arXiv subjects

Clemens Mangler

Publications and source records attributed to Clemens Mangler.

36 records · Page 2Linked to original sources

arXiv2020

Single indium atoms and few-atom indium clusters anchored onto graphene via silicon heteroatoms

Single atoms and few-atom nanoclusters are of high interest in catalysis and plasmonics, but pathways for their fabrication and stable placement remain scarce. We report here the self-assembly of room-temperature-stable single indium (In) atoms and few-atom In clusters (2-6 atoms) that are anchored to substitutional silicon (Si) impurity atoms in suspended monolayer graphene membranes. Using atomically resolved scanning transmission electron microscopy (STEM), we find that the exact atomic arrangements of the In atoms depend strongly on the original coordination of the Si anchors in the graphene lattice: Single In atoms and In clusters with 3-fold symmetry readily form on 3-fold coordinated Si atoms, whereas 4-fold symmetric clusters are found attached to 4-fold coordinated Si atoms. All structures are produced by our fabrication route without the requirement for electron-beam induced materials modification. In turn, when activated by electron beam irradiation in the STEM, we observe in situ the formation, restructuring and translation dynamics of the Si-anchored In structures: Hexagon-centered 4-fold symmetric In clusters can (reversibly) transform into In chains or In dimers, whereas C-centered 3-fold symmetric In clusters can move along the zig-zag direction of the graphene lattice due to the migration of Si atoms during electron-beam irradiation, or transform to Si-anchored single In atoms. Our results provide a novel framework for the controlled self-assembly and heteroatomic anchoring of single atoms and few-atom clusters on graphene.

cond-mat.mtrl-sci↗

arXiv2020

CuAu, a hexagonal two-dimensional metal

Growth of two-dimensional metals has eluded materials scientists since the discovery of the atomically thin graphene and other covalently bound 2D materials. Here, we report a two-atom-thick hexagonal copper-gold alloy, grown through thermal evaporation on freestanding graphene and hexagonal boron nitride. The structures are imaged at atomic resolution with scanning transmission electron microscopy and further characterized with spectroscopic techniques. Electron irradiation in the microscope provides sufficient energy for a phase transformation of the 2D structure--atoms are released from their lattice sites with the gold atoms eventually forming face-centered cubic nanoclusters on top of 2D regions during observation. The presence of copper in the alloy enhances sticking of gold to the substrate, which has clear implications for creating atomically thin electrodes for applications utilizing 2D materials. Its practically infinite surface-to-bulk ratio also makes the 2D CuAu particularly interesting for catalysis applications.

cond-mat.mtrl-sci↗

arXiv2019

Electron-Beam Manipulation of Silicon Impurities in Single-Walled Carbon Nanotubes

The recent discovery that impurity atoms in crystals can be manipulated with focused electron irradiation has opened novel perspectives for top-down atomic engineering. These achievements have been enabled by advances in electron optics and microscope stability, but also in the preparation of suitable materials with impurity elements incorporated via ion and electron-beam irradiation or chemical means. Here it is shown that silicon heteroatoms introduced via plasma irradiation into the lattice of single-walled carbon nanotubes (SWCNTs) can be manipulated using a focused 55-60 keV electron probe aimed at neighboring carbon sites. Moving the silicon atom mainly along the longitudinal axis of large 2.7 nm diameter tubes, more than 90 controlled lattice jumps were recorded and the relevant displacement cross sections estimated. Molecular dynamics simulations show that even in 2 nm SWCNTs the threshold energies for out-of-plane dynamics are different than in graphene, and depend on the orientation of the silicon-carbon bond with respect to the electron beam as well as the local bonding of the displaced carbon atom and its neighbors. Atomic-level engineering of SWCNTs where the electron wave functions are more strictly confined than in two-dimensional materials may enable the fabrication of tunable electronic resonators and other devices.

cond-mat.mtrl-sci↗

arXiv2019

Si Substitution in Nanotubes and Graphene via Intermittent Vacancies

The properties of single-walled carbon nanotubes (SWCNTs) and graphene can be modified by the presence of covalently bound impurities. Although this can be achieved by introducing chemical additives during synthesis, that often hinders growth and leads to limited crystallite size and quality. Here, through the simultaneous formation of vacancies with low-energy argon plasma and the thermal activation of adatom diffusion by laser irradiation, silicon impurities are incorporated into the lattice of both materials. After an exposure of $\sim$1 ion/nm$^{2}$, we find Si substitution densities of 0.15 nm$^{-2}$ in graphene and 0.05 nm$^{-2}$ in nanotubes, as revealed by atomically resolved scanning transmission electron microscopy. In good agreement with predictions of Ar irradiation effects in SWCNTs, we find Si incorporated in both mono- and divacancies, with $\sim$2/3 being of the first type. Controlled inclusion of impurities in the quasi-1D and 2D carbon lattices may prove useful for applications such as gas sensing, and a similar approach might also be used to substitute other elements with migration barriers lower than that of carbon.

