arXiv subjects

C. -C. Lai

Publications and source records attributed to C. -C. Lai.

4 recordsLinked to original sources

arXiv2026

Alpha Background in Multi-Grid Neutron Detectors

Alpha emission from actinide impurities in Al is a source of background counting rate in Multi-Grid type detectors of thermal neutrons. The alpha emission rates from samples of radio-purity Al and \mathrm{Al/B_{4}C} composite, used in grid construction, were measured on a large-area, low background spectrometer. Although the alpha emission rate from the composite was a factor \sim280 higher than radio-pure Al, \mathrm{25\:μm} Ni plating of the composite reduced the rate by a factor \sim1170. Background counting rates in two Multi-Grid prototypes were compared. They used identical configurations of \mathrm{B_{4}C}-coated, radio-pure Al normal blades for the grids, but the first employed radio-purity Al for the radial blades, while the second used Ni-plated \mathrm{Al/B_{4}C} on the radial blades. The background rate from the second prototype was around 20% of that from the first.

physics.ins-det↗

arXiv2025

Neutron Interaction Properties of Structural Materials for Multi-Grid Neutron Detectors

The T-REX neutron time-of-flight spectrometer at the European Spallation Source will use Multi-Grid Technology, which relies on thin B4C coatings on the Al blades of the grids to detect scattered thermal neutrons. Following a Monte Carlo study of internal shielding to suppress neutron multiple scattering in T-REX, the neutron transmission and scattering properties of 12 shielding-material samples have been measured at the ISIS spallation neutron source. Neutron transmission was measured on the EMMA beam line at wavelengths 0.5-4.7 A, using a 2D-position-sensitive, neutron GEM detector, while neutron scattering was measured for 6 of the samples at the Merlin spectrometer, at wavelengths 0.72, 1.28, 1.85 and 2.41 A. The present tests show that a B4C/Al composite material, plated with Ni to stop intrinsic alpha background, is an effective neutron absorber, suitable for incorporation in the Multi-Grid structures which detect the neutrons in inelastic neutron spectrometers .

physics.ins-det↗

arXiv2021

Time- and energy-resolved effects in the boron-10 based Multi-Grid and helium-3 based thermal neutron detectors

The boron-10 based Multi-Grid detector is being developed as an alternative to helium-3 based neutron detectors. At the European Spallation Source, the detector will be used for time-of-flight neutron spectroscopy at cold to thermal neutron energies. The objective of this work is to investigate fine time- and energy-resolved effects of the Multi-Grid detector, down to a few $μ$eV, while comparing it to the performance of a typical helium-3 tube. Furthermore, it is to characterize differences between the detector technologies in terms of internal scattering, as well as the time reconstruction of ~ $μ$s short neutron pulses. The data were taken at the Helmholtz Zentrum Berlin, where the Multi-Grid detector and a helium-3 tube were installed at the ESS test beamline, V20. Using a Fermi-chopper, the neutron beam of the reactor was chopped into a few tens of $μ$s wide pulses before reaching the detector, located a few tens of cm downstream. The data of the measurements show an agreement between the derived and calculated neutron detection efficiency curve. The data also provide fine details on the effect of internal scattering, and how it can be reduced. For the first time, the chopper resolution was comparable to the timing resolution of the Multi-Grid detector. This allowed a detailed study of time- and energy resolved effects, as well as a comparison with a typical helium-3 tube.

physics.ins-det↗

arXiv2020

u-RANIA: a neutron detector based on μ-RWELL technology

In the framework of the ATTRACT-uRANIA project, funded by the European Community, we are developing an innovative neutron imaging detector based on micro-Resistive WELL ($μ$ -RWELL) technology. The $μ$ -RWELL, based on the resistive detector concept, ensuring an efficient spark quenching mechanism, is a highly reliable device. It is composed by two main elements: a readout-PCB and a cathode. The amplification stage for this device is embedded in the readout board through a resistive layer realized by means of an industrial process with DLC (Diamond-Like Carbon). A thin layer of B$_4$C on the copper surface of the cathode allows the thermal neutrons detection through the release of $^7$Li and $α$ particles in the active volume. This technology has been developed to be an efficient and convenient alternative to the $^3$He shortage. The goal of the project is to prove the feasibility of such a novel neutron detector by developing and testing small planar prototypes with readout boards suitably segmented with strip or pad read out, equipped with existing electronics or readout in current mode. Preliminary results from the test with different prototypes, showing a good agreement with the simulation, will be presented together with construction details of the prototypes and the future steps of the project.

physics.ins-det↗