arXiv subjects

Christopher Harbord

Publications and source records attributed to Christopher Harbord.

3 recordsLinked to original sources

arXiv2024

Microstructural evolution of Carrara marble during semi-brittle deformation

Fifteen marble samples were subjected to semi-brittle deformation through triaxial compression experiments, reaching axial strains of 0.5%, 1.0%, 2.0%, 4.0%, or 7.5% at temperatures of 20C, 200C, or 350C, under a confining pressure of 400 MPa. Deformation twins, lattice curvature, and intragranular microfractures in the samples were quantitatively characterised using forescattered electron images and electron backscatter diffraction. Microstructural analyses revealed that twins accommodate most of the shortening during the first 2% strain, whereas lattice curvature associated with geometrically necessary dislocations predominantly develops in the later stages. Intragranular fracture intensity exhibits an almost linear correlation with strain during the first 2% strain but increases more slowly thereafter. The mechanical data indicate a strong temperature dependence of yield stress, consistent with the temperature dependence of the critical resolved shear stress for dislocation glide. The subsequent strain hardening is likely caused by progressively increasing intensity of interactions among dislocations and between dislocations and twin boundaries. Based on the microstructural data and interpreted hardening mechanisms, we propose a phenomenological model, with microstructural state variables, for semi-brittle deformation at our experimental conditions as a step towards development of a microphysical constitutive model of semi-brittle deformation.

physics.geo-ph↗

arXiv2023

Grain-size effects during semi-brittle flow of calcite rocks

We study the role of grain size in the rheological behaviour of calcite aggregates in the semi-brittle regime. We conduct triaxial deformation tests on three rocks, Solnhofen limestone, Carrara marble and Wombeyan marble, with average grain sizes of 5-10 $\mu$m, 200 $\mu$m and 2 mm, respectively, at pressures in the range 200-800 MPa and temperatures in the range 20-400 $^\circ$C. At all conditions, both strength and hardening rate increase with decreasing grain size. Flow stress scales with the inverse of grain size to a power between 1/3 and 2/3. Hardening rate decreases linearly with the logarithm of grain size. In-situ ultrasonic monitoring reveals that P-wave speed tends to decrease with increasing strain, and that this decrease is more marked at room temperature than at 200 and 400 $^\circ$C. The decrease in wave speed is consistent with microcracking, which is more prevalent at low temperature and low pressure. Microstructural observations reveal high twin densities in all deformed samples. Twin density increases with stress, consistent with previous datasets. Spatial distributions of intragranular misorientation indicate that twins are sometimes obstacles to dislocation motion, but this effect is not ubiquitous. Computed slip-transfer statistics indicate that that twins are typically weaker barriers to dislocation glide than grain boundaries, so that their effect on dislocation accumulation and hardening rates is likely smaller than the effect of grain size. Indeed, our data reveal that grain size exerts a first-order control on flow stress and hardening in calcite, whereas twinning may only have a secondary impact on these behaviours.

physics.geo-ph↗

arXiv2022

A high pressure, high temperature gas medium apparatus to measure acoustic velocities during deformation of rock

A new set-up to measure acoustic wave velocities through deforming rock samples at high pressures (up to 1000 MPa), temperatures (up to 700$^\circ$C) and differential stress (up to 1500 MPa) has been developed in a recently refurbished gas medium triaxial deformation apparatus. The conditions span a wide range of geological environments, and allow us to accurately measure differential stress and strains at conditions which are typically only accessible in solid medium apparatus. Calibrations of our newly constructed internal furnace up to 1000 MPa confining pressure and temperatures of up to 400$^\circ$C demonstrate that the hot zone is displaced downwards with increasing confining pressure, resulting in temperature gradients that are minimised by adequately adjusting the sample position. Ultrasonic velocity measurements are conducted in the direction of compression by the pulse-transmission method. Arrival times are corrected for delays resulting from the geometry of the sample assembly and high-precision relative measurements are obtained by cross-correlation. Delays for waves reflected at the interface between the loading piston and sample are nearly linearly dependent on differential applied load due to the load dependence of interface stiffness. Measurements of such delays can be used to infer sample load internally. We illustrate the working of the apparatus by conducting experiments on limestone at 200 MPa confining pressure and room temperature and 400$^\circ$C. Ultrasonic data clearly show that deformation is dominated by microcracking at low temperature and by intracrystalline plasticity at high temperature.

physics.geo-ph↗