arXiv subjects

Boris Korzh

Publications and source records attributed to Boris Korzh.

At least 37 records · Page 2Linked to original sources

arXiv2024

Improvements of readout signal integrity in mid-infrared superconducting nanowire single photon detectors

Superconducting nanowire single-photon detectors (SNSPDs) with high timing resolution and low background counts in the mid infrared (MIR) have the potential to open up numerous opportunities in fields such as exoplanet searches, direct dark matter detection, physical chemistry, and remote sensing. One challenge in pushing SNSPD sensitivity to the MIR is a decrease in the signal-to-noise ratio (SNR) of the readout signal as the critical currents become increasingly smaller. We overcome this trade-off with a new device architecture that employs impedance matching tapers and superconducting nanowire avalanche photodetectors to demonstrate increased SNR while maintaining saturated internal detection efficiency at 7.4 μm and getting close to saturation at 10.6 μm. This work provides a novel platform for pushing SNSPD sensitivity to longer wavelengths while improving the scalability of the readout electronics.

physics.ins-det↗

arXiv2023

High-dimensional time-frequency entanglement in a singly-filtered biphoton frequency comb

High-dimensional quantum entanglement is a cornerstone for advanced technology enabling large-scale noise-tolerant quantum systems, fault-tolerant quantum computing, and distributed quantum networks. The recently developed biphoton frequency comb (BFC) provides a powerful platform for high-dimensional quantum information processing in its spectral and temporal quantum modes. Here we propose and generate a singly-filtered high-dimensional BFC via spontaneous parametric down-conversion by spectrally shaping only the signal photons with a Fabry-Perot cavity. High-dimensional energy-time entanglement is verified through Franson-interference recurrences and temporal correlation with low-jitter detectors. Frequency- and temporal- entanglement of our singly-filtered BFC is then quantified by Schmidt mode decomposition. Subsequently, we distribute the high-dimensional singly-filtered BFC state over a 10 km fiber link with a post-distribution time-bin dimension lower bounded to be at least 168. Our demonstrations of high-dimensional entanglement and entanglement distribution show the capability of the singly-filtered quantum frequency comb for high-efficiency quantum information processing and high-capacity quantum networks.

quant-ph↗

arXiv2023

Low-noise single-photon counting superconducting nanowire detectors at infrared wavelengths up to 29 $μ$m

We report on the extension of the spectral sensitivity of superconducting nanowire single-photon detectors to a wavelength of 29 $μ$m. This represents the first demonstration of a time correlated single-photon counting detector at these long infrared wavelengths. We achieve saturated internal detection efficiency from 10 to 29 $μ$m, whilst maintaining dark count rates below 0.1 counts per second. Extension of superconducting nanowire single-photon detectors to this spectral range provides low noise and high timing resolution photon counting detection, effectively providing a new class of single-photon sensitive detector for these wavelengths. These detectors are important for applications such as exoplanet spectroscopy, infrared astrophysics, physical chemistry, remote sensing and direct dark-matter detection.

quant-ph↗

arXiv2023

A superconducting-nanowire single-photon camera with 400,000 pixels

For the last 50 years, superconducting detectors have offered exceptional sensitivity and speed for detecting faint electromagnetic signals in a wide range of applications. These detectors operate at very low temperatures and generate a minimum of excess noise, making them ideal for testing the non-local nature of reality, investigating dark matter, mapping the early universe, and performing quantum computation and communication. Despite their appealing properties, however, there are currently no large-scale superconducting cameras - even the largest demonstrations have never exceeded 20 thousand pixels. This is especially true for one of the most promising detector technologies, the superconducting nanowire single-photon detector (SNSPD). These detectors have been demonstrated with system detection efficiencies of 98.0%, sub-3-ps timing jitter, sensitivity from the ultraviolet (250nm) to the mid-infrared (10um), and dark count rates below 6.2e-6 counts per second (cps), but despite more than two decades of development they have never achieved an array size larger than a kilopixel. Here, we report on the implementation and characterization of a 400,000 pixel SNSPD camera, a factor of 400 improvement over the previous state-of-the-art. The array spanned an area 4x2.5 mm with a 5x5um resolution, reached unity quantum efficiency at wavelengths of 370 nm and 635 nm, counted at a rate of 1.1e5 cps, and had a dark count rate of 1e-4 cps per detector (corresponding to 0.13 cps over the whole array). The imaging area contains no ancillary circuitry and the architecture is scalable well beyond the current demonstration, paving the way for large-format superconducting cameras with 100% fill factors and near-unity detection efficiencies across a vast range of the electromagnetic spectrum.

