arXiv subjects

Cheuk Wing Edmond Lam

Publications and source records attributed to Cheuk Wing Edmond Lam.

6 recordsLinked to original sources

arXiv2025

Non-coalescence and in-plane momentum generation in sessile droplet clusters

Intuitively, droplets in proximity merge when brought into contact. However, under certain conditions, they may not coalesce due to the entrapment of an interstitial gas film. Non-coalescence between water droplets has so far been observed during collisions of droplets moving with relative centroidal velocity, or in the presence of specific enabling effects such as high intervening gas pressures, surfactants, or large droplet sizes (diameter $\gtrsim 1~\mathrm{mm}$). Here, we report non-coalescence between water droplets over a much wider range of droplet diameters, from millimeters to as small as 100 microns, without the need for any of the above factors. Such non-coalescence occurs in sessile droplet clusters on water-repellent surfaces. When any two droplets in a cluster coalesce, the evolving interface of the coalescing droplets comes in apparent contact with other neighbouring droplets in the cluster, but does not necessarily trigger further coalescence. In fact, such apparent contact can manifest as a bouncing interaction, and depending on the initial geometric arrangement of droplets, it can result in significant lateral momentum generation, consequently leading to spontaneous in-plane self-propulsion of the participating droplets. The energy conversion efficiency of this process reaches as high as 9\% for closely packed clusters of three sessile droplets and increases further with an increase in the number of participating droplets. The resulting self-propulsion of such small droplets reveals a new pathway for passive droplet removal and surface renewal during dropwise condensation on superhydrophobic surfaces, critical in multiple applications.

physics.flu-dyn↗

arXiv2023

Durable, ultrathin, and antifouling polymer brush coating for efficient condensation heat transfer

Heat exchangers are made of metals because of their high heat conductivity and mechanical stability. Metal surfaces are inherently hydrophilic, leading to inefficient filmwise condensation. It is still a challenge to coat these metal surfaces with a durable, robust and thin hydrophobic layer, which is required for efficient dropwise condensation. Here, we report the non-structured and ultrathin (~6 nm) polydimethylsiloxane (PDMS) brushes on copper that sustain high-performing dropwise condensation in high supersaturation. Due to the flexible hydrophobic siloxane polymer chains, the coating has low resistance to drop sliding and excellent chemical stability. The PDMS brushes can sustain dropwise condensation for up to ~8 h during exposure to 111 °C saturated steam flowing at 3 m/s, with a 5-7 times higher heat transfer coefficient compared to filmwise condensation. The surface is self-cleaning and can reduce bacterial attachment by 99%. This low-cost, facile, fluorine-free, and scalable method is suitable for a great variety of condensation heat transfer applications.

cond-mat.mtrl-sci↗

arXiv2023

Condensate droplet roaming on nanostructured superhydrophobic surfaces

Jumping of coalescing condensate droplets from superhydrophobic surfaces is an interesting phenomenon which yields marked heat transfer enhancement over the more explored gravity-driven droplet removal mode in surface condensation, a phase change process of central interest to applications ranging from energy to water harvesting. However, when condensate microdroplets coalesce, they can also spontaneously propel themselves omnidirectionally on the surface independent of gravity and grow by feeding from droplets they sweep along the way. Here we observe and explain the physics behind this phenomenon of roaming of coalescing condensate microdroplets on solely nanostructured superhydrophobic surfaces, where the microdroplets are orders of magnitude larger than the underlaying surface nanotexture. We quantify and show that it is the inherent asymmetries in droplet adhesion during condensation, arising from the stochastic nature of nucleation within the nanostructures, that generates the tangential momentum driving the roaming motion. Subsequent dewetting during this conversion initiates a vivid roaming and successive coalescence process, preventing condensate flooding of the surface, and enhancing surface renewal. Finally, we show that the more efficient conversion process of roaming from excess surface energy to kinetic energy results in significantly improved heat transfer efficiency over condensate droplet jumping, the mechanism currently understood as maximum.

