arXiv subjects

B. L. Goldblum

Publications and source records attributed to B. L. Goldblum.

17 recordsLinked to original sources

arXiv2024

Proton discrimination in CLYC for fast neutron spectroscopy

The Cs$_2$LiYCl$_6$:Ce (CLYC) elpasolite scintillator is known for its response to fast and thermal neutrons along with good $γ$-ray energy resolution. While the $^{35}$Cl($n,p$) reaction has been identified as a potential means for CLYC-based fast neutron spectroscopy in the absence of time-of-flight (TOF), previous efforts to functionalize CLYC as a fast neutron spectrometer have been thwarted by the inability to isolate proton interactions from $^{6}$Li($n,α$) and $^{35}$Cl($n,α$) signals. This work introduces a new approach to particle discrimination in CLYC for fission spectrum neutrons using a multi-gate charge integration algorithm that provides excellent separation between protons and heavier charged particles. Neutron TOF data were collected using a $^{252}$Cf source, an array of EJ-309 organic liquid scintillators, and a $^6$Li-enriched CLYC scintillator outfitted with fast electronics. Modal waveforms were constructed corresponding to the different reaction channels, revealing significant differences in the pulse characteristics of protons and heavier charged particles at ultrafast, fast, and intermediate time scales. These findings informed the design of a pulse shape discrimination algorithm, which was validated using the TOF data. This study also proposes an iterative subtraction method to mitigate contributions from confounding reaction channels in proton and heavier charged particle pulse height spectra, opening the door for CLYC-based fast neutron and $γ$-ray spectroscopy while preserving sensitivity to thermal neutron capture signals.

physics.ins-det↗

arXiv2024

Characterization of a SiPM-based monolithic neutron scatter camera using dark counts

We report on the design and characterization of a prototype monolithic neutron scatter camera that is intended to significantly improve upon the geometrical shortcomings of conventional neutron cameras. The detector consists of a 50 mm $\times$ 56 mm $\times$ 60 mm monolithic block of EJ-204 plastic scintillator instrumented on two faces with arrays of 64 Hamamatsu S13360-6075PE silicon photomultipliers (SiPMs). The electronic crosstalk is limited to < 5% between adjacent channels and < 0.1% between all other channel pairs. SiPMs introduce a significantly elevated dark count rate over PMTs, as well as correlated noise from after-pulsing and optical crosstalk. In this article, we characterize the dark count rate and optical crosstalk and present a modified event reconstruction likelihood function that accounts for them. We find that the average dark count rate per SiPM is 4.3 MHz with a standard deviation of 1.5 MHz among devices. The analysis method we employ to measure internal optical crosstalk also naturally yields the mean and width of the single-electron pulse height. We calculate separate contributions to the width of the single-electron pulse-height from electronic noise and avalanche fluctuations. We demonstrate a timing resolution for a single-photon pulse to be 128 ($\pm$4) ps. Finally, coincidence analysis is employed to measure external (pixel-to-pixel) optical crosstalk. We present a map of the average external crosstalk probability between 2-by-4 groups of SiPMs, as well as the in-situ timing characteristics extracted from the coincidence analysis. Further work is needed to characterize the performance of the camera at reconstructing single- and double-site interactions, as well as image reconstruction.

physics.ins-det↗

arXiv2023

Global Characterization of a Laser-Generated Neutron Source

Laser-driven neutron sources are routinely produced by the interaction of laser-accelerated protons with a converter. They present complementary characteristics to those of conventional accelerator-based neutron sources (e.g. short pulse durations, enabling novel applications like radiography). We present here results from an experiment aimed at performing a global characterization of the neutrons produced using the Titan laser at the Jupiter Laser Facility (Livermore, USA), where protons were accelerated from 23 $μm$ thick plastic targets and directed onto a LiF converter to produce neutrons. For this purpose, several diagnostics were used to measure these neutron emissions, such as CR-39, activation foils, Time-of-Flight detectors and direct measurement of $^{7}$Be residual activity in the LiF converters. The use of these different, independently operating diagnostics enables comparison of the various measurements performed to provide a robust characterization. These measurements led to a neutron yield of $2.10^{9}$ neutrons per shot with a modest angular dependence, close to that simulated.