cond-mat.mtrl-sci↗

arXiv2019

Scanning transmission electron microscopy under controlled low-pressure atmospheres

Transmission electron microscopy (TEM) is carried out in vacuum to minimize the interaction of the imaging electrons with gas molecules while passing through the microscope column. Nevertheless, in typical devices, the pressure remains at 10^-7 mbar or above, providing a large number of gas molecules for the electron beam to crack, which can lead to structural changes in the sample. Here, we describe experiments carried out in a modified scanning TEM (STEM) instrument, based on the Nion UltraSTEM 100. In this instrument, the base pressure at the sample is around 2x10^-10 mbar, and can be varied up to 10^-6 mbar through introduction of gases directly into the objective area while maintaining atomic resolution imaging conditions. We show that air leaked into the microscope column during the experiment is efficient in cleaning graphene samples from contamination, but ineffective in damaging the pristine lattice. Our experiments also show that exposure to O2 and H2O lead to a similar result, oxygen providing an etching effect nearly twice as efficient as water, presumably due to the two O atoms per molecule. H2 and N2 environments have no influence on etching. These results show that the residual gas environment in typical TEM instruments can have a large influence on the observations, and show that chemical etching of carbon-based structures can be effectively carried out with oxygen.

cond-mat.mes-hall↗

arXiv2018

Computational insights and the observation of SiC nanograin assembly: towards 2D silicon carbide

While an increasing number of two-dimensional (2D) materials, including graphene and silicene, have already been realized, others have only been predicted. An interesting example is the two-dimensional form of silicon carbide (2D-SiC). Here, we present an observation of atomically thin and hexagonally bonded nanosized grains of SiC assembling temporarily in graphene oxide pores during an atomic resolution scanning transmission electron microscopy experiment. Even though these small grains do not fully represent the bulk crystal, simulations indicate that their electronic structure already approaches that of 2D-SiC. This is predicted to be flat, but some doubts have remained regarding the preference of Si for sp$^{3}$ hybridization. Exploring a number of corrugated morphologies, we find completely flat 2D-SiC to have the lowest energy. We further compute its phonon dispersion, with a Raman-active transverse optical mode, and estimate the core level binding energies. Finally, we study the chemical reactivity of 2D-SiC, suggesting it is like silicene unstable against molecular absorption or interlayer linking. Nonetheless, it can form stable van der Waals-bonded bilayers with either graphene or hexagonal boron nitride, promising to further enrich the family of two-dimensional materials once bulk synthesis is achieved.

cond-mat.mtrl-sci↗

arXiv2018

Direct visualization of the 3D structure of silicon impurities in graphene

We directly visualize the three-dimensional (3D) geometry and dynamics of silicon impurities in graphene as well as their dynamics by aberration-corrected scanning transmission electron microscopy. By acquiring images when the sample is tilted, we show that an asymmetry of the atomic position of the heteroatom in the projection reveals the non-planarity of the structure. From a sequence of images, we further demonstrate that the Si atom switches between up- and down- configurations with respect to the graphene plane, with an asymmetric cross-section. We further analyze the 3D structure and dynamics of a silicon tetramer in graphene. Our results clarify the out-of-plane structure of impurities in graphene by direct experimental observation and open a new route to study their dynamics in three dimensions.

physics.app-ph↗

arXiv2018

Intrinsic core level photoemission of suspended graphene

X-ray photoelectron spectroscopy of graphene is important both for its characterization and as a model for other carbon materials. Despite great recent interest, the intrinsic photoemission of its single layer has not been unambiguously measured, nor is the layer-dependence in free-standing multilayers accurately determined. We combine scanning transmission electron microscopy and Raman spectroscopy with synchrotron-based scanning photoelectron microscopy to characterize the same areas of suspended graphene samples down to the atomic level. This allows us to assign spectral signals to regions of precisely known layer number and purity. The core level binding energy of the monolayer is measured at 284.70 eV, thus 0.28 eV higher than that of graphite, with intermediate values found for few layers. This trend is reproduced by density functional theory with or without explicit van der Waals interactions, indicating that intralayer charge rearrangement dominates, but in our model of static screening the magnitudes of the shifts are underestimated by half.

