate approximately 270 kW of thermal power, deposited by the primary proton beam. For this purpose, it is essential that the cooling system features a very efficient heat evacuation. Diffusion bonding assisted by Hot Isostatic Pressing (HIP) was identified as a promising method of joining the cooling circuits and the materials of the dump's core in order to maximise the heat transfer efficiency. This paper presents the investigation of HIP assisted diffusion bonding between two CuCr1Zr blanks enclosing SS 316L tubes and the realisation of a real size prototype of one of the dump's cooling plate, as well as the assessments of its cooling performance under the dumps most critical operational scenarios. Energy-dispersive X-ray (EDX) spectroscopy, microstructural analyses, measurements of thermal conductivity and mechanical strength were performed to characterize the HIP diffusion bonded interfaces (CuCr1Zr-CuCr1Zr and CuCr1Zr-SS316L). A test bench allowed to assess the cooling performance of the real size prototype. At the bonded interface, the presence of typical diffusional phenomena was observed. Moreover, measured tensile strength and thermal conductivity were at least equivalent to the lowest ones of the materials assembled and comparable to its bulk properties, meaning that a good bonding quality was achieved. Finally, the real size prototype was successfully tested with an ad-hoc thermal test bench and with the highest operational thermal power expected in the new generation SPS internal beam dump.

physics.ins-det↗

arXiv2020

Design and operation of the air-cooled beam dump for the extraction line of CERN's Proton Synchrotron Booster (PSB)

A new beam dump has been designed, built, installed and operated to withstand the future proton beam extracted from the Proton Synchrotron Booster (PSB) in the framework of the LHC Injector Upgrade (LIU) Project at CERN, consisting of up to 1E14 protons per pulse at 2 GeV, foreseen after the machine upgrades planned for CERN's Long Shutdown 2 (2019-2020). In order to be able to efficiently dissipate the heat deposited by the primary beam, the new dump was designed as a cylindrical block assembly, made out of a copper alloy and cooled by forced airflow. In order to determine the energy density distribution deposited by the beam in the dump, Monte Carlo simulations were performed using the FLUKA code, and thermo-mechanical analyses were carried out by importing the energy density into ANSYS. In addition, Computational Fluid Dynamics (CFD) simulations of the airflow were performed in order to accurately estimate the heat transfer convection coefficient on the surface of the dump. This paper describes the design process, highlights the constraints and challenges of integrating a new dump for increased beam power into the existing facility and provides data on the operation of the dump.

physics.acc-ph↗

arXiv2019

Development of a neutron imaging station at the n\_TOF facility of CERN and applications to beam intercepting devices

A neutron radiography testing station has been developed exploiting the neutron beam of CERN's n\_TOF Experimental Area 2, located at the shortest distance to the neutron producing-target. The characteristics of the n\_TOF neutron beam for the imaging setup are presented in this paper, together with the obtained experimental results. The possible developments of neutron imaging capabilities of the n\_TOF facility in terms of detection-systems and beam-line upgrades are as well outlined.

physics.ins-det↗

arXiv2018

CERN antiproton target: hydrocode analysis of its core material dynamic response under proton beam impact

Antiprotons are produced at CERN by colliding a 26 GeV/c proton beam with a fixed target made of a 3 mm diameter, 55 mm length iridium core. The inherent characteristics of antiproton production involve extremely high energy depositions inside the target when impacted by each primary proton beam, making it one of the most dynamically demanding among high energy solid targets in the world, with a rise temperature above 2000 °C after each pulse impact and successive dynamic pressure waves of the order of GPa's. An optimized redesign of the current target is foreseen for the next 20 years of operation. As a first step in the design procedure, this numerical study delves into the fundamental phenomena present in the target material core under proton pulse impact and subsequent pressure wave propagation by the use of hydrocodes. Three major phenomena have been identified, (i) the dominance of a high frequency radial wave which produces destructive compressive-to-tensile pressure response (ii) The existence of end-of-pulse tensile waves and its relevance on the overall response (iii) A reduction of 40% in tensile pressure could be obtained by the use of a high density tantalum cladding.

physics.ins-det↗

arXiv2018

Scaled Prototype of a Tantalum Target Embedded in Expanded Graphite for Antiproton Production: Design, Manufacturing and Testing under Proton Beam Impacts

This study presents a further step within the ongoing R&D activities for the redesign of the CERN's Antiproton Decelerator Production Target (AD-Target). A first scaled target prototype, constituted of a sliced core made of ten Ta rods -8 mm diameter, 16 mm length- embedded in a compressed expanded graphite (EG) matrix, inserted in a 44 mm diameter Ti-6Al-4V container, has been built and tested under proton beam impacts at the CERN's HiRadMat facility, in the so called HRMT-42 experiment. This prototype has been designed following the lessons learned from previous numerical and experimental works (HRMT-27 experiment) aiming at answering the open questions left in these studies. Velocity data recorded on-line at the target periphery during the HRMT-42 experiment is presented, showing features of its dynamic response to proton beam impacts. Furthermore, x-ray and neutron tomographies of the target prototype after irradiation have been performed. These non-destructive techniques show the extensive plastic deformation of the Ta core, but suggest that the EG matrix can adapt to such deformation, which is a positive result. The neutron tomography successfully revealed the internal state of the tantalum core, showing the appearance of voids of several hundreds of micrometers, in particular in the downstream rods of the core. The possible origin of such voids is discussed while future microstructure analysis after the target opening will try to clarify their nature.

physics.acc-ph↗