physics.acc-ph↗

arXiv2023

Absolute light yield of the EJ-204 plastic scintillator

The absolute light yield of a scintillator, defined as the number of scintillation photons produced per unit energy deposited, is a useful quantity for scintillator development, research, and applications. Yet, literature data on the absolute light yield of organic scintillators are limited. The goal of this work is to assess the suitability of the EJ-204 plastic scintillator from Eljen Technology to serve as a reference standard for measurements of the absolute light yield of organic scintillators. Four EJ-204 samples were examined: two manufactured approximately four months prior and stored in high-purity nitrogen, and two aged approximately eleven years and stored in ambient air. The scintillator response was measured using a large-area avalanche photodiode calibrated using low energy $γ$-ray and X-ray sources. The product of the quantum efficiency of the photodetector and light collection efficiency of the housing was characterized using an experimentally-benchmarked optical photon simulation. The average absolute light yield of the fresh samples, 9100 $\pm$ 400 photons per MeV, is lower than the manufacturer-reported value of 10400 photons per MeV. Moreover, the aged samples demonstrated significantly lower light yields, deviating from the manufacturer specification by as much as 26\%. These results are consistent with recent work showcasing environmental aging in plastic scintillators and suggest that experimenters should use caution when deploying plastic scintillators in photon counting applications.

physics.ins-det↗

arXiv2022

Measurement of proton light yield of water-based liquid scintillator

The proton light yield of liquid scintillators is an important property in the context of their use in large-scale neutrino experiments, with direct implications for neutrino-proton scattering measurements and the discrimination of fast neutrons from inverse beta-decay coincidence signals. This work presents the first measurement of the proton light yield of a water-based liquid scintillator (WbLS) formulated from 5% linear alkyl benzene (LAB), at energies below 20 MeV, as well as a measurement of the proton light yield of a pure LAB + 2 g/L 2,5-diphenyloxazole (PPO) mixture (LABPPO). The measurements were performed using a double time-of-flight method and a pulsed neutron beam from the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory. The proton light yields were measured relative to that of a 477 keV electron. The relative proton light yield of WbLS was approximately 3.8% lower than that of LABPPO, itself exhibiting a relative proton light yield $15-20\%$ higher than previous measurements of an analogous anoxic sample. The observed quenching is not compatible with the Birks model for either material, but is well described with the addition of Chou's bimolecular quenching term.

physics.ins-det↗

arXiv2021

Simultaneous measurement of organic scintillator response to carbon and proton recoils

Background: Organic scintillators are widely used for neutron detection in both basic nuclear physics and applications. While the proton light yield of organic scintillators has been extensively studied, measurements of the light yield from neutron interactions with carbon nuclei are scarce. Purpose: Demonstrate a new approach for the simultaneous measurement of the proton and carbon light yield of organic scintillators. Provide new carbon light yield data for the EJ-309 liquid and EJ-204 plastic organic scintillators. Method: A 33~MeV $^{2}$H$^{+}$ beam from the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory was impinged upon a 3-mm-thick Be target to produce a high-flux, broad-spectrum neutron beam. The double time-of-flight technique was extended to simultaneously measure the proton and carbon light yield of the organic scintillators, wherein the light output associated with the recoil particle was determined using $np$ and $n$C elastic scattering kinematics. Results: The proton and carbon light yield relations of the EJ-309 liquid and EJ-204 plastic organic scintillators were measured over a recoil energy range of approximately 0.3 to 1~MeV and 2 to 5~MeV, respectively for EJ-309, and 0.2 to 0.5~MeV and 1 to 4~MeV, respectively for EJ-204. Conclusions: These data provide new insight into the ionization quenching effect in organic scintillators and key input for simulation of the response of organic scintillators for both basic science and a broad range of applications.

