arXiv subjects

Baleegh Abdo

Publications and source records attributed to Baleegh Abdo.

At least 19 recordsLinked to original sources

arXiv2026

Enhancing qubit readout fidelity with two-mode squeezing of the coherent measurement signal

The ability to perform high-fidelity quantum nondemolition qubit readout is pivotal for the realization of large and powerful quantum computers. Such readout of superconducting qubits is generally enabled by amplifying the weak dispersive measurement signals using phase-preserving quantum-limited Josephson amplifiers with sufficient gain to dilute the contribution of the added noise by the output chain. Here, we further enhance the qubit readout fidelity by (1) simultaneously measuring the two-mode squeezed states of the amplified readout signals at the signal and idler frequencies of the nondegenerate amplifier and (2) coherently combining them at the classical processing stage following a relative rotation that maximizes the signal to noise ratio of the qubit-encoded readout quadrature. Such readout scheme exhibits enhancement in the readout fidelity for all practical values of amplifier gain and noise added by the output chain and is fully compatible with frequency multiplexed setups used in large quantum processors.

quant-ph↗

arXiv2025

Nondegenerate Josephson Mixers with Enhanced Bandwidth and Saturation Power for Quantum Signal Amplification and Transduction

Nondegenerate Josephson mixers (JMs), formed by coupling two different transmission-line resonators to Josephson ring modulators (JRMs), are vital and versatile devices capable of processing microwave signals at the quantum limit. Owing to the lossless nondegenerate three-wave mixing process enabled by the JRM, JMs can perform phase preserving amplification of quantum signals, generate two-mode squeezed states, and perform noiseless frequency conversion. However, due to their limited bandwidth and saturation power, such resonator-based JMs are generally unable to simultaneously process frequency-multiplexed signals required in large quantum processors. To overcome this longstanding dual challenge, we redesign the JRM parameters by optimizing its inductances to suppress higher order mixing products and engineer its electromagnetic environment by incorporating lumped-element coupled-mode networks between the JRM and the two distinct ports of the JM. By implementing these strategies, we measure for JMs realized with four coupled modes per port, operated in amplification (conversion), bandwidths of about 400 MHz (700 MHz) with power reflections above 10 dB (below -10 dB) and saturation powers of about -110 dBm at 15 dB (-91 dBm at -26 dB). Similarly, we demonstrate for a low external quality factor resonant-mode JM operated in conversion, a maximum bandwidth of about $670$ MHz with power reflections below -10 dB and a maximum saturation power of about -86 dBm at -17 dB. Such nondegenerate JMs with enhanced bandwidths and saturation powers could serve in a variety of frequency-multiplexed settings ranging from high fidelity qubit readout and unidirectional routing of quantum signals to generation of remote entanglement with continuous variables.

quant-ph↗

arXiv2025

Teleportation and Entanglement Swapping of Continuous Quantum Variables of Microwave Radiation

Quantum communication is needed to build powerful quantum computers and establish reliable quantum networks. At its basis lies the ability to generate and distribute entanglement to separate quantum systems, which can be used to run remote quantum operations on them or teleport quantum states from one system to another with the help of classical channels. To this end, it is useful to harness the resource of continuous-variable (CV) entanglement since it can be efficiently and unconditionally produced by squeezing light in a nonlinear medium and can be easily manipulated, distributed, and measured using standard components. While various aspects of CV-based quantum communication have been successfully demonstrated in the optical domain, some key capabilities, such as entanglement swapping, have been lacking in the microwave domain. Here, we demonstrate three key elements of CV-based microwave quantum communication, (1) a Josephson mixer operating as nondegenerate two-mode entangler with maximum measured logarithmic negativity E_N=1.5, (2) a quantum teleportation apparatus, capable of teleporting vacuum and coherent states with a maximum fidelity of 73%, which exceeds the 50% classical limit and is mainly limited by intermediate losses in the setup, and (3) an entanglement swapping system which generates entanglement between two remote noninteracting modes via entanglement swapping operations applied to input vacuum and coherent states with maximum measured logarithmic negativity E_N=0.53. Such hardware-efficient CV entanglement building blocks that are based on nondegenerate Josephson mixers could enable wide-ranging applications in modular quantum computation, quantum cryptography, and quantum communication.

