Searcharxiv⌕ Search

arXiv subjects

Cecilia Granados-Miralles

Publications and source records attributed to Cecilia Granados-Miralles.

15 recordsLinked to original sources
arXiv2025

Unraveling structural and magnetic information during growth of nanocrystalline SrFe12O19

The hydrothermal synthesis of magnetic strontium hexaferrite (SrFe12O19) nanocrystallites was followed in situ using synchrotron powder X-ray diffraction. For all the studied temperatures, the formation of SrFe12O19 happened through an intermediate crystalline phase, identified as the so-called six-line ferrihydrite (FeOOH). The presence of FeOOH has been overlooked in previous studies on hydrothermally synthesized SrFe12O19, despite the phase having a non-trivial influence on the magnetic properties of the final material. The chemical synthesis was successfully reproduced ex situ in a custom-designed batch-type reactor that resembles the experimental conditions of the in situ setup, while allowing larger quantities of material to be produced. The agreement in phase composition between the two studies reveals comparability between both experimental setups. Hexagonal platelet morphology is confirmed for SrFe12O19 combining Rietveld refinements of powder X-ray diffraction (PXRD) data with transmission electron microscopy (TEM). Room temperature magnetization curves were measured on the nanopowders prepared ex situ. The magnetic properties are discussed in the context of the influence of phase composition and crystallite size.

cond-mat.mtrl-sci↗
arXiv2024

The Chemistry of Spinel Ferrite Nanoparticle Nucleation, Crystallization, and Growth

The nucleation, crystallization, and growth mechanisms of MnFe2O4, CoFe2O4, NiFe2O4, and ZnFe2O4 nanocrystallites prepared from coprecipitated transition metal (TM) hydroxide precursors treated at sub-, near-, and supercritical hydrothermal conditions have been studied by in situ X-ray total scattering (TS) with pair distribution function (PDF) analysis, and in situ synchrotron powder X-ray diffraction (PXRD) with Rietveld analysis. The in situ TS experiments were carried out on 0.6 M TM hydroxide precursors prepared from aqueous metal chloride solutions using 24.5% NH4OH as the precipitating base. The PDF analysis reveals equivalent nucleation processes for the four spinel ferrite compounds under the studied hydrothermal conditions, where the TMs form edge-sharing octahedrally coordinated hydroxide units (monomers/dimers and in some cases trimers) in the aqueous precursor, which upon hydrothermal treatment nucleate through linking by tetrahedrally coordinated TMs. The in situ PXRD experiments were carried out on 1.2 M TM hydroxide precursors prepared from aqueous metal nitrate solutions using 16 M NaOH as the precipitating base. The crystallization and growth of the nanocrystallites were found to progress via different processes depending on the specific TMs and synthesis temperatures. The PXRD data show that MnFe2O4 and CoFe2O4 nanocrystallites rapidly grow (typically <1 min) to equilibrium sizes of 20-25 nm and 10-12 nm, respectively, regardless of applied temperature in the 170-420 C range, indicating limited possibility of targeted size control. However, varying the reaction time (0-30 min) and temperature (150-400 C) allows different sizes to be obtained for NiFe2O4 (3-30 nm) and ZnFe2O4 (3-12 nm) nanocrystallites.

cond-mat.mtrl-sci↗
arXiv2023

Permanent Magnets Based on Hard Ferrite Ceramics

Permanent magnets are integral components in many of the modern technologies that are critical for the transition to a sustainable society. However, most of the high-performance (BHmax > 100 kJ/m3) permanent magnets that are currently employed contain rare earth elements (REE), which have long been classified as critical materials with a high supply risk and concerns regarding pollution in their mining. Therefore, suitable REE-lean/free magnets must be developed in order to ensure the sustainability of clean energy generation and electric mobility. The REE-free hexagonal ferrites (or hexaferrites) are the most used permanent magnets across all applications, with an 85 wt.% pie of the permanent magnet market. They are the dominant lower-grade option (BHmax < 25 kJ/m3) due to their relatively good hard magnetic properties, high Curie temperature (>700 K), low cost and good chemical stability. In recent years, the hexaferrites have also emerged as candidates for substituting REE-based permanent magnets in applications requiring intermediate magnetic performance (25-100 kJ/m3), due to considerable performance improvements achieved through chemical tuning, nanostructuring and compaction/sintering optimization. This chapter reviews the state-of-the-art sintering strategies being investigated with the aim of manufacturing hexaferrite magnets with optimized magnetic properties, identifying key challenges and highlighting the natural future steps to be followed.

cond-mat.mtrl-sci↗
arXiv2023

On the potential of hard ferrite ceramics for permanent magnet technology -- a review on sintering strategies