physics.flu-dyn↗

arXiv2021

Enhancing condensation on soft substrates through bulk lubricant infusion

Soft substrates such as polydimethylsiloxane (PDMS) enhance droplet nucleation during the condensation of water vapour, because their deformability inherently reduces the energetic threshold for heterogeneous nucleation relative to rigid substrates. However, this enhanced droplet nucleation is counteracted later in the condensation cycle, when the viscoelastic dissipation inhibits condensate droplet shedding from the substrate. Here, we show that bulk lubricant infusion in the soft substrate is a potential pathway for overcoming this limitation. We demonstrate that even 5% bulk lubricant infusion in PDMS reduces viscoelastic dissipation in the substrate by more than 30 times and more than doubles the droplet nucleation density. We correlate the droplet nucleation and growth rate with the material properties controlled by design, i.e. the fraction and composition of uncrosslinked chains, shear modulus, and viscoelastic dissipation. Through in-situ, microscale condensation on the substrates, we show that the increase in nucleation density and reduction in pre-coalescence droplet growth rate is insensitive to the percentage of lubricant in PDMS. Our results indicate the presence of a lubricant layer on the substrate surface that cloaks the growing condensate droplets. We visualize the cloaking effect and show that lubricant infusion in PDMS significantly increases the rate of cloaking compared to PDMS without any lubricant infusion. Finally, we show that the overall enhanced condensation due to bulk lubricant infusion in PDMS leads to more than 40% increase in dewing on the substrate.

cond-mat.soft↗

arXiv2021

Ultra-Thin Lubricant-Infused Vertical Graphene Nanoscaffolds for High-Performance Dropwise Condensation

Lubricant-infused surfaces (LIS) are highly efficient in repelling water and constitute a very promising family of materials for condensation processes occurring in a broad range of energy applications. However, the performance of LIS in such processes is limited by the inherent thermal resistance imposed by the thickness of the lubricant and supporting surface structure, as well as by the gradual depletion of the lubricant over time. Here we present a remarkable, ultra-thin (~70 nm) and conductive LIS architecture, obtained by infusing lubricant into a vertically grown graphene nanoscaffold on copper. The ultra-thin nature of the scaffold, combined with the high in-plane thermal conductivity of graphene, drastically minimize earlier limitations, effectively doubling the heat transfer performance compared to a state-of-the-art CuO LIS surface. We show that the effect of the thermal resistance to the heat transfer performance of a LIS surface, although often overlooked, can be so detrimental that a simple nanostructured CuO surface can outperform a CuO LIS surface, despite film condensation on the former. The present vertical graphene LIS is also found to be resistant to lubricant depletion, maintaining stable dropwise condensation for at least ~7 hours with no significant change of advancing contact angle and contact angle hysteresis. The lubricant consumed by the vertical graphene LIS is 52.6% less than the existing state-of-the-art CuO LIS, making also the fabrication process more economical.

physics.app-ph↗

arXiv2020

Sprayable Thin and Robust Carbon Nanofiber Composite Coating for Extreme Jumping Dropwise Condensation Performance

Condensation of water on metallic surfaces is critical for multiple energy conversion processes. Enhancement in condensation heat transfer efficiency often requires surface texturing and hydrophobicity, usually achieved through coatings, to maintain dropwise condensation. However, such surface treatments face conflicting challenges of minimal coating thermal resistance, enhanced coating durability and scalable fabrication. Here we present a thin (~ 2 μm) polytetrafluoroethylene - carbon nanofiber nanocomposite coating which meets these challenges and sustains coalescence-induced jumping droplet condensation for extended periods under highly demanding condensation conditions. Coating durability is achieved through improved substrate adhesion by depositing a sub-micron thick aluminum primer layer. Carbon nanofibers in a polytetrafluoroethylene matrix increase coating thermal conductivity and promote spontaneous surface nano-texturing to achieve superhydrophobicity for condensate microdroplets. The coating material can be deposited through direct spraying, ensuring economical scalability and versatility for a wide range of substrates. We know of no other coating for metallic surfaces that is able to sustain jumping dropwise condensation under shear of steam at 111 degC flowing at ~ 3 m s-1 over the surface for 10 hours and dropwise condensation for an additional 50 hours. Up to ~ 900% improvement in condensation heat transfer coefficient is achieved compared to conventional filmwise condensation.

cond-mat.mtrl-sci↗