quant-ph↗

arXiv2022

Weakly Flux-Tunable Superconducting Qubit

Flux-tunable qubits are a useful resource for superconducting quantum processors. They can be used to perform cPhase gates, facilitate fast reset protocols, avoid qubit-frequency collisions in large processors, and enable certain fast readout schemes. However, flux-tunable qubits suffer from a trade-off between their tunability range and sensitivity to flux noise. Optimizing this trade-off is particularly important for enabling fast, high-fidelity, all-microwave cross-resonance gates in large, high-coherence processors. This is mainly because cross-resonance gates set stringent conditions on the frequency landscape of neighboring qubits, which are difficult to satisfy with non-tunable transmons due to their relatively large fabrication imprecision. To solve this problem, we realize a coherent, flux-tunable, transmon-like qubit, which exhibits a frequency tunability range as small as 43 MHz, and whose frequency, anharmonicity and tunability range are set by a few experimentally achievable design parameters. Such a weakly tunable qubit is useful for avoiding frequency collisions in a large lattice while limiting its susceptibility to flux noise.

quant-ph↗

arXiv2021

High-fidelity qubit readout using interferometric directional Josephson devices

Nonreciprocal microwave devices, such as circulators and isolators, are needed in high-fidelity qubit readout schemes to unidirectionally route the readout signals and protect the qubits against noise coming from the output chain. However, cryogenic circulators and isolators are prohibitive in scalable superconducting architectures because they rely on magnetic materials. Here, we perform a fast (750 ns) high-fidelity (95%) quantum nondemolition readout of a coherent superconducting qubit ($T_{1}=52$ $μs$, $T_{\rm{2E}}=35$ $μs$) without any nonreciprocal magnetic devices. We employ in our readout chain a microwave-controlled qubit-Readout Multi-Chip Module (qRMCM) that integrates interferometric directional Josephson devices consisting of an isolator and a reconfigurable isolator/amplifier device and an off-chip low-pass filter. Using the qRMCM, we demonstrate isolation up to 45 dB within 13 MHz, when both directional devices are operated as isolators, and low-noise amplification in excess of 10 dB within a dynamical bandwidth of $10$ MHz, when the reconfigurable device is operated as an amplifier. We also demonstrate using the variable isolation of the qRMCM an in-situ enhancement of the qubit coherence times $T_{\rmφ}$ and $T_{\rm{2E}}$ by two orders of magnitude (i.e., from $T_{\rmφ}=T_{\rm{2E}}=0.5$ $μs$ to $T_{\rmφ}=90$ $μs$ and $T_{\rm{2E}}=50$ $μs$). Furthermore, by directly comparing the qRMCM performance to a state-of-art configuration (with $T_{\rm{2E}}\approx 2T_{1}$) that employs a pair of wideband magnetic isolators, we find that the excess pure dephasing measured with the qRMCM (for which $T_{\rm{2E}}\approx T_{1}$) is likely limited by residual thermal photon population in the readout resonator. Improved versions of the qRMCM could replace magnetic circulators and isolators in large superconducting quantum processors.

quant-ph↗

arXiv2018

Active protection of a superconducting qubit with an interferometric Josephson isolator

Nonreciprocal microwave devices play several critical roles in high-fidelity, quantum-nondemolition (QND) measurement schemes. They separate input from output, impose unidirectional routing of readout signals, and protect the quantum systems from unwanted noise originated by the output chain. However, state-of-the-art, cryogenic circulators and isolators are disadvantageous in scalable superconducting quantum processors because they use magnetic materials and strong magnetic fields. Here, we realize an active isolator formed by coupling two nondegenerate Josephson mixers in an interferometric scheme. Nonreciprocity is generated by applying a phase gradient between the same-frequency pumps feeding the Josephson mixers, which play the role of the magnetic field in a Faraday medium. To demonstrate the applicability of this Josephson-based isolator for quantum measurements, we incorporate it into the output line of a superconducting qubit, coupled to a fast resonator and a Purcell filter. We also utilize a wideband, superconducting directional coupler for coupling the readout signals into and out of the qubit-resonator system and a quantum-limited Josephson amplifier for boosting the readout fidelity. By using this novel quantum setup, we demonstrate fast, high-fidelity, QND measurements of the qubit while providing more than 20 dB of protection against amplified noise reflected off the Josephson amplifier.

quant-ph↗

arXiv2017

Characterization of hidden modes in networks of superconducting qubits

We present a method for detecting electromagnetic (EM) modes that couple to a superconducting qubit in a circuit-QED architecture. Based on measurement-induced dephasing, this technique allows the measurement of modes that have a high quality factor (Q) and may be difficult to detect through standard transmission and reflection measurements at the device ports. In this scheme the qubit itself acts as a sensitive phase meter, revealing modes that couple to it through measurements of its coherence time. Such modes are indistinguishable from EM modes that do not couple to the qubit using a vector network analyzer. Moreover, this technique provides useful characterization parameters including the quality factor and the coupling strength of the unwanted resonances. We demonstrate the method for detecting both high-Q coupling resonators in planar devices as well as spurious modes produced by a 3D cavity.