A plethora of modern technologies rely on permanent magnets for their operation, including many related to the transition towards a sustainable future, such as wind turbines or electric vehicles. Despite the overwhelming superiority of magnets based on rare-earth elements in terms of the magnetic performance, the harmful environmental impact of the mining of these raw materials, their uneven distribution on Earth and various political conflicts among countries leave no option but seeking for rare-earth-free alternatives. The family of the hexagonal ferrites or hexaferrites, and in particular the barium and strontium M-type ferrites (BaFe12O19 and SrFe12O19), are strong candidates for a partial rare-earth magnets substitution, and they are indeed successfully implemented in multiple applications. The manufacturing of hexaferrites into dense pieces (i.e. magnets) meeting the requirements of the specific application (e.g. magnetic and mechanical properties, shape) is not always straightforward, which has in many cases hampered the actual substitution at the industrial level. Here, past and on-going research on hexaferrites sintering is reviewed with a historical perspective, focusing on the challenges encountered and the solutions explored, and correlating the sintering approaches with the magnetic performance of the resulting ceramic magnet.

cond-mat.mtrl-sci↗
arXiv2023

Hexaferrite-based permanent magnets with upper magnetic properties by cold sintering process via a non-aqueous solvent

The incessant technological pursuit towards a more sustainable and green future depends strongly on permanent magnets. At present, their use is widespread, making it imperative to develop new processing methods that generate highly competitive magnetic properties reducing the fabrication temperatures and costs. Herein, a novel strategy for developing dense sintered magnets based on Sr-hexaferrites with upper functional characteristics is presented. An innovative cold sintering approach using glacial acetic acid as novelty, followed by a post-annealing at 1100 °C, achieves a densification of the ceramic magnets of 92% with respect to the theoretical density and allows controlling the particle growth. After the cold sintering process, a fraction of amorphous SrO is identified, in addition to a partial transformation to α-Fe2O3 as secondary crystalline phase. 46 wt% of SrFe12O19 remains, which is mostly recuperated after the post-thermal treatment. These findings do not significantly modify the final structure of ferrite magnets, neither at short- nor long-range order. The innovative process has a positive impact on the magnetic properties, yielding competitive ferrite magnets at lower sintering temperatures with an energy efficiency of at least 25%, which opens up a new horizon in the field of rare-earth free permanent magnets and new possibilities in other applications.

cond-mat.mtrl-sci↗
arXiv2023

Novel one-pot sol-gel synthesis route of Fe3C/few-layered graphene core/shell nanoparticles embedded in a carbon matrix

Fe3C/few-layered graphene core/shell nanoparticles embedded in a carbon matrix are synthesized by a novel two-step surfactant sol-gel strategy, where the processes of hydrolysis, polycondensation and drying take place in a one-pot. The present approach is based on the combined action of oleic acid and oleylamine, which act sterically on the precursor micelles when a densification temperature is performed in a reducing atmosphere. The structural and magnetic evolution of the formed compounds is investigated, ranging from iron oxides such as Fe3O4 and FeO, to the formation of pure Fe3C/C samples from 700 °C onwards. Interestingly, Fe3C nanoparticles with a size of ~20 nm crystallize immersed in the carbon matrix and the surrounding environment forms an oriented encapsulation built by few-layered graphene. The nanostructures show a saturation magnetization of ~43 emu/g and a moderate coercivity of ~500 Oe. Thereby, an innovative chemical route to produce single phase Fe3C nanoparticles is described, and an effective method of few-layered graphene passivation is proposed, yielding a product with a high magnetic response and high chemical stability against environmental corrosion.

cond-mat.mtrl-sci↗
arXiv2023

Dense strontium hexaferrite-based permanent magnet composites assisted by cold sintering process

The use of rare-earth-based permanent magnets is one of the critical points for the development of the current technology. On the one hand, industry of the rare-earths is highly polluting due to the negative environmental impact of their extraction and, on the other hand, the sector is potentially dependent on China. Therefore, investigation is required both in the development of rare-earth-free permanent magnets and in sintering processes that enable their greener fabrication with attractive magnetic properties at a more competitive price. This work presents the use of a cold sintering process (CSP) followed by a post-annealing at 1100 °C as a new way to sinter composite permanent magnets based on strontium ferrite (SFO). Composites that incorporate a percentage < 10% of an additional magnetic phase have been prepared and the morphological, structural and magnetic properties have been evaluated after each stage of the process. CSP induces a phase transformation of SFO in the composites, which is partially recovered by the post-thermal treatment improving the relative density to 92% and the magnetic response of the final magnets with a coercivity of up to 3.0 kOe. Control of the magnetic properties is possible through the composition and the grain size in the sintered magnets. These attractive results show the potential of the sintering approach as an alternative to develop modern rare-earth-free composite permanent magnets.