quant-ph↗

arXiv2023

Entangled Photon Pair Source Demonstrator using the Quantum Instrumentation Control Kit System

We report the first demonstration of using the Quantum Instrumentation and Control Kit (QICK) system on RFSoCFPGA technology to drive an entangled photon pair source and to detect the photon signals. With the QICK system, we achieve high levels of performance metrics including coincidence-to-accidental ratio exceeding 150, and entanglement visibility exceeding 95%, consistent with performance metrics achieved using conventional waveform generators. We also demonstrate simultaneous detector readout using the digitization functional of QICK, achieving internal system synchronization time resolution of 3.2 ps. The work reported in this paper represents an explicit demonstration of the feasibility for replacing commercial waveform generators and time taggers with RFSoC-FPGA technology in the operation of a quantum network, representing a cost reduction of more than an order of magnitude.

quant-ph↗

arXiv2023

Large active-area superconducting microwire detector array with single-photon sensitivity in the near-infrared

Superconducting nanowire single photon detectors (SNSPDs) are the highest-performing technology for time-resolved single-photon counting from the UV to the near-infrared. The recent discovery of single-photon sensitivity in micrometer-scale superconducting wires is a promising pathway to explore for large active area devices with application to dark matter searches and fundamental physics experiments. We present 8-pixel $1 mm^2$ superconducting microwire single photon detectors (SMSPDs) with $1\,\mathrm{μm}$-wide wires fabricated from WSi and MoSi films of various stoichiometries using electron-beam and optical lithography. Devices made from all materials and fabrication techniques show saturated internal detection efficiency at 1064 nm in at least one pixel, and the best performing device made from silicon-rich WSi shows single-photon sensitivity in all 8 pixels and saturated internal detection efficiency in 6/8 pixels. This detector is the largest reported active-area SMSPD or SNSPD with near-IR sensitivity published to date, and the first report of an SMSPD array. By further optimizing the photolithography techniques presented in this work, a viable pathway exists to realize larger devices with $cm^2$-scale active area and beyond.

physics.ins-det↗

arXiv2023

Improved heralded single-photon source with a photon-number-resolving superconducting nanowire detector

Deterministic generation of single photons is essential for many quantum information technologies. A bulk optical nonlinearity emitting a photon pair, where the measurement of one of the photons heralds the presence of the other, is commonly used with the caveat that the single-photon emission rate is constrained due to a trade-off between multiphoton events and pair emission rate. Using an efficient and low noise photon-number-resolving superconducting nanowire detector we herald, in real time, a single photon at telecommunication wavelength. We perform a second-order photon correlation $g^{2}(0)$ measurement of the signal mode conditioned on the measured photon number of the idler mode for various pump powers and demonstrate an improvement of a heralded single-photon source. We develop an analytical model using a phase-space formalism that encompasses all multiphoton effects and relevant imperfections, such as loss and multiple Schmidt modes. We perform a maximum-likelihood fit to test the agreement of the model to the data and extract the best-fit mean photon number $μ$ of the pair source for each pump power. A maximum reduction of $0.118 \pm 0.012$ in the photon $g^{2}(0)$ correlation function at $μ= 0.327 \pm 0.007$ is obtained, indicating a strong suppression of multiphoton emissions. For a fixed $g^{2}(0) = 7e-3$, we increase the single pair generation probability by 25%. Our experiment, built using fiber-coupled and off-the-shelf components, delineates a path to engineering ideal sources of single photons.

quant-ph↗

arXiv2022

High-speed detection of 1550 nm single photons with superconducting nanowire detectors

Superconducting nanowire single photon detectors are a key technology for quantum information and science due to their high efficiency, low timing jitter, and low dark counts. In this work, we present a detector for single 1550 nm photons with up to 78% detection efficiency, timing jitter below 50 ps FWHM, 158 counts/s dark count rate - as well as a world-leading maximum count rate of 1.5 giga-counts/s at 3 dB compression. The PEACOQ detector (Performance-Enhanced Array for Counting Optical Quanta) comprises a linear array of 32 straight superconducting niobium nitride nanowires which span the mode of an optical fiber. This design supports high count rates with minimal penalties for detection efficiency and timing jitter. We show how these trade-offs can be mitigated by implementing independent read-out for each nanowire and by using a temporal walk correction technique to reduce count-rate dependent timing jitter. These detectors make quantum communication practical on a 10 GHz clock.

