arXiv subjects

Armand Béché

Publications and source records attributed to Armand Béché.

At least 19 recordsLinked to original sources

arXiv2023

Quantum Wavefront Shaping with a 48-element Programmable Phase Plate for Electrons

We present a 48-element programmable phase plate for coherent electron waves produced by a combination of photolithography and focused ion beam. This brings the highly successful concept of wavefront shaping from light optics into the realm of electron optics and provides an important new degree of freedom to prepare electron quantum states. The phase plate chip is mounted on an aperture rod placed in the C2 plane of a transmission electron microscope operating in the 100-300 kV range. The phase plate's behavior is characterized by a Gerchberg-Saxton algorithm, showing a phase sensitivity of 0.075rad/mV at 300kV, with a phase resolution of approximately $3\cdot10^{-3}π$. In addition, we provide a brief overview of possible use cases and support it with both simulated and experimental results.

physics.ins-det↗

arXiv2022

Absence of a pressure gap and atomistic mechanism of the oxidation of pure Co nanoparticles

We present a detailed atomistic picture of the oxidation mechanism of Co nanoparticles and its impact on magnetism by experimentally following the evolution of the structure, chemical composition, and magnetism of individual, gas-phase grown Co nanoparticles during controlled oxidation. The early stage oxidation occurs in a twostep process characterized by (i) the initial formation of small CoO crystallites randomly distributed across the nanoparticle surface, until their coalescence leads to structural completion of the oxide shell and passivation of the metallic core; (ii) progressive conversion of the CoO shell to Co3O4, accompanied by void formation due to the nanoscale Kirkendall effect. The Co nanoparticles remain highly reactive toward oxygen during phase (i), demonstrating the absence of a pressure gap whereby a low reactivity at low pressures is postulated. Our results provide an important benchmark for an improved understanding of the magnetism of oxidized cobalt nanoparticles, with potential implications on their performance in catalytic reactions.

cond-mat.mtrl-sci↗

arXiv2022

Can a Programmable Phase Plate Serve as an Aberration Corrector in the Transmission Electron Microscope (TEM)?

Current progress in programmable electrostatic phase plates raises questions about their usefulness for specific applications. Here, we explore different designs for such phase plates with the specific goal of correcting spherical aberration in the Transmission Electron Microscope (TEM). We numerically investigate whether a phase plate could provide down to 1 $Å$ngström spatial resolution on a conventional uncorrected TEM. Different design aspects (fill-factor, pixel pattern, symmetry) were evaluated to understand their effect on the electron probe size and current density. Some proposed designs show a probe size ($d_{50}$) down to 0.66$Å$, proving that it should be possible to correct spherical aberration well past the 1Å~ limit using a programmable phase plate consisting of an array of electrostatic phase shifting elements.

physics.app-ph↗

arXiv2021

Event driven 4D STEM acquisition with a Timepix3 detector: microsecond dwell time and faster scans for high precision and low dose applications

Four dimensional scanning transmission electron microscopy (4D STEM) records the scattering of electrons in a material in great detail. The benefits offered by 4D STEM are substantial, with the wealth of data it provides facilitating for instance high precision, high electron dose efficiency phase imaging via center of mass or ptychography based analysis. However the requirement for a 2D image of the scattering to be recorded at each probe position has long placed a severe bottleneck on the speed at which 4D STEM can be performed. Recent advances in camera technology have greatly reduced this bottleneck, with the detection efficiency of direct electron detectors being especially well suited to the technique. However even the fastest frame driven pixelated detectors still significantly limit the scan speed which can be used in 4D STEM, making the resulting data susceptible to drift and hampering its use for low dose beam sensitive applications. Here we report the development of the use of an event driven Timepix3 direct electron camera that allows us to overcome this bottleneck and achieve 4D STEM dwell times down to 100~ns; orders of magnitude faster than what has been possible with frame based readout. We characterise the detector for different acceleration voltages and show that the method is especially well suited for low dose imaging and promises rich datasets without compromising dwell time when compared to conventional STEM imaging.

physics.ins-det↗

arXiv2021

Reducing electron beam damage through alternative STEM scanning strategies. Part I -- Experimental findings

