arXiv subjects

Antti Tolli

Publications and source records attributed to Antti Tolli.

14 recordsLinked to original sources

arXiv2026

Enhanced Uplink Data Detection for Massive MIMO with 1-Bit ADCs: Analysis and Joint Detection

We present a new analytical framework on the uplink data detection for massive multiple-input multiple-output systems with 1-bit analog-to-digital converters (ADCs). We first characterize the expected values of the soft-estimated symbols (after the linear receiver and prior to the data detection), which are affected by the 1-bit quantization during both the channel estimation and the uplink data transmission. In our analysis, we consider conventional receivers such as maximum ratio combining (MRC), zero forcing, and minimum mean squared error (MMSE), with multiple user equipments (UEs) and correlated Rayleigh fading. Additionally, we design a linear minimum mean dispersion (LMMD) receiver tailored for the data detection with 1-bit ADCs, which exploits the expected values of the soft-estimated symbols previously derived. Then, we propose a joint data detection (JD) strategy that exploits the interdependence among the soft-estimated symbols of the interfering UEs, along with its low-complexity variant. These strategies are compared with the robust maximum likelihood data detection with 1-bit ADCs. Numerical results examining the symbol error rate show that MMSE exhibits a considerable performance gain over MRC, whereas the proposed LMMD receiver significantly outperforms all the conventional receivers. Lastly, the proposed JD and its low-complexity variant provide a significant boost in comparison with the single-UE data detection.

cs.IT↗

arXiv2025

MIMO Detection with Spatial Sigma-Delta ADCs: A Variational Bayesian Approach

The spatial Sigma-Delta ($ΣΔ$) architecture can be leveraged to reduce the quantization noise and enhance the effective resolution of few-bit analog-to-digital converters (ADCs) at certain spatial frequencies of interest. Utilizing the variational Bayesian (VB) inference framework, this paper develops novel data detection algorithms tailored for massive multiple-input multiple-output (MIMO) systems with few-bit $ΣΔ$ ADCs and angular channel models, where uplink signals are confined to a specific angular sector. We start by modeling the corresponding Bayesian networks for the $1^{\mathrm{st}}$- and $2^{\mathrm{nd}}$-order $ΣΔ$ receivers. Next, we propose an iterative algorithm, referred to as Sigma-Delta variational Bayes (SD-VB), for MIMO detection, offering low-complexity updates through closed-form expressions of the variational densities of the latent variables. We also study the impact of mutual coupling on the performance of the proposed SD-VB algorithms when the antenna spacing is reduced. Simulation results show that the proposed $2^{\mathrm{nd}}$-order SD-VB algorithm delivers the best symbol error rate (SER) performance while maintaining the same computational complexity as in unquantized systems, matched-filtering VB with conventional quantization, and linear minimum mean-squared error (LMMSE) methods. Moreover, the $1^{\mathrm{st}}$- and $2^{\mathrm{nd}}$-order SD-VB algorithms achieve their lowest SER at an antenna separation of one-fourth wavelength for a fixed number of antenna elements. The effects of mutual coupling, the steering angle of the $ΣΔ$ architecture, the number of ADC resolution bits, and the number of antennas and users are also extensively analyzed.

eess.SP↗

arXiv2023

Fairness Enhancement of UAV Systems with Hybrid Active-Passive RIS

We consider unmanned aerial vehicle (UAV)-enabled wireless systems where downlink communications between a multi-antenna UAV and multiple users are assisted by a hybrid active-passive reconfigurable intelligent surface (RIS). We aim at a fairness design of two typical UAV-enabled networks, namely the static-UAV network where the UAV is deployed at a fixed location to serve all users at the same time, and the mobile-UAV network which employs the time division multiple access protocol. In both networks, our goal is to maximize the minimum rate among users through jointly optimizing the UAV's location/trajectory, transmit beamformer, and RIS coefficients. The resulting problems are highly nonconvex due to a strong coupling between the involved variables. We develop efficient algorithms based on block coordinate ascend and successive convex approximation to effectively solve these problems in an iterative manner. In particular, in the optimization of the mobile-UAV network, closed-form solutions to the transmit beamformer and RIS passive coefficients are derived. Numerical results show that a hybrid RIS equipped with only 4 active elements and a power budget of 0 dBm offers an improvement of 38%-63% in minimum rate, while that achieved by a passive RIS is only about 15%, with the same total number of elements.

