arXiv subjects

C. Scheuerlein

Publications and source records attributed to C. Scheuerlein.

5 recordsLinked to original sources

arXiv2017

Nb3Sn wire shape and cross sectional area inhomogeneity in Rutherford cables

During Rutherford cable production the wires are plastically deformed and their initially round shape is distorted. Using X-ray absorption tomography we have determined the 3D shape of an unreacted Nb3Sn 11 T dipole Rutherford cable, and of a reacted and impregnated Nb3Sn cable double stack. State-of-the-art image processing was applied to correct for tomographic artefacts caused by the large cable aspect ratio, for the segmentation of the individual wires and subelement bundles inside the wires, and for the calculation of the wire cross sectional area and shape variations. The 11 T dipole cable cross section oscillates by 2% with a frequency of 1.24 mm (1/80 of the transposition pitch length of the 40 wire cable). A comparatively stronger cross sectional area variation is observed in the individual wires at the thin edge of the keystoned cable where the wire aspect ratio is largest.

physics.acc-ph↗

arXiv2017

Thermomechanical Behavior of the HL-LHC 11 Tesla Nb3Sn Magnet Coil Constituents during Reaction Heat Treatment

The knowledge of the temperature induced changes of the superconductor volume, and of the thermo-mechanical behaviour of the different coil and tooling materials is required for predicting the coil geometry and the stress distribution in the coil after the Nb3Sn reaction heat treatment. In the present study we have measured the Young's and shear moduli of the HL-LHC 11 T Nb3Sn dipole magnet coil and reaction tool constituents during in situ heat cycles with the dynamic resonance method. The thermal expansion behaviours of the coil components and of a free standing Nb3Sn wire were compared based on dilation experiments.

cond-mat.mtrl-sci↗

arXiv2015

Performance Boost in Industrial Multifilamentary Nb3Sn Wires due to Radiation Induced Pinning Centers

We report non-Cu critical current densities of 4.09 * 10^9 A/m^2 at 12 T and 2.27 * 10^9 A/m^2 at 15 T obtained from transport measurements on a Ti-alloyed RRP Nb3Sn wire after irradiation to a fast neutron fluence of 8.9 * 10^21 m^-2. These values are to our knowledge unprecedented in multifilamentary Nb3Sn, and they correspond to a Jc enhancement of approximately 60% relative to the unirradiated state. Our magnetometry data obtained on short wire samples irradiated to fast neutron fluences of up to 2.5 * 10^22 m^-2 indicate the possibility of an even better performance, whereas earlier irradiation studies on bronze-processed Nb3Sn wires with a Sn content further from stoichiometry attested a decline of the critical current density at such high fluences. We show that radiation induced point-pinning centers rather than an increase of the upper critical field are responsible for this Jc enhancement, and argue that these results call for further research on pinning landscape engineering.

cond-mat.supr-con↗

arXiv2013

Effects of Neutron Irradiation on Pinning Force Scaling in State-of-the-Art Nb3Sn Wires

We present an extensive irradiation study involving five state-of-the-art Nb3Sn wires which were subjected to sequential neutron irradiation up to a fast neutron fluence of 1.6 * 10^22 m^-2 (E > 0.1 MeV). The volume pinning force of short wire samples was assessed in the temperature range from 4.2 to 15 K in applied fields of up to 7 T by means of SQUID magnetometry in the unirradiated state and after each irradiation step. Pinning force scaling computations revealed that the exponents in the pinning force function differ significantly from those expected for pure grain boundary pinning, and that fast neutron irradiation causes a substantial change in the functional dependence of the volume pinning force. A model is presented, which describes the pinning force function of irradiated wires using a two-component ansatz involving a point-pinning contribution stemming from radiation induced pinning centers. The dependence of this point-pinning contribution on fast neutron fluence appears to be a universal function for all examined wire types.

cond-mat.supr-con↗

arXiv2013

A transformative superconducting magnet technology for fields well above 30 T using isotropic round wire multifilament Bi2Sr2CaCu2O8-x conductor

We report here that magnetic fields of almost 34 T, far above the upper 24 T limit of Nb3Sn, can be generated using a multifilament round wire conductor made of the high temperature cuprate superconductor Bi2Sr2CaCu2O8-x (Bi-2212). A remarkable attribute of this Bi-2212 conductor is that it does not exhibit macroscopic texture and contains many high angle grain boundaries but nevertheless attains very high superconducting critical current densities Jc of 2500 A/mm2 at 20 T and 4.2 K. This Bi-2212 conductor does not possess the extreme texture that high Jc coated conductors of REBa2Cu3O7-x (REBCO) require, avoiding also its high aspect ratio, large superconducting anisotropy and the inherent sensitivity to defects of a single filament conductor. Bi-2212 wires can be wound or cabled into almost any type of superconducting magnet and will be especially valuable for very high field NMR magnets beyond the present 1 GHz proton resonance limit of Nb3Sn technology. This demonstration that grain boundary limits to high Jc can be practically overcome suggests the huge value of a renewed focus on grain boundary properties in non-ideal geometries, especially with the goal of translating the lessons of this Bi-2212 conductor into fabrication of multifilament round wire REBCO or Fe-based superconductors.

cond-mat.supr-con↗