The highly energetic electrons in a transmission electron microscope (TEM) can alter or even completely destroy the structure of samples before sufficient information can be obtained. This is especially problematic in the case of zeolites, organic and biological materials. As this effect depends on both the electron beam and the sample and can involve multiple damage pathways, its study remained difficult and is plagued with irreproducibity issues, circumstantial evidence, rumours, and a general lack of solid data. Here we take on the experimental challenge to investigate the role of the STEM scan pattern on the damage behaviour of a commercially available zeolite sample with the clear aim to make our observations as reproducible as possible. We make use of a freely programmable scan engine that gives full control over the tempospatial distribution of the electron probe on the sample and we use its flexibility to obtain mutliple repeated experiments under identical conditions comparing the difference in beam damage between a conventional raster scan pattern and a newly proposed interleaved scan pattern that provides exactly the same dose and dose rate and visits exactly the same scan points. We observe a significant difference in beam damage for both patterns with up to 11 % reduction in damage (measured from mass loss). These observations demonstrate without doubt that electron dose, dose rate and acceleration voltage are not the only parameters affecting beam damage in (S)TEM experiments and invite the community to rethink beam damage as an unavoidable consequence of applied electron dose.

cond-mat.mtrl-sci↗

arXiv2021

HAADF-STEM block-scanning strategy for local measurement of strain at the nanoscale

Lattice strain measurement of nanoscale semiconductor devices is crucial for the semiconductor industry as strain substantially improves the electrical performance of transistors. High resolution scanning transmission electron microscopy (HR-STEM) imaging is an excellent tool that provides spatial resolution at the atomic scale and strain information by applying Geometric Phase Analysis or image fitting procedures. However, HR-STEM images regularly suffer from scanning distortions and sample drift during image acquisition. In this paper, we propose a new scanning strategy that drastically reduces artefacts due to drift and scanning distortion, along with extending the field of view. The method allows flexible tuning of the spatial resolution and decouples the choice of field of view from the need for local atomic resolution. It consists of the acquisition of a series of independent small subimages containing an atomic resolution image of the local lattice. All subimages are then analysed individually for strain by fitting a nonlinear model to the lattice images. The obtained experimental strain maps are quantitatively benchmarked against the Bessel diffraction technique. We demonstrate that the proposed scanning strategy approaches the performance of the diffraction technique while having the advantage that it does not require specialized diffraction cameras.

physics.app-ph↗

arXiv2020

Single femtosecond laser pulse excitation of individual cobalt nanoparticles

Laser-induced manipulation of magnetism at the nanoscale is a rapidly growing research topic with potential for applications in spintronics. In this work, we address the role of the scattering cross section, thermal effects, and laser fluence on the magnetic, structural, and chemical stability of individual magnetic nanoparticles excited by single femtosecond laser pulses. We find that the energy transfer from the fs laser pulse to the nanoparticles is limited by the Rayleigh scattering cross section, which in combination with the light absorption of the supporting substrate and protective layers determines the increase in the nanoparticle temperature. We investigate individual Co nanoparticles (8 to 20 nm in size) as a prototypical model system, using x-ray photoemission electron microscopy and scanning electron microscopy upon excitation with single femtosecond laser pulses of varying intensity and polarization. In agreement with calculations, we find no deterministic or stochastic reversal of the magnetization in the nanoparticles up to intensities where ultrafast demagnetization or all-optical switching is typically reported in thin films. Instead, at higher fluences, the laser pulse excitation leads to photo-chemical reactions of the nanoparticles with the protective layer, which results in an irreversible change in the magnetic properties. Based on our findings, we discuss the conditions required for achieving laser-induced switching in isolated nanomagnets.

cond-mat.mes-hall↗

arXiv2020

Fast versus conventional HAADF-STEM tomography: advantages and challenges

Electron tomography is a widely used experimental technique for analyzing nanometer-scale structures of a large variety of materials in three dimensions. Unfortunately, the acquisition of conventional electron tomography tilt series can easily take up one hour or more, depending on the complexity of the experiment. Using electron tomography, it is therefore far from straightforward to obtain statistically meaningful 3D data, to investigate samples that do not withstand long acquisition, or to perform in situ 3D characterization using this technique. Various acquisition strategies have been proposed to accelerate the tomographic acquisition, and reduce the required electron dose. These methods include tilting the holder continuously while acquiring a projection movie and a hybrid, incremental, methodology which combines the benefits of the conventional and continuous technique. In this paper, the different acquisition strategies will be experimentally compared in terms of speed, resolution and electron dose, based on experimental tilt series acquired for various metallic nanoparticles.