physics.ins-det↗

arXiv2021

Proton light yield of fast plastic scintillators for neutron imaging

Plastic organic scintillators have been tailored in composition to achieve ultra-fast temporal response, thereby enabling the design and development of fast neutron detection systems with high timing resolution. Eljen Technology's plastic organic scintillators -- EJ-230, EJ-232, and EJ-232Q -- are prospective candidates for use in emerging neutron imaging systems, where fast timing is paramount. To support the neutron response characterization of these materials, the relative proton light yields of EJ-230, EJ-232, and EJ-232Q were measured at the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory. Using a broad-spectrum neutron source and a double time-of-flight technique, the proton light yield relations were obtained over a proton recoil energy range of approximately 300 keV to 4 MeV. The EJ-230, EJ-232, and EJ-232Q scintillators exhibited similar proton light yield relations to each other as well as to other plastic scintillators with the same polymer base material. A comparison of the relative proton light yield of different sized cylindrical EJ-232 and EJ-232Q scintillators also revealed consistent results. This work provides key input data for the realistic computational modeling of neutron detection technologies employing these materials, thereby supporting new capabilities in near-field radionuclide detection for national security applications.

physics.ins-det↗

arXiv2020

Comparative scintillation performance of EJ-309, EJ-276, and a novel organic glass

An organic glass scintillator developed by Sandia National Laboratories was characterized in terms of its light output and pulse shape discrimination (PSD) properties and compared to commercial liquid (EJ-309) and plastic (EJ-276) organic scintillators. The electron light output was determined through relative comparison of the $^{137}$Cs Compton edge location. The proton light yield was measured using a double time-of-flight technique at the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory. Using a tunable broad-spectrum neutron source and an array of pulse-shape-discriminating observation scintillators, a continuous measurement of the proton light yield was performed for EJ-309 (200 keV$-$3.2 MeV), EJ-276 (170 keV$-$4.9 MeV), and the organic glass (50 keV$-$20 MeV). Finally, the PSD properties of the organic glass, EJ-309, and EJ-276 were evaluated using an AmBe source and compared via a figure-of-merit metric. The organic glass exhibited a higher electron light output than both EJ-309 and EJ-276. Its proton light yield and PSD performance were comparable to EJ-309 and superior to that of EJ-276. With these performance characteristics, the organic glass scintillator is well poised to replace current state-of-the-art PSD-capable scintillators in a range of fast neutron detection applications.

physics.ins-det↗

arXiv2020

FIER: Software for analytical modeling of delayed gamma-ray spectra

A new software package, the Fission Induced Electromagnetic Response (FIER) code, has been developed to analytically predict delayed $γ$-ray spectra following fission. FIER uses evaluated nuclear data and solutions to the Bateman equations to calculate the time-dependent populations of fission products and their decay daughters resulting from irradiation of a fissionable isotope. These populations are then used in the calculation of $γ$-ray emission rates to obtain the corresponding delayed $γ$-ray spectra. FIER output was compared to experimental data obtained by irradiation of a $^{235}$U sample in the Godiva critical assembly. This investigation illuminated discrepancies in the input nuclear data libraries, showcasing the usefulness of FIER as a tool to address nuclear data deficiencies through comparison with experimental data. FIER provides traceability between $γ$-ray emissions and their contributing nuclear species, decay chains, and parent fission fragments, yielding a new capability for the nuclear science community.

physics.ins-det↗

arXiv2020

Proton Light Yield in Organic Scintillators using a Double Time-of-Flight Technique

Recent progress in the development of novel organic scintillators necessitates modern characterization capabilities. As the primary means of energy deposition by neutrons in these materials is n-p elastic scattering, knowledge of the proton light yield is paramount. This work establishes a new model-independent method to continuously measure proton light yield in organic scintillators over a broad energy range. Using a deuteron breakup neutron source at the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory and an array of organic scintillators, the proton light yield of EJ-301 and EJ-309, commercially available organic liquid scintillators from Eljen Technology, were measured via a double time-of-flight technique. The light yield was determined using a kinematically over-constrained system in the proton energy range of 1-20 MeV. The effect of pulse integration length on the magnitude and shape of the proton light yield relation was also explored. This work enables accurate simulation of the performance of advanced neutron detectors and supports the development of next-generation neutron imaging systems.

