arXiv subjects

Carlo Scarcia

Publications and source records attributed to Carlo Scarcia.

3 recordsLinked to original sources

arXiv2026

Technical Proposal for the Atom Interferometer CERN Experiment (AICE) Facility

We present the technical proposal for the Atom Interferometer CERN Experiment (AICE), a $\mathcal{O}(100)$ m vertical atom interferometer to be installed against the wall of the PX46 access shaft to the LHC. AICE is conceived as a versatile and flexible long-baseline atom-interferometry facility whose primary scientific goal is probing for bosonic ultralight dark matter (ULDM) in a mass range inaccessible to other experiments, with a secondary goal of pioneering the exploration of gravitational waves (GWs) with frequencies in the range ${\sim}$0.03-3 Hz as a pathfinder for future longer-baseline detectors. The initial configuration employs ultracold $^{87}$Sr atoms in a single-photon 698-nm interferometer with three shaft-based atom sources in a multi-source gradiometer geometry, supported by one surface reference source for laser stabilisation and diagnostics, to target scalar ULDM. Operation with $^{88}$Sr will give sensitivity to axion-like particles (ALPs), vector ULDM with $B-L$ couplings and violation of the principle of equivalence, while a $^{171}$Yb upgrade will improve the sensitivity to $B-L$ couplings and equivalence violations. Probing the Einstein equivalence principle (EP) and measuring $\alpha$ will proceed in parallel with the ULDM searches. A conceptual feasibility study and a detailed technical implementation study have established that PX46 is a uniquely mature and implementation-ready site, with no technical showstoppers. Completing site preparation works during LS3 would enable the subsequent installation and operation of AICE without impacting HL-LHC operations. The detector design builds on the VLBAI and MAGIS experiments and the AION-10 Technical Design Report, scaling the strontium gradiometer architecture to the $\sim$100 m baseline. AICE is endorsed by the TVLBAI Proto-Collaboration, comprising 57 institutions in 22 countries.

hep-ex↗

arXiv2025

Study of the UHV compatibility of selected ferritic stainless steels for application in vacuum systems of future gravitational wave detectors

Next-generation gravitational wave detectors (GWDs) such as the Cosmic Explorer and Einstein Telescope demand extensive ultra-high vacuum systems, making material cost and performance critical considerations. This study investigates the potential of ferritic stainless steel as a cost-effective alternative to the commonly used austenitic stainless steel for UHV components, focusing on the analysis of outgassing rates pre and post-bakeout at 80{\deg}C and 150{\deg}C for 48 hours. The tested ferritic stainless steels exhibit significantly lower hydrogen content than standard AISI 304L steel. After bakeout, the hydrogen outgassing rates - measured down to 10$^{-15}$ mbar l s$^{-1}$ cm$^{-2}$ - are three orders of magnitude lower than those of similarly conditioned austenitic stainless steels. These results highlight ferritic stainless steel as a promising, economical, and high-performance candidate for future GWDs vacuum systems.

astro-ph.IM↗

arXiv2024

Study of selected mild steels for application in vacuum systems of future gravitational wave detectors

Next-generation gravitational wave detectors (GWDs) like the Cosmic Explorer and Einstein Telescope require extensive vacuum tubing, necessitating cost-effective materials. This study explores the viability of mild steel as an alternative to austenitic stainless steel for UHV beampipes, focusing on outgassing rates and surface chemistry after low-temperature bakeouts. Mild steels exhibit significantly lower hydrogen outgassing rates, below 10$^{-14}$ mbar l s$^{-1}$ cm$^{-2}$ after bakeouts at 80{\deg}C for 48 hours. While water vapor is the primary residual gas after such low-temperature bakeouts, repeated treatments reduce its outgassing rate and modify surface conditions so that such benefit is preserved after at least six months of exposure to laboratory air. These findings position mild steel as an economical and efficient material for future GWD beampipes.

physics.acc-ph↗