cond-mat.mtrl-sci↗

arXiv2020

Evaluation of different rectangular scan strategies for STEM imaging

STEM imaging is typically performed by raster scanning a focused electron probe over a sample. Here we investigate and compare three different scan patterns, making use of a programmable scan engine that allows to arbitrarily set the sequence of probe positions that are consecutively visited on the sample. We compare the typical raster scan with a so-called 'snake' pattern where the scan direction is reversed after each row and a novel Hilbert scan pattern that changes scan direction rapidly and provides an homogeneous treatment of both scan directions. We experimentally evaluate the imaging performance on a single crystal test sample by varying dwell time and evaluating behaviour with respect to sample drift. We demonstrate the ability of the Hilbert scan pattern to more faithfully represent the high frequency content of the image in the presence of sample drift. It is also shown that Hilbert scanning provides reduced bias when measuring lattice parameters from the obtained scanned images while maintaining similar precision in both scan directions which is especially important when e.g. performing strain analysis. Compared to raster scanning with flyback correction, both snake and Hilbert scanning benefit from dose reduction as only small probe movement steps occur.

physics.app-ph↗

arXiv2019

Strain measurement in semiconductor FinFET devices using a novel moiré demodulation technique

Moiré fringes are used throughout a wide variety of applications in physics and engineering to bring out small variations in an underlying lattice by comparing with another reference lattice. This method was recently demonstrated in Scanning Transmission Electron Microscopy imaging to provide local strain measurement in crystals by comparing the crystal lattice with the scanning raster that then serves as the reference. The images obtained in this way contain a beating fringe pattern with a local period that represents the deviation of the lattice from the reference. In order to obtain the actual strain value, a region containing a full period of the fringe is required, which results in a compromise between strain sensitivity and spatial resolution. In this paper we propose an advanced setup making use of an optimised scanning pattern and a novel phase stepping demodulation scheme. We demonstrate the novel method on a series of 16 nm Si-Ge semiconductor FinFET devices in which strain plays a crucial role in modulating the charge carrier mobility. The obtained results are compared with both Nano-beam diffraction and the recently proposed Bessel beam diffraction technique. The setup provides a much improved spatial resolution over conventional moiré imaging in STEM while at the same time being fast and requiring no specialised diffraction camera as opposed to the diffraction techniques we compare to.

physics.app-ph↗

arXiv2019

Electron Bessel beam diffraction for precise and accurate nanoscale strain mapping

Strain has a strong effect on the properties of materials and the performance of electronic devices. Their ever shrinking size translates into a constant demand for accurate and precise measurement methods with very high spatial resolution. In this regard, transmission electron microscopes are key instruments thanks to their ability to map strain with sub-nanometer resolution. Here we present a novel method to measure strain at the nanometer scale based on the diffraction of electron Bessel beams. We demonstrate that our method offers a strain sensitivity better than $2.5 \cdot 10^{-4}$ and an accuracy of $1.5 \cdot 10^{-3}$, competing with, or outperforming, the best existing methods with a simple and easy to use experimental setup.

cond-mat.mtrl-sci↗

arXiv2019

Spectroscopic coincidence experiments in transmission electron microscopy

We demonstrate the feasibility of coincidence measurements in a conventional transmission electron microscope, revealing the temporal correlation between electron energy loss spectroscopy (EELS) and energy dispersive X-ray (EDX) spectroscopy events. We make use of a delay line detector with picosecond time resolution attached to a modified EELS spectrometer. We demonstrate that coincidence between both events, related to the excitation and de-excitation of atoms in a crystal, provides added information not present in the individual EELS or EDX spectra. In particular, the method provides EELS with a significantly suppressed or even removed background, overcoming the many difficulties with conventional parametric background fitting as it uses no assumptions on the shape of the background, requires no user input and does not suffer from counting noise originating from the background signal. This is highly attractive, especially when low concentrations of elements need to be detected in a matrix of other elements.

physics.ins-det↗

arXiv2019

Various Compressed Sensing Set-Ups Evaluated Against Shannon Sampling Under Constraint of Constant Illumination

Under the constraint of constant illumination, an information criterion is formulated for the Fisher information that compressed sensing measurements in optical and transmission electron microscopy contain about the underlying parameters. Since this approach requires prior knowledge of the signal's support in the sparse basis, we develop a heuristic quantity, the detective quantum efficiency (DQE), that tracks this information criterion well without this knowledge. It is shown that for the investigated choice of sensing matrices, and in the absence of read-out noise, i.e. with only Poisson noise present, compressed sensing does not raise the amount of Fisher information in the recordings above that of Shannon sampling. Furthermore, enabled by the DQE's analytical tractability, the experimental designs are optimized by finding out the optimal fraction of on-pixels as a function of dose and read-out noise. Finally, we introduce a regularization and demonstrate, through simulations and experiment, that it yields reconstructions attaining minimum mean squared error at experimental settings predicted by the DQE as optimal.