cond-mat.mtrl-sci↗

arXiv2018

Revealing the 3D Structure of Graphene Defects

We demonstrate insights into the three-dimensional structure of defects in graphene, in particular grain boundaries, obtained via a new approach from two transmission electron microscopy images recorded at different angles. The structure is obtained through an optimization process where both the atomic positions as well as the simulated imaging parameters are iteratively changed until the best possible match to the experimental images is found. We first demonstrate that this method works using an embedded defect in graphene that allows direct comparison to the computationally predicted three-dimensional shape. We then applied the method to a set of grain boundary structures with misorientation angles nearly spanning the whole available range (2.6-29.8°). The measured height variations at the boundaries reveal a strong correlation with the misorientation angle with lower angles resulting in stronger corrugation and larger kink angles. Our results allow for the first time a direct comparison with theoretical predictions for the corrugation at grain boundaries and we show that the measured kink angles are significantly smaller than the largest predicted ones.

physics.app-ph↗

arXiv2018

Electron-Beam Manipulation of Silicon Dopants in Graphene

The direct manipulation of individual atoms in materials using scanning probe microscopy has been a seminal achievement of nanotechnology. Recent advances in imaging resolution and sample stability have made scanning transmission electron microscopy a promising alternative for single-atom manipulation of covalently bound materials. Pioneering experiments using an atomically focused electron beam have demonstrated the directed movement of silicon atoms over a handful of sites within the graphene lattice. Here, we achieve a much greater degree of control, allowing us to precisely move silicon impurities along an extended path, circulating a single hexagon, or back and forth between the two graphene sublattices. Even with manual operation, our manipulation rate is already comparable to the state-of-the-art in any atomically precise technique. We further explore the influence of electron energy on the manipulation rate, supported by improved theoretical modeling taking into account the vibrations of atoms near the impurities, and implement feedback to detect manipulation events in real time. In addition to atomic-level engineering of its structure and properties, graphene also provides an excellent platform for refining the accuracy of quantitative models and for the development of automated manipulation.

cond-mat.mtrl-sci↗

arXiv2018

Automated image acquisition for low-dose STEM at atomic resolution

Beam damage is a major limitation in electron microscopy that becomes increasingly severe at higher resolution. One possible route to circumvent radiation damage, which forms the basis for single-particle electron microscopy and related techniques, is to distribute the dose over many identical copies of an object. For the acquisition of low-dose data, ideally no dose should be applied to the region of interest prior to the acquisition of data. We present an automated approach that can collect large amounts of data efficiently by acquiring images in an user-defined area-of-interest with atomic resolution. We demonstrate that the stage mechanics of the Nion UltraSTEM, combined with an intelligent algorithm to move the sample, allows the automated acquisition of atomically resolved images from micron-sized areas of a graphene substrate. Moving the sample stage automatically in a regular pattern over the area-of-interest enables the collection of data from pristine sample regions without exposing them to the electron beam before recording an image. Therefore, it is possible to obtain data with minimal dose (no prior exposure from focusing), which is only limited by the minimum signal needed for data processing. This enables us to prevent beam induced damage in the sample and to acquire large datasets within a reasonable amount of time.

cond-mat.mtrl-sci↗

arXiv2017

Buckyball sandwiches

Two-dimensional (2D) materials have considerably expanded the field of materials science in the last decade. Even more recently, various 2D materials have been assembled into vertical van der Waals heterostacks, and it has been proposed to combine them with other low- dimensional structures to create new materials with hybridized properties. Here, we demonstrate the first direct images of a suspended 0D/2D heterostructure incorporating $C_{60}$ molecules between two graphene layers in a buckyball sandwich structure. We find clean and ordered $C_{60}$ islands with thicknesses down to one molecule, shielded by the graphene layers from the microscope vacuum and partially protected from radiation damage during scanning transmission electron microscopy imaging. The sandwich structure serves as a 2D nanoscale reaction chamber allowing the analysis of the structure of the molecules and their dynamics at atomic resolution.

cond-mat.mtrl-sci↗

arXiv2017

Cleaning graphene: comparing heat treatments in air and in vacuum

Surface impurities and contamination often seriously degrade the properties of two-dimensional materials such as graphene. To remove contamination, thermal annealing is commonly used. We present a comparative analysis of annealing treatments in air and in vacuum, both ex situ and "pre-situ", where an ultra-high vacuum treatment chamber is directly connected to an aberration-corrected scanning transmission electron microscope. While ex situ treatments do remove contamination, it is challenging to obtain atomically clean surfaces after ambient transfer. However, pre-situ cleaning with radiative or laser heating appears reliable and well suited to clean graphene without undue damage to its structure.

