Searcharxiv⌕ Search

arXiv subjects

Clara J. Saraceno

Publications and source records attributed to Clara J. Saraceno.

33 records · Page 2Linked to original sources

High-power intracavity single-cycle THz pulse generation using thin lithium niobate

Ultrafast laser driven, single-cycle THz pulsed sources hold immense potential for scientific and industrial applications; however, their limited average power hinders their widespread application. In particular, applications where high repetition rates in the multi-MHz region and beyond are required are more severely affected, due to the lower pulse energies available for frequency conversion. In this respect, resonant enhancement both in passive and active resonators is a well-known technique for boosting the efficiency of nonlinear frequency conversion; however, this route has remained poorly explored for the generation of broadband THz pulses due to the inadequacy of typically employed nonlinear crystals. Here, we demonstrate that thin lithium niobate crystals used intracavity of multimode diode-pumped mode-locked thin-disk lasers are a promising platform to circumvent these difficulties. Using a 50-μm thin lithium niobate plate intracavity of a compact high-power mode-locked thin-disk laser, we generate milliwatt-level broadband THz pulses with a spectrum extending up to 3 THz at 44.8 MHz repetition rate, driven by 264 W of intracavity average power. This approach opens the door to efficient high-power single-cycle THz generation using affordable nonlinear crystals at very high repetition rates, scalable to kilowatt-level driving power with low cost and complexity.

physics.optics↗

Towards Intense Ultra-Broadband High Repetition Rate Terahertz Sources Based on Organic Crystals [Invited]

Increasing the average power of broadband, few-cycle terahertz (THz) sources is currently a topic of intense investigation, fueled by recent immense progress in high average power femtosecond laser driving sources at 1030 nm. However, many crucial applications would benefit not only from an increase in average power, but also from ultra-broad bandwidth, while maintaining high dynamic range at these frequencies. This calls for the challenging combination of high repetition rates and high average power simultaneously. Here, we discuss the recent progress in the promising approach enabled by organic crystals for THz-generation. Specifically, this review article discusses advances with the most commonly used organic crystals BNA, DAST, DSTMS, OH1 and HMQ-TMS. We place special emphasis on nonlinear and thermal properties and discuss future directions for this field.

physics.optics↗

GHz repetition rate, sub-100-fs Ho:CALGO laser at 2.1 um with watt-level average power

We report on a GHz fundamental repetition rate Kerr-lens mode-locked Ho:CALGO laser emitting at 2.1 um. The laser employs a ring-cavity to increase the fundamental repetition rate to 1.179 GHz and can be made to oscillate in both directions stably with nearly identical performance: for counterclockwise oscillation, it generates 93-fs pulses at 1.68 W of average power, whereas 92 fs and 1.69 W were measured for clockwise operation. Our current results represent the highest average power from a 2-um GHz oscillator and the first sub-100-fs pulse duration from a Ho-based oscillator.

physics.optics↗

Temperature-Dependent THz Properties and Emission of Organic Crystal BNA

As high-average power ultrafast lasers become increasingly available for nonlinear conversion, the temperature dependence of the material properties of nonlinear crystals becomes increasingly relevant. Here, we present temperature-dependent THz complex refractive index measurements of the organic crystal BNA over a wide range of temperatures from 300 K down to 80 K for THz frequencies up to 4 THz for the first time. Our measurements show that whereas the temperature-dependent refractive index has only minor deviation from room temperature values, the temperature-dependent absorption coefficient decreases at low temperature. We additionally compare these measurements with conversion efficiency and spectra observed during THz generation experiments in the same temperature range and using the same crystal, using an ultrafast Yb-laser for excitation. Surprisingly, the damage threshold of the material does not improve significantly upon cooling, pointing to a nonlinear absorption mechanism being responsible for damage. However, we observe a significant increase in THz yield at lower temperatures, which is most likely due to the reduced THz absorption. These findings will be useful for future designs of high average power pumped organic-crystal based THz-TDS systems.