physics.ins-det↗

arXiv2020

Neutron Spectroscopy for Pulsed Beams with Frame Overlap using a Double Time-of-Flight Technique

A new double time-of-flight (dTOF) neutron spectroscopy technique has been developed for pulsed broad spectrum sources with a duty cycle that results in frame overlap, where fast neutrons from a given pulse overtake slower neutrons from previous pulses. Using a tunable beam at the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory, neutrons were produced via thick-target breakup of 16 MeV deuterons on a beryllium target in the cyclotron vault. The breakup spectral shape was deduced from a dTOF measurement using an array of EJ-309 organic liquid scintillators. Simulation of the neutron detection efficiency of the scintillator array was performed using both GEANT4 and MCNP6. The efficiency-corrected spectral shape was normalized using a foil activation technique to obtain the energy-dependent flux of the neutron beam at zero degrees with respect to the incoming deuteron beam. The dTOF neutron spectrum was compared to spectra obtained using HEPROW and GRAVEL pulse height spectrum unfolding techniques. While the unfolding and dTOF results exhibit some discrepancies in shape, the integrated flux values agree within two standard deviations. This method obviates neutron time-of-flight spectroscopy challenges posed by pulsed beams with frame overlap and opens new opportunities for pulsed white neutron source facilities.

physics.ins-det↗

arXiv2020

Low Energy Light Yield of Fast Plastic Scintillators

Compact neutron imagers using double-scatter kinematic reconstruction are being designed for localization and characterization of special nuclear material. These neutron imaging systems rely on scintillators with a rapid prompt temporal response as the detection medium. As n-p elastic scattering is the primary mechanism for light generation by fast neutron interactions in organic scintillators, proton light yield data are needed for accurate assessment of scintillator performance. The proton light yield of a series of commercial fast plastic organic scintillators---EJ-200, EJ-204, and EJ-208---was measured via a double time-of-flight technique at the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory. Using a tunable deuteron breakup neutron source, target scintillators housed in a dual photomultiplier tube configuration, and an array of pulse-shape-discriminating observation scintillators, the fast plastic scintillator light yield was measured over a broad and continuous energy range down to proton recoil energies of approximately 50 keV. This work provides key input to event reconstruction algorithms required for utilization of these materials in emerging neutron imaging modalities.

physics.ins-det↗

arXiv2020

Scintillator light yield measurements with waveform digitizers

The proton light yield of organic scintillators has been measured extensively in recent years using fast waveform digitizers and large discrepancies exist in the values reported by different authors. In this letter, we address principles of digital signal processing that must be considered when conducting scintillator light yield measurements. Digitized waveform pulse height values are only proportional to the amount of scintillation light if the temporal shape of the scintillation pulse is independent of the amount of energy deposited. This is not the case for scintillation pulses resulting from fast neutron interactions in organic scintillators. Authors measuring proton light yield should therefore report pulse integral values and ensure that the integration length is long enough to capture most of the scintillation light.

physics.ins-det↗

arXiv2019

Restricted spin-range correction in the Oslo Method: The example of nuclear level density and $γ$-ray strength function from $^{239}\mathrm{Pu}(\mathrm{d,p}γ)^{240}\mathrm{Pu}$