quant-ph↗

arXiv2017

Multi-Path Interferometric Josephson Directional Amplifier for Qubit Readout

We realize and characterize a quantum-limited, directional Josephson amplifier suitable for qubit readout. The device consists of two nondegenerate, three-wave-mixing amplifiers that are coupled together in an interferometric scheme, embedded in a printed circuit board. Nonreciprocity is generated by applying a phase gradient between the same-frequency pumps feeding the device, which plays the role of the magnetic field in a Faraday medium. Directional amplification and reflection-gain elimination are induced via wave interference between multiple paths in the system. We measure and discuss the main figures of merit of the device and show that the experimental results are in good agreement with theory. An improved version of this directional amplifier is expected to eliminate the need for bulky, off-chip isolation stages that generally separate quantum systems and preamplifiers in high-fidelity, quantum-nondemolition measurement setups.

physics.ins-det↗

arXiv2017

Gyrator operation using Josephson mixers

Nonreciprocal microwave devices, such as circulators, are useful in routing quantum signals in quantum networks and protecting quantum systems against noise coming from the detection chain. However, commercial, cryogenic circulators, now in use, are unsuitable for scalable superconducting quantum architectures due to their appreciable size, loss, and inherent magnetic field. We report on the measurement of a key nonreciprocal element, i.e., the gyrator, which can be used to realize a circulator. Unlike state-of-the-art gyrators, which use a magneto-optic effect to induce a phase shift of $π$ between transmitted signals in opposite directions, our device uses the phase nonreciprocity of a Josephson-based three-wave-mixing device. By coupling two of these mixers and operating them in noiseless frequency-conversion mode, we show that the device acts as a nonreciprocal phase shifter whose phase shift is controlled by the phase difference of the microwave tones driving the mixers. Such a device could be used to realize a lossless, on-chip, superconducting circulator suitable for quantum-information-processing applications.

cond-mat.supr-con↗

arXiv2017

Demonstration of weight-four parity measurements in the surface code architecture

We present parity measurements on a five-qubit lattice with connectivity amenable to the surface code quantum error correction architecture. Using all-microwave controls of superconducting qubits coupled via resonators, we encode the parities of four data qubit states in either the $X$- or the $Z$-basis. Given the connectivity of the lattice, we perform full characterization of the static $Z$-interactions within the set of five qubits, as well as dynamical $Z$-interactions brought along by single- and two-qubit microwave drives. The parity measurements are significantly improved by modifying the microwave two-qubit gates to dynamically remove non-ideal $Z$ errors.

quant-ph↗

arXiv2016

Time-multiplexed amplification in a hybrid-less and coil-less Josephson parametric converter

Josephson parametric converters (JPCs) are superconducting devices capable of performing nondegenerate, three-wave mixing in the microwave domain without losses. One drawback limiting their use in scalable quantum architectures is the large footprint of the auxiliary circuit needed for their operation, in particular, the use of off-chip, bulky, broadband hybrids and magnetic coils. Here, we realize a JPC which eliminates the need for these bulky components. The pump drive and flux bias are applied in the new device through an on-chip, lossless, three-port power divider and on-chip flux line, respectively. We show that the new design considerably simplifies the circuit and reduces the footprint of the device while maintaining a comparable performance to state-of-the-art JPCs. Furthermore, we exploit the tunable bandwidth property of the JPC and the added capability of applying alternating currents to the flux line in order to switch the resonance frequencies of the device, hence demonstrating time-multiplexed amplification of microwave tones that are separated by more than the dynamical bandwidth of the amplifier. Such a measurement technique can potentially serve to perform time-multiplexed, high-fidelity readout of superconducting qubits.

cond-mat.supr-con↗

arXiv2014

Non-Poissonian Quantum Jumps of a Fluxonium Qubit due to Quasiparticle Excitations

As the energy relaxation time of superconducting qubits steadily improves, non-equilibrium quasiparticle excitations above the superconducting gap emerge as an increasingly relevant limit for qubit coherence. We measure fluctuations in the number of quasiparticle excitations by continuously monitoring the spontaneous quantum jumps between the states of a fluxonium qubit, in conditions where relaxation is dominated by quasiparticle loss. Resolution on the scale of a single quasiparticle is obtained by performing quantum non-demolition projective measurements within a time interval much shorter than $T_1$, using a quantum limited amplifier (Josephson Parametric Converter). The quantum jumps statistics switches between the expected Poisson distribution and a non-Poissonian one, indicating large relative fluctuations in the quasiparticle population, on time scales varying from seconds to hours. This dynamics can be modified controllably by injecting quasiparticles or by seeding quasiparticle-trapping vortices by cooling down in magnetic field.