physics.optics↗

Photoconductive receivers at 1030 nm for high average power pulsed THz detection

In the last few years, many advances have been made in the demonstration of high-average power pulsed THz sources; however, little effort has been made to study compatible sensitive field-resolved detectors. Here, we investigate ErAs:InAlGaAs photoconductive receivers optimized for a probe wavelength of 1030 nm and thus suitable for the new class of high-power ultrafast Ytterbium-based laser sources for THz generation and detection. The performance of the receiver is tested with a few-cycle THz source with high average power up to 20 mW and the dynamic range and saturation behavior of the receiver is thoroughly characterized. Under optimized settings, a dynamic range of more than 115 dB is reached in a 120 s measurement time with 20 mW of THz average power, which is among the highest reported values to date. By reviewing the state-of-the art in TDS measurement and post-processing technology, we identify current limitations and guidelines for further increasing the dynamic range towards 150 dB in short measurement times using high average power THz systems.

physics.optics↗

Low-noise, 2-W average power, 112-fs Kerr-lens mode-locked Ho:CALGO laser at 2.1 um

We report on an in-band pumped soft-aperture Kerr-lens mode-locked Ho:CALGO bulk laser at 2.1 um, generating 2 W of average power with 112 fs pulses at 91-MHz repetition rate. To the best of our knowledge, this is the highest average power from a 100-fs class mode-locked laser based on a Tm3+ or Ho3+ doped bulk material. We show that the laser has excellent noise properties with an integrated relative intensity noise of 0.02% and a timing jitter of 950 fs (RMS phase noise 0.543 mrad) in the integration interval from 10 Hz to 10 MHz. The demonstrated combination of high average power, short pulses, and low-noise make this an outstanding laser source for spectroscopy and many other applications at 2.1 um.

physics.optics↗

Spectral broadening of 2 mJ femtosecond pulses in a compact air-filled convex-concave multi-pass cell

Multi-pass cell (MPC) based temporal pulse compressors have emerged in the last years as a powerful and versatile solution to the intrinsic issue of long pulses from Yb-based high-power ultrafast lasers. However, the spectral broadening of high-energy (typically more than 100 uJ) pulses has only been realized in complex setups, i.e., in large and costly, pressure-controlled vacuum chambers to avoid strong focusing, ionization, and damage on the mirrors. Here, we present spectral broadening of 2 mJ pulses in a simple and compact (60 cm long) multi-pass cell operated in ambient air. Instead of the traditional Herriott cell with concave-concave (CC/CC) mirrors, we use a convex-concave (CX/CC) design, where the beam stays large at all times allowing both to minimize damage and operate in ambient air. We demonstrate spectral broadening of 2.1 mJ pulses at 100 kHz repetition rate (200 W of average power) from 2.1 nm (pulse duration of 670 fs) to a spectral bandwidth of 24.5 nm, supporting 133 fs pulses with 96% transmission efficiency. We show the compressibility of these pulses down to 134 fs, and verify that the spectral homogeneity of the beam is similar to previously reported CC/CC designs. To the best of our knowledge, this is the first report of a CX/CC MPC compressor, operated at high pulse energies in air. Because of its simplicity, small footprint and low cost, we believe this demonstration will have significant impact in the ultrafast laser community.

physics.optics↗

Broadband THz-TDS with 5.6 mW average power at 540 kHz using organic crystal BNA

We demonstrate efficient optical rectification in the organic crystal BNA (N-benzyl-2-methyl-4-nitroaniline), driven by a temporally compressed, commercially available industrial Yb-laser system operating at 540 kHz repetition rate. Our THz source reaches 5.6 mW of THz average power driven by 4.7 W, 45 fs pulses and the resulting THz-TDS combines a very broad bandwidth of 7.5 THz and a high dynamic range of 75 dB (in a measurement time of 70 s). The conversion efficiency at maximum THz power is 0.12%. To the best of our knowledge, this is the highest THz power so far demonstrated with BNA, achieved at a high repetition rate, and enabling to demonstrate a unique combination of bandwidth and dynamic range for THz-spectroscopy applications.