quant-ph↗

arXiv2022

Time-walk and jitter correction in SNSPDs at high count rates

Superconducting nanowire single-photon detectors (SNSPDs) are a leading detector type for time correlated single photon counting, especially in the near-infrared. When operated at high count rates, SNSPDs exhibit increased timing jitter caused by internal device properties and features of the RF amplification chain. Variations in RF pulse height and shape lead to variations in the latency of timing measurements. To compensate for this, we demonstrate a calibration method that correlates delays in detection events with the time elapsed between pulses. The increase in jitter at high rates can be largely canceled in software by applying corrections derived from the calibration process. We demonstrate our method with a single-pixel tungsten silicide SNSPD and show it decreases high count rate jitter. The technique is especially effective at removing a long tail that appears in the instrument response function at high count rates. At a count rate of 11.4 MCounts/s we reduce the full width at one percent maximum level (FW1%M) by 45%. The method therefore enables certain quantum communication protocols that are rate-limited by the (FW1%M) metric to operate almost twice as fast. \c{opyright} 2022. All rights reserved.

quant-ph↗

arXiv2022

Picosecond Synchronization of Photon Pairs through a Fiber Link between Fermilab and Argonne National Laboratories

We demonstrate a three-node quantum network for C-band photon pairs using 2 pairs of 59 km of deployed fiber between Fermi and Argonne National Laboratories. The C-band pairs are directed to nodes using a standard telecommunication switch and synchronized to picosecond-scale timing resolution using a coexisting O- or L-band optical clock distribution system. We measure a reduction of coincidence-to-accidental ratio (CAR) of the C-band pairs from 51 $\pm$ 2 to 5.3 $\pm$ 0.4 due to Raman scattering of the O-band clock pulses. Despite this reduction, the CAR is nevertheless suitable for quantum networks.

quant-ph↗

arXiv2022

Picosecond synchronization system for quantum networks

The operation of long-distance quantum networks requires photons to be synchronized and must account for length variations of quantum channels. We demonstrate a 200 MHz clock-rate fiber optic-based quantum network using off-the-shelf components combined with custom-made electronics and telecommunication C-band photons. The network is backed by a scalable and fully automated synchronization system with ps-scale timing resolution. Synchronization of the photons is achieved by distributing O-band-wavelength laser pulses between network nodes. Specifically, we distribute photon pairs between three nodes, and measure a reduction of coincidence-to-accidental ratio from 77 to only 42 when the synchronization system is enabled, which permits high-fidelity qubit transmission. Our demonstration sheds light on the role of noise in quantum communication and represents a key step in realizing deployed co-existing classical-quantum networks.

quant-ph↗

arXiv2021

The thermally-coupled imager: A scalable readout architecture for superconducting nanowire single photon detectors

Although superconducting nanowire single-photon detectors (SNSPDs) are a promising technology for quantum optics, metrology, and astronomy, they currently lack a readout architecture that is scalable to the megapixel regime and beyond. In this work, we have designed and demonstrated such an architecture for SNSPDs, called the thermally-coupled imager (TCI). The TCI uses a combination of time-of-flight delay lines and thermal coupling to create a scalable architecture that can scale to large array sizes, allows neighboring detectors to operate independently, and requires only four microwave readout lines to operate no matter the size of the array. We give an overview of how the architecture functions, and demonstrate a proof-of-concept $32\times32$ imaging array. The array was able to image a free-space focused spot at 373 nm, count at 9.6 Mcps, and resolve photon location with greater than 99.83\% distinguishability.

cond-mat.supr-con↗

arXiv2021

Impedance-matched differential superconducting nanowire detectors

Superconducting nanowire single-photon detectors (SNSPDs) are the highest performing photon-counting technology in the near-infrared (NIR). Due to delay-line effects, large area SNSPDs typically trade-off timing resolution and detection efficiency. Here, we introduce a detector design based on transmission line engineering and differential readout for device-level signal conditioning, enabling a high system detection efficiency and a low detector jitter, simultaneously. To make our differential detectors compatible with single-ended time taggers, we also engineer analog differential-to-single-ended readout electronics, with minimal impact on the system timing resolution. Our niobium nitride differential SNSPDs achieve $47.3\,\% \pm 2.4\,\%$ system detection efficiency and sub-$10\,\mathrm{ps}$ system jitter at $775\,\mathrm{nm}$, while at $1550\,\mathrm{nm}$ they achieve $71.1\,\% \pm 3.7\,\%$ system detection efficiency and $13.1\,\mathrm{ps} \pm 0.4\,\mathrm{ps}$ system jitter. These detectors also achieve sub-100 ps timing response at one one-hundredth maximum level, $30.7\,\mathrm{ps} \pm 0.4\,\mathrm{ps}$ at $775\,\mathrm{nm}$ and $47.6\,\mathrm{ps} \pm 0.4\,\mathrm{ps}$ at $1550\,\mathrm{nm}$, enabling time-correlated single-photon counting with high dynamic range response functions. Furthermore, thanks to the differential impedance-matched design, our detectors exhibit delay-line imaging capabilities and photon-number resolution. The properties and high-performance metrics achieved by our system make it a versatile photon-detection solution for many scientific applications.