cond-mat.mtrl-sci↗
arXiv2023

CoSb3-based skutterudite nanocomposites prepared by cold sintering process with enhanced thermoelectric properties

We show here for the first time the use of a cold sintering process (CSP) to sinter CoSb3-based thermoelectric materials. CSP at 150 °C for 90 min under a uniaxial pressure of 750 MPa yields pieces with a relative density of 86 %, which is increased to around 92 % after a post-annealing at temperatures > 500 °C in Ar atmosphere. The reported CSP produces Te doped-CoSb3 nanocomposites with similar morphological and structural characteristics to the starting nanopowders obtained by ball milling in air atmosphere. The post-thermal treatment induces grain coalescence and grain growth, crystallite size growth as well as compositional changes in the nanocomposite, decreasing the amount of the main phase, CoSb3, and increasing the weight of secondary phase, CoSb2, up to a 30 wt% at 600 °C. Remarkably, the average valence for the Co, Sb and Te absorbing atoms is neither transformed by the sintering process nor by the subsequent heat treatment. The functional response of the sintered thermoelectric nanocomposites exhibits a maximum figure of merit of 0.12(3) at room temperature for the nanocomposites sintered by CSP with a subsequent post-annealing at 500 °C. This is mainly due to its low thermal conductivity in comparison with similar powders sintered by other approaches, and it is explained by the morphological and structural properties. These findings represent an attractive alternative for obtaining efficient thermoelectric skutterudites by a scalable and cost-effective route.

cond-mat.mtrl-sci↗
arXiv2023

Effect of organic solvent on the cold sintering processing of SrFe12O19 platelet-based permanent magnets

In this work we have investigated the effect of the solvent during the processing of SrFe12O19 platelet-based permanent magnets by cold sintering process (CSP) plus a post-thermal treatment. Several organic solvents: glacial acetic acid, oleic acid and oleylamine have been analyzed, optimizing the CSP temperatures at 190-270 °C, under pressures of 375-670 MPa and 6-50 wt% of solvent. Modifications in the morphological and structural properties are identified depending on the solvent, which impacts on the magnetic response. Independently of the solvent, the mechanical integrity of ferrite magnets obtained by CSP is improved by a post-annealing at 1100 °C for 2 h, resulting in relative densities around 92 % with an average grain size of 1 μm and a fraction of SrFe12O19 phase > 91 %. Hc > 2.1 kOe and MS of 73 emu/g are obtained in the final sintered ceramic magnets, exhibiting the highest HC value of 2.8 kOe for the magnet sintered using glacial acetic acid.

cond-mat.mtrl-sci↗
arXiv2023

A Platform for Addressing Individual Magnetite Islands Grown Epitaxially on Ru(0001) and Manipulating Their Magnetic Domains

We have grown high-quality magnetite micrometric islands on ruthenium stripes on sapphire through a combination of magnetron sputtering (Ru film), high-temperature molecular beam epitaxy (oxide islands), and optical lithography. The samples have been characterized by atomic force microscopy, Raman spectroscopy, X-ray absorption and magnetic circular dichroism in a photoemission microscope. The magnetic domains on the magnetite islands can be modified by the application of current pulses through the Ru stripes in combination with magnetic fields. The modification of the magnetic domains is explained by the Oersted field generated by the electrical current flowing through the stripes underneath the magnetite nanostructures. The fabrication method is applicable to a wide variety of rock salt and spinel oxides.

cond-mat.mtrl-sci↗
arXiv2023

Approaching Ferrite-Based Exchange-Coupled Nanocomposites as Permanent Magnets

During the past decade, CoFe2O4 (hard)/Co-Fe alloy (soft) magnetic nanocomposites have been routinely prepared by partial reduction of CoFe2O4 nanoparticles. Monoxide (i.e., FeO or CoO) has often been detected as a byproduct of the reduction, although it remains unclear whether the formation of this phase occurs during the reduction itself or at a later stage. Here, a novel reaction cell was designed to monitor the reduction in situ using synchrotron powder X-ray diffraction (PXRD). Sequential Rietveld refinements of the in situ data yielded time-resolved information on the sample composition and confirmed that the monoxide is generated as an intermediate phase. The macroscopic magnetic properties of samples at different reduction stages were measured by means of vibrating sample magnetometry (VSM), revealing a magnetic softening with increasing soft phase content, which was too pronounced to be exclusively explained by the introduction of soft material in the system. The elemental compositions of the constituent phases were obtained from joint Rietveld refinements of ex situ high-resolution PXRD and neutron powder diffraction (NPD) data. It was found that the alloy has a tendency to emerge in a Co-rich form, inducing a Co deficiency on the remaining spinel phase, which can explain the early softening of the magnetic material.