physics.optics↗

8.7-W average power, in-band pumped femtosecond Ho:CALGO laser at 2.1 um

We report on an in-band pumped SESAM mode-locked Ho:CALGO bulk laser with a record-high average power of 8.7 W and an optical-to-optical efficiency of 38.2% at a central wavelength of 2.1 um. At this power level, the bulk laser generates pulses with a duration of 369 fs at 84.4-MHz repetition rate, corresponding to a pulse energy of 103 nJ and a peak power of 246 kW. To the best of our knowledge, this is the highest average power and pulse energy directly generated from a mode-locked bulk laser in the 2-3 um wavelength region. Our current results indicate that Ho:CALGO is a competitive candidate for average power scaling of 2 um femtosecond lasers.

physics.optics↗

50-W average power Ho:YAG SESAM-modelocked thin-disk oscillator at 2.1 um

Ultrafast laser systems operating with high-average power in the wavelength range from 1.9 um to 3 um are of interest for a wide range of applications for example in spectroscopy, material processing and as drivers for secondary sources in the XUV spectral region. In this area, laser systems based on holmium-doped gain materials directly emitting at 2.1 um have made significant progress over the past years, however so far only very few results were demonstrated in power-scalable high-power laser geometries. In particular, the thin-disk geometry is promising for directly modelocked oscillators with high average power levels that are comparable to amplifier systems at MHz repetition rate. In this paper, we demonstrate Semiconductor Saturable Absorber Mirror (SESAM) modelocked Ho:YAG thin-disk lasers (TDLs) emitting at 2.1 um wavelength with record-holding performance levels. In our highest average power configuration, we reach 50 W of average power, with 1.13 ps pulses, 2.11 uJ of pulse energy and ~1.9 MW of peak power. To the best of our knowledge, this represents the highest average power, as well as the highest output pulse energy so far demonstrated from a modelocked laser in the 2 um wavelength region. This record performance level was enabled by the recent development of high-power GaSb-based SESAMs with low loss, adapted for high intracavity power and pulse energy. We also explore the limitations in terms of reaching shorter pulse durations at high power with this gain material in the disk geometry and using SESAM modelocking, and present first steps in this direction, with the demonstration of 30 W of output power, with 692 fs pulses in another laser configuration.

physics.optics↗

Average power scaling of THz spintronic emitters in reflection geometry

Metallic spintronic THz emitters have become well-established for offering ultra-broadband, gap-less THz emission in a variety of excitation regimes, in combination with reliable fabrication and excellent scalability. However, so far, their potential for high-average-power excitation to reach strong THz fields at high repetition rates has not been thoroughly investigated. In this article, we explore the power scaling behavior of tri-layer spintronic emitters using an Yb-fiber excitation source, delivering an average power of 18.5 W at 400 kHz repetition rate, temporally compressed to a pulse duration of 27 fs. We confirm that the reflection geometry with back-side cooling is ideally suited for these emitters in the high-average-power excitation regime. In order to understand limiting mechanisms, we disentangle the effects on THz power generation by average power and pulse energy, by varying the repetition rate of the laser. Our results show that the conversion efficiency remains mostly dependent on the incident fluence in this high-average-power, high-repetition-rate excitation regime if the emitters are efficiently cooled. Using these findings, we optimize the conversion efficiency to reach 5e-6 at highest excitation powers in the back-cooled reflection geometry. Our findings provide guidelines for scaling the power of THz radiation emitted by spintronic emitters to the mW-level by using state-of-the-art femtosecond sources with multi-hundred-Watt average power to reach ultra-broadband, strong-field THz sources with high repetition rate.