cs.IT↗

arXiv2023

Low-Complexity Multi-Antenna Coded Caching Using Location-Aware Placement Delivery Arrays

A location-aware multi-antenna coded caching scheme is proposed for applications with location-dependent data requests, such as wireless immersive experience, where users are immersed in a three-dimensional virtual world. The wireless connectivity conditions vary as the users move within the application area motivating the use of a non-uniform cache memory allocation process to avoid excessive delivery time for users located in wireless bottleneck areas. To this end, a location-aware placement and delivery array (LAPDA) is designed for cache-aided multiantenna data delivery with a fast converging, iterative linear beamforming process. The underlying weighted max-min transmit precoder design enables the proposed scheme to serve users in poor connectivity areas with smaller amounts of data while simultaneously delivering larger amounts to other users. Our new scheme is suitable for large networks due to its linear transceiver structure and it is not constrained by the number of users, cache size, or the number of antennas at the transmitter, unlike the existing schemes. Despite non-uniform cache placement, the proposed scheme still achieves a significant degree of coded caching gain that is additive to the multiplexing gain and greatly outperforms the conventional symmetric CC schemes in terms of both average and 95-percentile delivery time.

cs.IT↗

arXiv2023

Enhancing Next-Generation Extended Reality Applications with Coded Caching

The next evolutionary step in human-computer interfaces will bring forward immersive digital experiences that submerge users in a 3D world while allowing them to interact with virtual or twin objects. Accordingly, various collaborative extended reality (XR) applications are expected to emerge, imposing stringent performance requirements on the underlying wireless connectivity infrastructure. In this paper, we examine how novel multi-antenna coded caching (CC) techniques can facilitate high-rate low-latency communications and improve users' quality of experience (QoE) in our envisioned multi-user XR scenario. Specifically, we discuss how these techniques make it possible to prioritize the content relevant to wireless bottleneck areas while enabling the cumulative cache memory of the users to be utilized as an additional communication resource. In this regard, we first explore recent advancements in multi-antenna CC that facilitate the efficient use of distributed in-device memory resources. Then, we review how XR application requirements are addressed within the third-generation partnership project (3GPP) framework and how our envisioned XR scenario relates to the foreseen use cases. Finally, we identify new challenges arising from integrating CC techniques into multi-user XR scenarios and propose novel solutions to address them in practice.

cs.HC↗

arXiv2023

D2D Assisted Multi-antenna Coded Caching

A device-to-device (D2D) aided multi-antenna coded caching scheme is proposed to improve the average delivery rate and reduce the downlink (DL) beamforming complexity.} Novel beamforming and resource allocation schemes are proposed where local data exchange among nearby users is exploited. The transmission is split into two phases: local D2D content exchange and DL transmission. In the D2D phase, subsets of users are selected to share content with the adjacent users directly. {In this regard, a low complexity D2D mode selection algorithm is proposed to find the appropriate set of users for the D2D phase with comparable performance to the optimal exhaustive search. {During} the DL phase, the base station multicasts the remaining data requested by all the users. We identify scenarios and conditions where D2D transmission can reduce the delivery time. Furthermore, we demonstrate how} adding the new D2D phase to the DL-only scenario can significantly reduce the beamformer design complexity in the DL phase. The results further highlight that by partly delivering requested data in the D2D phase, the transmission rate can be boosted due to more efficient use of resources during the subsequent DL phase. As a result, the overall content delivery performance is greatly enhanced, especially in the finite signal-to-noise (SNR) regime.

eess.SP↗

arXiv2022

Coded Caching and Spatial Multiplexing Gain Trade-off in Dynamic MISO Networks

The global caching gain of multi-antenna coded caching techniques can be also mostly achieved in dynamic network setups, where the cache contents of users are dictated by a central server, and each user can freely join or leave the network at any moment. In the dynamic setup, users are assigned to a limited set of caching profiles and the non-uniformness in the number of users assigned to each profile is compensated during the delivery phase by either adding phantom users for multicasting or serving a subset of users with unicast transmissions. In this paper, we perform a thorough analysis and provide closed-form representations of the achievable degrees of freedom (DoF) in such hybrid schemes, and assess the inherent trade-off between the global caching and spatial multiplexing gains caused by either adding phantom users or serving parts of the data through unicasting.