quant-ph↗

arXiv2013

Josephson directional amplifier for quantum measurement of superconducting circuits

We have realized a microwave quantum-limited amplifier that is directional and can therefore function without the front circulator needed in many quantum measurements. The amplification takes place in only one direction between the input and output ports. Directionality is achieved by multi-pump parametric amplification combined with wave interference. We have verified the device noise performances by using it to readout a superconducting qubit and observed quantum jumps. With an improved version of this device, qubit and preamplifer could be integrated on the same chip.

cond-mat.supr-con↗

arXiv2013

Directional amplification with a Josephson circuit

Non-reciprocal devices, which have different transmission coefficients for propagating waves in opposite directions, are crucial components in many low noise quantum measurements. In most schemes, magneto-optical effects provide the necessary non-reciprocity. In contrast, the proof-of-principle device presented here, consists of two on-chip coupled Josephson parametric converters (JPCs), which achieves directionality by exploiting the non-reciprocal phase response of the JPC in the trans-gain mode. The non-reciprocity of the device is controlled in-situ by varying the amplitude and phase difference of two independent microwave pump tones feeding the system. At the desired working point and for a signal frequency of 8.453 GHz, the device achieves a forward power gain of 15 dB within a dynamical bandwidth of 9 MHz, a reverse gain of -6 dB and suppression of the reflected signal by 8 dB. We also find that the amplifier adds a noise equivalent to less than one and a half photons at the signal frequency (referred to the input). It can process up to 3 photons at the signal frequency per inverse dynamical bandwidth. With a directional amplifier operating along the principles of this device, qubit and readout preamplifier could be integrated on the same chip.

cond-mat.supr-con↗

arXiv2012

Full coherent frequency conversion between two microwave propagating modes

We demonstrate full frequency conversion in the microwave domain using a Josephson three-wave mixing device pumped at the difference between the frequencies of its fundamental eigenmodes. By measuring the signal output as a function of the intensity and phase of the three input signal, idler and pump tones, we show that the device functions as a controllable three-wave beam-splitter/combiner for propagating microwave modes, in accordance with theory. Losses at the full conversion point are found to be less than 10^-2. Potential applications of the device include quantum information transduction and realization of an ultra-sensitive interferometer with controllable feedback.

cond-mat.supr-con↗

arXiv2012

Non-degenerate, three-wave mixing with the Josephson ring modulator

The Josephson ring modulator (JRM) is a device, based on Josephson tunnel junctions, capable of performing non-degenerate mixing in the microwave regime without losses. The generic scattering matrix of the device is calculated by solving coupled quantum Langevin equations. Its form shows that the device can achieve quantum-limited noise performance both as an amplifier and a mixer. Fundamental limitations on simultaneous optimization of performance metrics like gain, bandwidth and dynamic range (including the effect of pump depletion) are discussed. We also present three possible integrations of the JRM as the active medium in a different electromagnetic environment. The resulting circuits, named Josephson parametric converters (JPC), are discussed in detail, and experimental data on their dynamic range are found to be in good agreement with theoretical predictions. We also discuss future prospects and requisite optimization of JPC as a preamplifier for qubit readout applications.

cond-mat.supr-con↗

arXiv2011

Josephson Amplifier for Qubit Readout

We report on measurements of a Josephson amplifier (J-amp) suitable for quantum-state qubit readout in the microwave domain. It consists of two microstrip resonators which intersect at a Josephson ring modulator. A maximum gain of about 20 dB, a bandwidth of 9 MHz, and a center-frequency tunability of about 60 MHz with gain in excess of 10 dB have been attained for idler and signal of frequencies 6.4 GHz and 8.1 GHz, in accordance with theory. Maximum input power measurements of the J-amp show a relatively good agreement with theoretical prediction. We discuss how the amplifier characteristics can be improved.

cond-mat.supr-con↗

arXiv2009

Intermode Dephasing in a Superconducting Stripline Resonator

We study superconducting stripline resonator (SSR) made of Niobium, which is integrated with a superconducting interference device (SQUID). The large nonlinear inductance of the SQUID gives rise to strong Kerr nonlinearity in the response of the SSR, which in turn results in strong coupling between different modes of the SSR. We experimentally demonstrate that such intermode coupling gives rise to dephasing of microwave photons. The dephasing rate depends periodically on the external magnetic flux applied to the SQUID, where the largest rate is obtained at half integer values (in units of the flux quantum). To account for our result we compare our findings with theory and find good agreement. Supplementary info at arXiv:0901.3133 .

cond-mat.supr-con↗