cond-mat.mtrl-sci↗

arXiv2016

Single-atom spectroscopy of phosphorus dopants implanted into graphene

One of the keys behind the success of the modern semiconductor technology has been the ion implantation of silicon, which allows its electronic properties to be tailored. For similar purposes, heteroatoms have been introduced into carbon nanomaterials both during growth and using post-growth methods. However, due to the nature of the samples, it has been challenging to determine whether the heteroatoms have been incorporated into the lattice as intended, with direct observations so far being limited to N and B dopants, and incidental Si impurities. Furthermore, ion implantation of these materials is more challenging due to the requirement of very low ion energies and atomically clean surfaces. Here, we provide the first atomic-resolution imaging and electron energy loss spectroscopy (EELS) evidence of phosphorus atoms incorporated into the graphene lattice by low-energy ion irradiation. The measured P L-edge response of an single-atom EELS spectrum map shows excellent agreement with an ab initio spectrum simulation, conclusively identifying the P in a buckled substitutional configuration. Our results demonstrate the viability of phosphorus as a lattice dopant in $sp^2$-bonded carbon structures and provide its unmistakeable fingerprint for further studies.

cond-mat.mtrl-sci↗

arXiv2016

Isotope analysis in the transmission electron microscope

The Ångström-sized probe of the scanning transmission electron microscope can visualize and collect spectra from single atoms. This can unambiguously resolve the chemical structure of materials, but not their isotopic composition. Here we differentiate between two isotopes of the same element by quantifying how likely the energetic imaging electrons are to eject atoms. First, we measure the displacement probability in graphene grown from either $^{12}$C or $^{13}$C and describe the process using a quantum mechanical model of lattice vibrations coupled with density functional theory simulations. We then test our spatial resolution in a mixed sample by ejecting individual atoms from nanoscale areas spanning an interface region that is far from atomically sharp, mapping the isotope concentration with a precision better than 20%. Although we use a scanning instrument, our method should be applicable to any atomic resolution transmission electron microscope and to other low-dimensional materials.

physics.ins-det↗

arXiv2014

Silicon-carbon bond inversions driven by 60 keV electrons in graphene

We demonstrate that 60 keV electron irradiation drives the diffusion of threefold coordinated Si dopants in graphene by one lattice site at a time. First principles simulations reveal that each step is caused by an electron impact on a C atom next to the dopant. Although the atomic motion happens below our experimental time resolution, stochastic analysis of 38 such lattice jumps reveals a probability for their occurrence in a good agreement with the simulations. Conversions from three- to fourfold coordinated dopant structures and the subsequent reverse process are significantly less likely than the direct bond inversion. Our results thus provide a model of non-destructive and atomically precise structural modification and detection for two-dimensional materials.

cond-mat.mes-hall↗

arXiv2014

Imaging Atomic-Level Random Walk of a Point Defect in Graphene

Deviations from the perfect atomic arrangements in crystals play an important role in affecting their properties. Similarly, diffusion of such deviations is behind many microstructural changes in solids. However, observation of point defect diffusion is hindered both by the difficulties related to direct imaging of non-periodic structures and by the time scales involved in the diffusion process. Here, instead of imaging thermal diffusion, we stimulate and follow the migration of a divacancy through graphene lattice using a scanning transmission electron microscope operated at 60 kV. The beam-activated process happens on a timescale that allows us to capture a significant part of the structural transformations and trajectory of the defect. The low voltage combined with ultra-high vacuum conditions ensure that the defect remains stable over long image sequences, which allows us for the first time to directly follow the diffusion of a point defect in a crystalline material.

cond-mat.mtrl-sci↗

arXiv2013

Electronic Transport in Composites of Graphite Oxide with Carbon Nanotubes

We show that the presence of electrically insulating graphite oxide (GO) within a single wall carbon nanotube network strongly enhances electrical conductivity, whereas reduced graphite oxide, even though electrically conductive, suppresses electrical conductivity within a composite network with single wall carbon nanotubes. Measurements of Young modulus and of Raman spectra strongly support our interpretation of the indirect role of the oxide groups, present in graphite oxide within the single wall carbon nanotubes/graphite oxide composite, through electronic doping of metallic single wall carbon nanotubes.

cond-mat.mtrl-sci↗