cs.IT↗

arXiv2022

Hybrid Active-Passive Reconfigurable Intelligent Surface-Assisted Multi-User MISO Systems

We consider a multi-user multiple-input single-output (MISO) communications system which is assisted by a hybrid active-passive reconfigurable intelligent surface (RIS). Unlike conventional passive RISs, hybrid RIS is equipped with a few active elements with the ability to reflect and amplify incident signals to significantly improve the system performance. Towards a fairness-oriented design, we maximize the minimum rate among all users through jointly optimizing the transmit beamforming vectors and RIS reflecting/amplifying coefficients. Combining tools from block coordinate ascent and successive convex approximation, the challenging nonconvex problem is efficiently solved by a low-complexity iterative algorithm. The numerical results show that a hybrid RIS with 4 active elements out of a total of 50 elements with a power budget of -1 dBm offers an improvement of up to 80% to the considered system, while that achieved by a fully passive RIS is only 27%.

cs.IT↗

arXiv2021

Low-Subpacketization Multi-Antenna Coded Caching for Dynamic Networks

Multi-antenna coded caching combines a global caching gain, proportional to the total cache size in the network, with an additional spatial multiplexing gain that stems from multiple transmitting antennas. However, classic centralized coded caching schemes are not suitable for dynamic networks as they require prior knowledge of the number of users to indicate what data should be cached at each user during the placement phase. On the other hand, fully decentralized schemes provide comparable gains to their centralized counterparts only when the number of users is very large. In this paper, we propose a novel multi-antenna coded caching scheme for dynamic networks, where instead of defining individual cache contents, we associate users with a limited set of predefined caching profiles. Then, during the delivery phase, we aim at achieving a combined caching and spatial multiplexing gain, comparable to a large extent with the ideal case of fully centralized schemes. The resulting scheme imposes small subpacketization and beamforming overheads, is robust under dynamic network conditions, and incurs small finite-SNR performance loss compared with centralized schemes.

cs.IT↗

arXiv2021

Low-complexity Multicast Beamforming for Multi-stream Multi-group Communications

In this paper, assuming multi-antenna transmitter and receivers, we consider multicast beamformer design for the weighted max-min-fairness (WMMF) problem in a multi-stream multi-group communication setup. Unlike the single-stream scenario, the WMMF objective in this setup is not equivalent to maximizing the minimum weighted SINR due to the summation over the rates of multiple streams. Therefore, the non-convex problem at hand is first approximated with a convex one and then solved using Karush-Kuhn-Tucker (KKT) conditions. Then, a practically appealing closed-form solution is derived, as a function of dual variables, for both transmit and receive beamformers. Finally, we use an iterative solution based on the sub-gradient method to solve for the mutually coupled and interdependent dual variables. The proposed solution does not rely on generic solvers and does not require any bisection loop for finding the achievable rate of various streams. As a result, it significantly outperforms the state-of-art in terms of computational cost and convergence speed.

cs.IT↗

arXiv2021

Scoring the Terabit/s Goal:Broadband Connectivity in 6G

This paper explores the road to vastly improving the broadband connectivity in future 6G wireless systems. Different categories of use cases are considered, with peak data rates up to 1 Tbps. Several categories of enablers at the infrastructure, spectrum, and protocol/algorithmic levels are required to realize the intended broadband connectivity goals in 6G. At the infrastructure level, we consider ultra-massive MIMO technology (possibly implemented using holographic radio), intelligent reflecting surfaces, user-centric cell-free networking, integrated access and backhaul, and integrated space and terrestrial networks. At the spectrum level, the network must seamlessly utilize sub-6 GHz bands for coverage and spatial multiplexing of many devices, while higher bands will be mainly used for pushing the peak rates of point-to-point links. Finally, at the protocol/algorithmic level, the enablers include improved coding, modulation, and waveforms to achieve lower latency, higher reliability, and reduced complexity.

