arXiv subjects

B. Sassolas

Publications and source records attributed to B. Sassolas.

5 recordsLinked to original sources

arXiv2026

Progress of the design of the 12-m optical, Wide-field Spectroscopic Telescope (WST)

The Wide-Field Spectroscopic Telescope (WST) is a 12-m class, Alt-Az optical telescope providing two simultaneous foci, 2 degrees and 3 by 3 arc minutes respectively, for Multi-Object Spectroscopy (MOS) and Integral Field Spectroscopy (IFS) at visible wavelengths. Within the framework of the Horizon Programme, the project has been approved for phase A funding by the EC in 2024 and is currently undergoing intensive development. The optical design relies on a corrected Cassegrain solution feeding multi-object spectrographs through fibres, while the central area of the field is propagated to a gravity-stable Integral Field Station housing an array of spectrographs. We report progress of the design, of the functional and physical definitions of key subsystems, and of the design of high-performance coatings of the telescope optics. The telescope would be located near ESO Paranal - Armazones observatory and protected by a VLT-like enclosure. With a view to minimising risks, from capital investment to operations, designs build extensively on VLT and ELT solutions. Owing to the optical configuration, the telescope can be wavefront-controlled at both foci, with little if any crosstalk between MOS and IFS controls. The optical path is constrained to provide natural guide star, ground-layer adaptive correction at the IFS field, within existing technology. Finally, from its earliest stage of development the system is being scrutinized for its properties in relation to sustainability.

astro-ph.IM↗

arXiv2026

Experimental Realization of Optimized Ternary Mirror Coatings

We report on the first experimental realization of multi-material dielectric mirror coatings designed through a multi-objective optimization algorithm to simultaneously minimize thermal noise and optical losses. We validate this design strategy by fabricating and characterizing two distinct ternary systems: a SiNx -based proof-of-concept and a Ti:GeO2 -based system targeting lower optical losses. The performance of the SiN x coating shows remarkable agreement with predictions, demonstrating a noise amplitude spectral density reduction of 0.82 with respect to current reference coatings, and validating our design-to-fabrication pipeline. The Ti:GeO2 -based system achieves the crucial goal of sub-ppm absorption; its measured thermal noise, however, is higher than the theoretically predicted level of 0.71, extrapolated from single-layer material characterization. A dedicated tolerance analysis confirms that this discrepancy is not attributable to random thickness errors, emphasizing that further studies of the manufacturing process are needed to fully exploit this combination of materials. This work establishes a robust methodology for producing complex, high-performance optical coatings tailored for precision experiments.

physics.optics↗

arXiv2024

Development of ion-beam sputtered silicon nitride thin films for low-noise mirror coatings of gravitational-wave detectors

Brownian thermal noise of thin-film coatings is a fundamental limit for high-precision experiments based on optical resonators such as gravitational-wave interferometers. Here we present the results of a research activity aiming to develop lower-noise ion-beam sputtered silicon nitride thin films compliant with the very stringent requirements on optical loss of gravitational-wave interferometers. In order to test the hypothesis of a correlation between the synthesis conditions of the films and their elemental composition and optical and mechanical properties, we varied the voltage, current intensity and composition of the sputtering ion beam, and we performed a broad campaign of characterizations. While the refractive index was found to monotonically depend on the beam voltage and linearly vary with the N/Si ratio, the optical absorption appeared to be strongly sensitive to other factors, as yet unidentified. However, by systematically varying the deposition parameters, an optimal working point was found. Thus we show that the loss angle and extinction coefficient of our thin films can be as low as $(1.0 \pm 0.1) \times 10^{-4}$ rad at $\sim$2.8 kHz and $(6.4 \pm 0.2) \times 10^{-6}$ at 1064 nm, respectively, after thermal treatment at 900 $^{\circ}$C. To the best of our knowledge, such loss angle value is the lowest ever measured on this class of thin films. We then used our silicon nitride thin films to design and produce a multi-material mirror coating showing a thermal noise amplitude of $(10.3 \pm 0.2) \times 10^{-18}$ m Hz$^{-1/2}$ at 100 Hz, which is 25\% lower than in current mirror coatings of the Advanced LIGO and Advanced Virgo interferometers, and an optical absorption as low as $(1.6 \pm 0.5)$ parts per million at 1064 nm.

physics.ins-det↗

arXiv2021

Exploration of co-sputtered Ta$_2$O$_5$-ZrO$_2$ thin films for gravitational-wave detectors

We report on the development and extensive characterization of co-sputtered tantala-zirconia thin films, with the goal to decrease coating Brownian noise in present and future gravitational-wave detectors. We tested a variety of sputtering processes of different energies and deposition rates, and we considered the effect of different values of cation ratio $\eta =$ Zr/(Zr+Ta) and of post-deposition heat treatment temperature $T_a$ on the optical and mechanical properties of the films. Co-sputtered zirconia proved to be an efficient way to frustrate crystallization in tantala thin films, allowing for a substantial increase of the maximum annealing temperature and hence for a decrease of coating mechanical loss. The lowest average coating loss was observed for an ion-beam sputtered sample with $\eta = 0.485 \pm 0.004$ annealed at 800 $^{\circ}$C, yielding $\overline{\varphi} = 1.8 \times 10^{-4}$. All coating samples showed cracks after annealing. Although in principle our measurements are sensitive to such defects, we found no evidence that our results were affected. The issue could be solved, at least for ion-beam sputtered coatings, by decreasing heating and cooling rates down to 7 $^{\circ}$C/h. While we observed as little optical absorption as in the coatings of current gravitational-wave interferometers (0.5 parts per million), further development will be needed to decrease light scattering and avoid the formation of defects upon annealing.

physics.ins-det↗

arXiv2021

Optical and mechanical properties of ion-beam-sputtered Nb$_2$O$_5$ and TiO$_2$-Nb$_2$O$_5$ thin films for gravitational-wave interferometers

Brownian thermal noise associated with highly-reflective mirror coatings is a fundamental limit for several precision experiments, including gravitational-wave detectors. Recently, there has been a worldwide effort to find mirror coatings with improved thermal noise properties that also fulfill strict optical requirements such as low absorption and scatter. We report on the optical and mechanical properties of ion-beam-sputtered niobia and titania-niobia thin films, and we discuss application of such coatings in current and future gravitational-wave detectors. We also report an updated direct coating thermal noise measurement of the HR coatings used in Advanced LIGO and Advanced Virgo.

physics.ins-det↗