physics.app-ph↗

arXiv2020

Teleportation Systems Towards a Quantum Internet

Quantum teleportation is essential for many quantum information technologies including long-distance quantum networks. Using fiber-coupled devices, including state-of-the-art low-noise superconducting nanowire single photon detectors and off-the-shelf optics, we achieve quantum teleportation of time-bin qubits at the telecommunication wavelength of 1536.5 nm. We measure teleportation fidelities of >=90% that are consistent with an analytical model of our system, which includes realistic imperfections. To demonstrate the compatibility of our setup with deployed quantum networks, we teleport qubits over 22 km of single-mode fiber while transmitting qubits over an additional 22 km of fiber. Our systems, which are compatible with emerging solid-state quantum devices, provide a realistic foundation for a high-fidelity quantum internet with practical devices.

quant-ph↗

arXiv2020

Superconducting microwire detectors with single-photon sensitivity in the near-infrared

We report on the fabrication and characterization of single-photon-sensitive WSi superconducting detectors with wire widths from 1 μm to 3 μm. The devices achieve saturated internal detection efficiency at 1.55 μm wavelength and exhibit maximum count rates in excess of 10^5 s^-1. We also investigate the material properties of the silicon-rich WSi films used for these devices. We find that many devices with active lengths of several hundred microns exhibit critical currents in excess of 50% of the depairing current. A meandered detector with 2.0 μm wire width is demonstrated over a surface area of 362x362 μm^2, showcasing the material and device quality achieved.

physics.app-ph↗

arXiv2020

Development of Quantum InterConnects for Next-Generation Information Technologies

Just as classical information technology rests on a foundation built of interconnected information-processing systems, quantum information technology (QIT) must do the same. A critical component of such systems is the interconnect, a device or process that allows transfer of information between disparate physical media, for example, semiconductor electronics, individual atoms, light pulses in optical fiber, or microwave fields. While interconnects have been well engineered for decades in the realm of classical information technology, quantum interconnects (QuICs) present special challenges, as they must allow the transfer of fragile quantum states between different physical parts or degrees of freedom of the system. The diversity of QIT platforms (superconducting, atomic, solid-state color center, optical, etc.) that will form a quantum internet poses additional challenges. As quantum systems scale to larger size, the quantum interconnect bottleneck is imminent, and is emerging as a grand challenge for QIT. For these reasons, it is the position of the community represented by participants of the NSF workshop on Quantum Interconnects that accelerating QuIC research is crucial for sustained development of a national quantum science and technology program. Given the diversity of QIT platforms, materials used, applications, and infrastructure required, a convergent research program including partnership between academia, industry and national laboratories is required. This document is a summary from a U.S. National Science Foundation supported workshop held on 31 October - 1 November 2019 in Alexandria, VA. Attendees were charged to identify the scientific and community needs, opportunities, and significant challenges for quantum interconnects over the next 2-5 years.

quant-ph↗

arXiv2019

Intrinsically-limited timing jitter in molybdenum silicide superconducting nanowire single-photon detectors

Recent progress in the development of superconducting nanowire single-photon detectors (SNSPDs) has delivered excellent performances, and has had a great impact on a range of research fields. The timing jitter, which denotes the temporal resolution of the detection, is a crucial parameter for many applications. Despite extensive work since their apparition, the lowest jitter achievable with SNSPDs is still not clear, and the origin of the intrinsic limits is not fully understood. Understanding its intrinsic behaviour and limits is a mandatory step toward improvements. Here, we report our experimental study on the intrinsically-limited timing jitter in molybdenum silicide (MoSi) SNSPDs. We show that to reach intrinsic jitter, several detector properties such as the latching current and the kinetic inductance of the devices have to be understood. The dependence on the nanowire cross-section and the energy dependence of the intrinsic jitter are exhibited, and the origin of the limits are explicited. System timing jitter of 6.0 ps at 532 nm and 10.6 ps at 1550 nm photon wavelength have been obtained.

physics.ins-det↗

arXiv2018

Simple 2.5 GHz time-bin quantum key distribution

We present a 2.5 GHz quantum key distribution setup with the emphasis on a simple experimental realization. It features a three-state time-bin protocol based on a pulsed diode laser and a single intensity modulator. Implementing an efficient one-decoy scheme and finite-key analysis, we achieve record breaking secret key rates of 1.5 kbps over 200 km of standard optical fiber.

quant-ph↗