eess.SP↗

arXiv2020

Hybrid Beamforming for mm-Wave Massive MIMO Systems with Partially Connected RF Architecture

To satisfy the capacity requirements of future mobile systems, under-utilized millimeter wave frequencies can be efficiently exploited by employing massive MIMO technology with highly directive beamforming. Hybrid analog-digital beamforming has been recognised as a promising approach for large-scale MIMO implementations with a reduced number of costly and power-hungry RF chains. In comparison to fully connected architecture, hybrid beamforming (HBF) with partially connected RF architecture is particularly appealing for the practical implementation due to less complex RF power division and combining networks. In this paper, we first formulate single- and multi-user rate maximization problems as weighted minimum mean square error (WMMSE) and derive solutions for hybrid beamformers using alternating optimization. The algorithms are designed for the full-array- and sub-array-based processing strategies of partially connected HBF architecture. In addition to the rate maximizing WMMSE solutions, we propose lower complexity sub-array-based zero-forcing algorithms. The performance of the proposed algorithms is evaluated in two different channel models, i.e., a simple geometric model and a realistic statistical millimeter wave model known as NYUSIM. The performance results of the WMMSE HBF algorithms are meant to reveal the potential of partially connected HBF and serve as upper bounds for lower complexity methods. Numerical results imply that properly designed partially connected HBF has the potential to provide an good compromise between hardware complexity and system performance in comparison to fully digital beamforming.

eess.SP↗

arXiv2020

White Paper on Broadband Connectivity in 6G

This white paper explores the road to implementing broadband connectivity in future 6G wireless systems. Different categories of use cases are considered, from extreme capacity with peak data rates up to 1 Tbps, to raising the typical data rates by orders-of-magnitude, to support broadband connectivity at railway speeds up to 1000 km/h. To achieve these goals, not only the terrestrial networks will be evolved but they will also be integrated with satellite networks, all facilitating autonomous systems and various interconnected structures. We believe that several categories of enablers at the infrastructure, spectrum, and protocol/ algorithmic levels are required to realize the intended broadband connectivity goals in 6G. At the infrastructure level, we consider ultra-massive MIMO technology (possibly implemented using holographic radio), intelligent reflecting surfaces, user-centric and scalable cell-free networking, integrated access and backhaul, and integrated space and terrestrial networks. At the spectrum level, the network must seamlessly utilize sub-6 GHz bands for coverage and spatial multiplexing of many devices, while higher bands will be used for pushing the peak rates of point-to-point links. The latter path will lead to THz communications complemented by visible light communications in specific scenarios. At the protocol/algorithmic level, the enablers include improved coding, modulation, and waveforms to achieve lower latencies, higher reliability, and reduced complexity. Different options will be needed to optimally support different use cases. The resource efficiency can be further improved by using various combinations of full-duplex radios, interference management based on rate-splitting, machine-learning-based optimization, coded caching, and broadcasting.

eess.SP↗

arXiv2016

DoF Analysis in a Two-Layered Heterogeneous Wireless Interference Network

Degrees of freedom (DoF) is studied in the downlink of a heterogenous wireless network modeled as a two-layered interference network. The first layer of the interference network is the backhaul layer between macro base stations (MB) and small cell base stations (SB), which is modeled as a Wyner type linear network. The second layer is the transmission layer between SBs and mobile terminals (MTs), which is modeled as a linear Wyner $L_T$ network, i.e., each MT is connected to $L_T+1$ SBs. The SBs are assumed to be half-duplex, thus restricting the per user degrees of freedom (puDoF) in the system to $1/2$. The puDoF can be further restricted by the number of antennas at the MB. For $L_T \in \{1,2\}$, the optimal puDoF can be achieved by using simple interference avoidance schemes. The increase in the connectivity of transmission layer beyond $L_T=2$ limits the achievable puDoF using only zero-forcing schemes to less than 1/2, even in the presence of large number of antennas at each MB but the optimal puDoF can be achieved by making each message available at multiple SBs. This is done by sending an appropriate linear combination to the SB to zero-force interference at the intended user. The maximum per user DoF of 1/2 can be achieved in the linear network with sufficient number of antennas using only interference avoidance schemes. These results are also extended to a more realistic hexagonal cellular model as well.

cs.IT↗