physics.optics↗

Moving towards high-power thin-disk lasers in the 2-μm wavelength range

Thin-disk lasers (TDLs) have made spectacular progress in the last decades both in continuous-wave and ultrafast operation. Nowadays, single thin-disk oscillators with > 16 kW of continuous-wave (CW)-power have been demonstrated and ultrafast amplifiers have largely surpassed the kilowatt milestone with pulse energies in the multi-100 mJ range. This amazing development has been demonstrated in the 1-μm wavelength range, using Yb-doped materials and supported by industrially available components. Motivated by both strong scientific and industrial applications, interest in expanding this performance to longer wavelength regions continues to increase. In particular, TDLs emitting directly in the short-wave mid-infrared (SW-MIR) region (2-3 μm) are especially sought after, and although many early studies have been reported, most remained in the proof-of-principle stage and the potential for multi-100-W operation remained undemonstrated. Here, we report on our recent results of a single fundamental-mode CW Ho:YAG thin-disk oscillator with >100 W of power, surpassing previous single-mode TDLs by a factor of >4, and marking a first milestone in the development of high-power SW-MIR TDLs. In optimized conditions, our laser system emitting at » 2.1 μm reaches an output power of 112 W with 54.6-% optical-to-optical efficiency and an M2 = 1.1. This system is ideally suited for future direct modelocking at the 100 W level, as well as for ultrafast amplification. We start the discussion with a review of the state-of-the-art of TDLs emitting directly in the vicinity of 2 μm, and then discuss difficulties and possible routes both towards ultrafast operation and next possible steps for power scaling.

physics.optics↗

Single-cycle, MHz-repetition rate THz source with 66 mW of average power

We demonstrate THz generation using the tilted pulse front method in Lithium Niobate, driven at unprecedented high average power of more than 100 W and at 13.3 MHz repetition rate, provided by a compact amplifier-free modelocked thin-disk oscillator. The conversion efficiency was optimized with respect to pump spot size and pump pulse duration, enabling us to generate a maximum THz average power of 66 mW, which is the highest reported to date from a laser-driven, few-cycle THz source. Furthermore, we identify beam walk-off as the main obstacle that currently limits the conversion efficiency in this excitation regime (with moderate pulse energies and small spot sizes). Further upscaling to the watt level and beyond is within reach, paving the way for linear and nonlinear high-average power THz spectroscopy experiments with exceptional signal-to-noise ratio at MHz repetition rates.

physics.optics↗

Efficient Spectral Broadening in the 100-W Average Power Regime Using Gas Filled Kagome HC-PCF and Pulse Compression

We present nonlinear pulse compression of a high-power SESAM-modelocked thin-disk laser (TDL) using an Ar-filled hypocycloid-core Kagome Hollow-Core Photonic Crystal Fiber (HC-PCF). The output of the modelocked Yb:YAG TDL with 127 W average power, a pulse repetition rate of 7 MHz, and a pulse duration of 740 fs was spectrally broadened 16-fold while propagating in a Kagome HC-PCF containing 13 bar of static Argon gas. Subsequent compression tests performed using 8.4% of the full available power resulted in a pulse duration as short as 88 fs using the spectrally broadened output from the fiber. Compressing the full transmitted power through the fiber (118 W) could lead to a compressed output of >100 W of average power and >100 MW of peak power with an average power compression efficiency of 88%. This simple laser system with only one ultrafast laser oscillator and a simple single-pass fiber pulse compressor, generating both high peak power >100 MW and sub-100-fs pulses at megahertz repetition rate, is very interesting for many applications such as high harmonic generation and attosecond science with improved signal-to-noise performance.

physics.optics↗

Gigahertz Self-referenceable Frequency Comb from a Semiconductor Disk Laser

We present a 1.75-GHz self-referenceable frequency comb from a vertical external-cavity surface-emitting laser (VECSEL) passively modelocked with a semiconductor saturable absorber mirror (SESAM). The VECSEL delivers 231-fs pulses with an average power of 100 mW and is optimized for stable and reliable operation. The optical spectrum was centered around 1038 nm and nearly transform-limited with a full width half maximum (FWHM) bandwidth of 5.5 nm. The pulses were first amplified to an average power of 5.5 W using a backward-pumped Yb-doped double-clad large mode area (LMA) fiber and then compressed to 85 fs with 2.2 W of average power with a passive LMA fiber and transmission gratings. Subsequently, we launched the pulses into a highly nonlinear photonic crystal fiber (PCF) and generated a coherent octave-spanning supercontinuum (SC). We then detected the carrier-envelope offset (CEO) frequency (fCEO) beat note using a standard f-to-2f-interferometer. The fCEO exhibits a signal-to-noise ratio of 17 dB in a 100-kHz resolution bandwidth and a FWHM of 10 MHz. To our knowledge, this is the first report on the detection of the fCEO from a semiconductor laser, opening the door to fully stabilized compact frequency combs based on modelocked semiconductor disk lasers.

physics.optics↗