physics.ins-det↗

arXiv2017

Demonstration of a 2x2 programmable phase plate for electrons

First results on the experimental realisation of a 2x2 programmable phase plate for electrons are presented. The design consists of an array of electrostatic einzel lenses that influence the phase of electron waves passing through 4 separately controllable aperture holes. This functionality is demonstrated in a conventional transmission electron microscope operating at 300~kV and results are in very close agreement with theoretical predictions. The dynamic creation of a set of electron probes with different phase symmetry is demonstrated, thereby bringing adaptive optics in TEM one step closer to reality. The limitations of the current design and how to overcome these in the future are discussed. Simulations show how further evolved versions of the current proof of concept might open new and exciting application prospects for beam shaping and aberration correction.

physics.app-ph↗

arXiv2017

Probing the symmetry of the potential of localized surface plasmon resonances with phase-shaped electron beams

Plasmonics, the science and technology of the interaction of light with metallic objects, is fundamentally changing the way we can detect, generate and manipulate light. Although the field is progressing swiftly, thanks to the availability of nanoscale manufacturing and analysis methods, fundamental properties such as the plasmonic excitations' symmetries cannot be accessed directly, leading to a partial, sometimes incorrect, understanding of their properties. Here we overcome this limitation by deliberately shaping the wave function of an electron beam to match a plasmonic excitations' symmetry in a modified transmission electron microscope. We show experimentally and theoretically that this offers selective detection of specific plasmon modes within metallic nanoparticles, while excluding modes with other symmetries. This method resembles the widespread use of polarized light for the selective excitation of plasmon modes with the advantage of locally probing the response of individual plasmonic objects and a far wider range of symmetry selection criteria.

physics.optics↗

arXiv2017

Direct observation of enhanced magnetism in individual size- and shape-selected 3d transition metal nanoparticles

Magnetic nanoparticles are important building blocks for future technologies ranging from nano-medicine to spintronics. Many related applications require nanoparticles with tailored magnetic properties. However, despite significant efforts undertaken towards this goal, a broad and poorly-understood dispersion of magnetic properties is reported, even within mono-disperse samples of the canonical ferromagnetic 3d transition metals. We address this issue by investigating the magnetism of a large number of size- and shape-selected, individual nanoparticles of Fe, Co, and Ni using a unique set of complementary characterization techniques. At room temperature only superparamagnetic behavior is observed in our experiments for all Ni nanoparticles within the investigated sizes, which range from 8 to 20 nm. However, Fe and Co nanoparticles can exist in two distinct magnetic states at any size in this range: (i) a superparamagnetic state as expected from the bulk and surface anisotropies known for the respective materials and as observed for Ni; and (ii) a state with unexpected stable magnetization at room temperature. This striking state is assigned to significant modifications of the magnetic properties arising from metastable lattice defects in the core of the nanoparticles as concluded by calculations and atomic structural characterization. Also related with the structural defects, we find that the magnetic state of Fe and Co nanoparticles can be tuned by thermal treatment enabling one to tailor their magnetic properties for applications. This work demonstrates the importance of complementary single particle investigations for a better understanding of nanoparticle magnetism and for full exploration of their potential for applications.

cond-mat.mes-hall↗

arXiv2015

Development of a fast electromagnetic shutter for compressive sensing imaging in scanning transmission electron microscopy

The concept of compressive sensing was recently proposed to significantly reduce the electron dose in scanning transmission electron microscopy (STEM) while still maintaining the main features in the image. Here, an experimental setup based on an electromagnetic shutter placed in the condenser plane of a STEM is proposed. The shutter blanks the beam following a random pattern while the scanning coils are moving the beam in the usual scan pattern. Experimental images at both medium scale and high resolution are acquired and then reconstructed based on a discrete cosine algorithm. The obtained results confirm the predicted usefulness of compressive sensing in experimental STEM even though some remaining artifacts need to be resolved.

physics.ins-det↗

arXiv2015

Prospects for versatile phase manipulation in the TEM: beyond aberration correction

In this paper we explore the desirability of a transmission electron microscope in which the phase of the electron wave can be freely controlled. We discuss different existing methods to manipulate the phase of the electron wave and their limitations. We show how with the help of current techniques the electron wave can already be crafted into specific classes of waves each having their own peculiar properties. Assuming a versatile phase modulation device is feasible, we explore possible benefits and methods that could come into existence borrowing from light optics where so-called spatial light modulators provide programmable phase plates for quite some time now. We demonstrate that a fully controllable phase plate building on Harald Rose's legacy in aberration correction and electron optics in general would open an exciting field of research and applications.

cond-mat.mtrl-sci↗