The Oslo Method has been applied to particle-$γ$ coincidences following the $^{239}\mathrm{Pu}$(d,p) reaction to obtain the nuclear level density (NLD) and $γ$-ray strength function ($γ$SF) of $^{240}\mathrm{Pu}$. The experiment was conducted with a 12 MeV deuteron beam at the Oslo Cyclotron Laboratory. The low spin transfer of this reaction leads to a spin-parity mismatch between populated and intrinsic levels. This is a challenge for the Oslo Method as it can have a significant impact on the extracted NLD and $γ$SF. We have developed an iterative approach to ensure consistent results even for cases with a large spin-parity mismatch, in which we couple Green's Function Transfer calculations of the spin-parity dependent population cross-section to the nuclear decay code RAINIER. The resulting $γ$SF shows a pronounced enhancement between 2-4 MeV that is consistent with the location of the low-energy orbital $M1$ scissors mode.

nucl-ex↗

arXiv2019

Impact of restricted spin-ranges in the Oslo Method: The example of (d,p)$^{240}\mathrm{Pu}$

In this paper we present the first systematic analysis of the impact of the populated vs. intrinsic spin distribution on the nuclear level density and $γ$-ray strength function retrieved through the Oslo Method. We illustrate the effect of the spin distribution on the recently performed $^{239}\mathrm{Pu}$(d,p$γ$)$^{240}\mathrm{Pu}$ experiment using a 12 MeV deuteron beam performed at the Oslo Cyclotron Lab. In the analysis we couple state-of-the-art calculations for the populated spin-distributions with the Monte-Carlo nuclear decay code RAINIER to compare Oslo Method results to the known input. We find that good knowledge of the populated spin distribution is crucial and show that the populated distribution has a significant impact on the extracted nuclear level density and $γ$-ray strength function for the $^{239}\mathrm{Pu}$(d,p$γ$)$^{240}\mathrm{Pu}$ case.

nucl-ex↗

arXiv2018

Radiative-capture cross sections for the $^{139}$La($n,γ$) reactionusing thermal neutrons and structural properties of $^{140}$La

A set of prompt partial $γ$-ray production cross sections from thermal neutron-capture were measured for the $^{139}$La($n,γ$) reaction using a guided beam of subthermal (thermal and cold) neutrons incident upon a $^{\rm nat}$La$_{2}$O$_{3}$ target at the Prompt Gamma Activation Analysis facility of the Budapest Research Reactor. Absolute $^{140}$La cross sections were determined relative to the well-known comparator $^{35}$Cl($n,γ$) cross sections from the irradiation of a stoichiometric $^{\rm nat}$LaCl$_{3}$ sample. The total cross section for radiative thermal neutron-capture on $^{139}$La from the sum of experimentally measured cross sections observed to directly feed the $^{140}$La ground state was determined to be $σ_{0}^{\rm expt} = 8.58(50)$ b. To assess completeness of the decay scheme and as a consistency check, the measured cross sections for transitions feeding the ground state from levels below a critical energy of $E_{c} = 285$ keV were combined with a modeled contribution accounting for ground-state feeding from the quasicontinuum to arrive at a total cross section of $σ_{0} = 9.36(74)$ b. In addition, a neutron-separation energy of $S_{n} = 5161.005(21)$ keV was determined from a least-squares fit of the measured primary $γ$-ray energies to the low-lying levels of the $^{140}$La decay scheme. Furthermore, several nuclear structure improvements are proposed for the decay scheme. The measured cross-section and separation-energy results are comparable to earlier measurements of these quantities.

nucl-ex↗

arXiv2016

Statistical properties of $^{243}$Pu, and $^{242}$Pu(n,$γ$) cross section calculation

The level density and gamma-ray strength function (gammaSF) of 243Pu have been measured in the quasi-continuum using the Oslo method. Excited states in 243Pu were populated using the 242Pu(d,p) reaction. The level density closely follows the constant-temperature level density formula for excitation energies above the pairing gap. The gammaSF displays a double-humped resonance at low energy as also seen in previous investigations of actinide isotopes. The structure is interpreted as the scissors resonance and has a centroid of omega_{SR}=2.42(5)MeV and a total strength of B_{SR}=10.1(15)mu_N^2, which is in excellent agreement with sum-rule estimates. The measured level density and gammaSF were used to calculate the 242Pu(n,gamma) cross section in a neutron energy range for which there were previously no measured data.

nucl-ex↗