cond-mat.mtrl-sci↗
arXiv2023

Tuning the Néel temperature in an antiferromagnet: the case of NixCo1-xO microstructures

We show that it is possible to tune the Néel temperature of nickel(II)-cobalt(II) oxide films by changing the Ni to Co ratio. We grow single crystalline micrometric triangular islands with tens of nanometers thickness on a Ru(0001) substrate using high temperature oxygen-assisted molecular beam epitaxy. Composition is controlled by adjusting the deposition rates of Co and Ni. The morphology, shape, crystal structure and composition are determined by low-energy electron microscopy and diffraction, and synchrotron-based x-ray absorption spectromicroscopy. The antiferromagnetic order is observed by x-ray magnetic linear dichroism. Antiferromagnetic domains up to micrometer width are observed.

cond-mat.mtrl-sci↗
arXiv2023

Expanding the tunability and applicability of exchange-coupled/decoupled magnetic nanocomposites

CoFe2O4/Co-Fe magnetic composites are usually prepared through partial reduction of CoFe2O4, which often yields monoxides (i.e., FeO, CoO) as secondary phases. Since these compounds are paramagnetic at ambient conditions, the presence of a small amount of monoxide is generally downplayed in the literature, and the possible effects on the magnetic properties are simply ignored. However, the present study shows that even a low concentration of monoxide results in decoupling of the soft and hard magnetic phases, which inevitably leads to a deterioration of the magnetic properties. Additionally, it is confirmed that a partial reduction of CoFe2O4 is a suitable method to produce CoFe2O4/Co-Fe nanocomposites, provided that the treatment is well controlled with respect to duration, temperature and flow of reductant. A monoxide-free nanocomposite was produced and its magnetic properties evaluated both at room and low temperature. Our model system exemplifies the potential of exchange-coupling (and decoupling) as a tool to tune the magnetic properties of a material within a relatively wide range of values, thus widening its spectrum of potential applications.

cond-mat.mtrl-sci↗
arXiv2023

Remanence Increase in SrFe$_{12}$O$_{19}$/Fe Exchange-Decoupled Hard-Soft Composite Magnets Owing to Dipolar Interactions

In the search for improved permanent magnets, fueled by the geostrategic and environmental issues associated with rare-earth-based magnets, magnetically hard (high anisotropy)-soft (high magnetization) composite magnets hold promise as alternative magnets that could replace modern permanent magnets, such as rare-earth-based and ceramic magnets, in certain applications. However, so far, the magnetic properties reported for hard-soft composites have been underwhelming. Here, an attempt to further understand the correlation between magnetic and microstructural properties in strontium ferrite-based composites, hard SrFe$_{12}$O$_{19}$ (SFO) ceramics with different contents of Fe particles as soft phase, both in powder and in dense injection molded magnets, is presented. In addition, the influence of soft phase particle dimension, in the nano- and micron-sized regimes, on these properties is studied. While Fe and SFO are not exchange-coupled in our magnets, a remanence that is higher than expected is measured. In fact, in composite injection molded anisotropic (magnetically oriented) magnets, remanence is improved by 2.4% with respect to a pure ferrite identical magnet. The analysis of the experimental results in combination with micromagnetic simulations allows us to establish that the type of interaction between hard and soft phases is of a dipolar nature, and is responsible for the alignment of a fraction of the soft spins with the magnetization of the hard. The mechanism unraveled in this work has implications for the development of novel hard-soft permanent magnets.

cond-mat.mtrl-sci↗
arXiv2022

Size effects in the Verwey transition of nanometer-thick micron-wide magnetite crystals

We have monitored the Verwey transition in micrometer-wide, nanometer-thick magnetite islands on epitaxial Ru films on Al2O3(0001) using Raman spectroscopy. The islands have been grown by high-temperature oxygen-assisted molecular beam epitaxy. Below 100 K and for thicknesses above 20 nm the Raman spectra correspond to those observed in bulk crystals and high quality thin films for the sub-Verwey magnetite structure. At room temperature the width of the cubic phase modes is similar to the best reported in bulk crystals, indicating a similar level of electron-phonon interaction. The evolution of the Raman spectra upon cooling suggests that for islands thicker than 20 nm, structural changes appear first at temperatures starting at 150 K and the Verwey transition itself takes place at around 115 K. However, islands thinner than 20 nm show a very different Raman spectra indicating that while a transition takes place, the charge order of the ultrathin islands differs markedly from their thicker counterparts

cond-mat.mes-hall↗