arXiv subjects

Bertrand Baudouy

Publications and source records attributed to Bertrand Baudouy.

5 recordsLinked to original sources

arXiv2026

Quench Protection in Insulated REBCO Conductors: Design Optimization and Fast Detection via REBCO SQD

This work was conducted within the framework of the exploratory French project PEPR SupraFusion, which aims to advance the field of fusion energy by developing High-Temperature Superconductor (HTS)-based demonstrators capable of storing significant energy while operating under high magnetic fields and currents. Ensuring a reliable protection during a quench in Insulated REBCO conductors is challenging\,: slow normal-zone propagation and validation delays allow the hotspot's temperature to reach damaging levels. We compare (i) conductor protection via copper-stabilizer optimization and (ii) a co-wound, REBCO superconducting quench detector (SQD) that is electrically isolated yet thermally coupled and intentionally deoxygenated to lower Tc and Ic for an earlier transition. Onedimensional THEA modeling shows that a good choice of stabilizer cross-section makes the protection possible during quench events by keeping the temperature of the hotspot within a safe limit. The simulations also demonstrate that the use of a REBCO SQD enables the quench detection at lower temperatures.

cond-mat.supr-con↗

arXiv2024

Experimental study of second sound quench detection for superconducting cavities

Superconducting RF cavities are used in particle accelerators to provide energy to the particle beam. Such cavities are mostly fabricated in niobium and often operated in superfluid helium. One of their limits of operation is the appearance of a local quench, initiated by a local field enhancement due to a defect, which leads to a normal conducting transition of the cavity. Localizing the quench area can be achieved with temperature mapping systems. Another method is the use of second sound wave propagation in superfluid helium. Measuring the time of propagation of these waves from quench location to special sensors, called Oscillating Superleak Transducers (OSTs), and using their well-known velocity should allow trilateration. However, most of experimental measurements on cavities show "premature signals", i.e. the second sound signals arrive earlier on the OSTs than expected. This paper presents several quench experiments on cavities equipped with OSTs and temperature mapping quench detection systems. Two hypotheses can explain the observed premature signals. The first one assesses faster propagation in helium. An experimental setup has been developed for testing this hypothesis, where second sound is created by a localized heater in a controlled environment up to 4.3 kW/cm2 and 2.8 J. Premature signals could not be verified in this setup. A second hypothesis based on a simple model including several processes in niobium and second sound propagation in helium is discussed. The model improves significantly the prediction of the times of arrival of the second sound waves. The overall study shows that the processes in niobium play a prominent role in the second sound detection for superconducting cavities.

physics.acc-ph↗

arXiv2022

High Field Magnet Development for HEP in Europe: A Proposal from LDG HFM Expert Panel

The European Laboratory Directors Group (LDG) was mandated by CERN Council in 2021 to oversee the development of an Accelerator R&D Roadmap. To this end, a set of expert panels was convened, covering the five broad areas of accelerator R&D highlighted in the ESPPU. The High Field Magnet (HFM) Panel is proposing a programme to demonstrate Nb3Sn magnet technology for large-scale deployment and to investigate the suitability of high temperature superconductors (HTS) for accelerator magnet applications. A summary of this programme is presented here.

physics.acc-ph↗

arXiv2022

Millisecond Time-Scale Measurements of Heat Transfer to an Open Bath of He II

We explore steady state and transient heat transfer from a narrow, rectangular stainless steel heater strip cooled from one side by an open bath of He~II. Setup validation is done by fitting the Kapitza heat transfer expression $Q = a_\mathrm{K} \left( {T_\mathrm{s}}^{n_\mathrm{K}} - {T_\mathrm{b}}^{n_\mathrm{K}} \right)$ to steady state measurements, finding fit parameters within the expected range; $a_\mathrm{K}$ = 1316.8$\pm10\%$ $\mathrm{W}\mathrm{m}^{-2}\mathrm{K}^{-1}$, $n_\mathrm{K}$ = 2.528$\pm10\%$. We find critical heat flux in line with estimates from literature, and the time between a step in heating and the onset of film boiling follows the expected $\propto Q^{-4}$ dependence. During the first millisecond after a step in applied heating power density our measurements show a slower thermal rise time than that found by a time-dependent one-dimensional model of our setup using the steady state Kapitza heat transfer expression as the cooling boundary condition. However, the results compare favourably with transient measurements in literature. After the first millisecond, agreement between measurement and model is excellent. We do not find conclusive evidence of an orientation dependence of the Kapitza heat transfer mechanism, nor heat transfer differences that can be attributed to local surface variations along the same heater.

physics.app-ph↗

arXiv2022

Millisecond Time-Scale Measurements of Heat Transfer to Confined He II

We explore transient heat transfer, on the millisecond time-scale, from a narrow, rectangular stainless steel heater cooled from one side by He II confined to a channel of 120 $μ$m depth. The helium is isolated from the external bath with the exception of two pin-holes of cross section about 10% that of the channel. We measure the temperatures of both the heater strip and the channel helium during slow-pulse heating that reaches peak power after 9 ms, fast-pulse heating that reaches peak power after 100 $μ$s, and step heating that reaches steady power after 100 $μ$s. Using the steady state Kapitza heat transfer expression at the interface between heater and helium, and the Gorter-Mellink heat transfer regime in the helium channel, we obtain excellent agreement between simulation and measurement during the first 5 ms of slow-pulse tests. Using instead the measured helium temperature in the Kapitza expression, we obtain excellent agreement between the simulated and measured heater response during the first 150 ms of slow-pulse tests. The same model fails to explain the fast-pulse transient response of the heater and helium, while it can explain the helium response to a step in applied power but not the heater response. The steady state Kapitza expression may therefore not be applicable to heating events that are over within a single millisecond.

physics.app-ph↗