arXiv subjects

Cristiano M. B. Cordeiro

Publications and source records attributed to Cristiano M. B. Cordeiro.

14 recordsLinked to original sources

arXiv2026

Ultrawide dynamic bandwidth modulation of an antiresonant nanoweb hollow-core fiber

We experimentally demonstrate an acoustically modulated antiresonant nanoweb hollow-core fiber (N-HCF) for the first time. The N-HCF contains two off-center air cores with a diameter difference of 5 microns, separated by a nanoweb of silica. We analytically simulate the influence of the N-HCF core diameter, cladding wall, and nanoweb thicknesses on the confinement losses, effective indices, and beatlengths of the guided fundamental (HE11) and higher-order modes (TE01, TM01), from 750 to 1200 nm. The phase-matching of the acoustic waves and modal beatlengths is also estimated and discussed. The fabricated 3.6 cm long acousto-optic device modulates record-wide bandwidths (up to 450 nm) while providing high modulation depths (up to 8 dB) at low drive voltages (10 V). Simulated and measured results provide useful insights for designing, modeling, and characterizing the N-HCF transmission spectrum and modulation performance. These achievements lead to highly efficient, compact, and fast all-fiber sensors and modulators promising for application in pulsed fiber lasers.

physics.optics↗

arXiv2025

Laser-Induced Deposition of Single-Walled Carbon Nanotubes in Suspended Core Optical Fibers

We experimentally demonstrate laser-driven deposition of single-walled carbon nanotubes (CNTs) in suspended core fibers (SCFs) for the first time. Two samples for each SCF type with three (SCF1) and four (SCF2) air holes are individually inserted in a syringe loaded with a 0.5 mL solution of CNTs dispersed in methanol, and a high-power laser at 980 nm is injected into the fibers during distinct periods: SCF1 (20 and 30 minutes), SCF2 (5 and 10 minutes). The CNT solution thermally expands, accelerating and depositing nanotubes on the fiber tip. The material and dimensions of the CNTs deposited on the SCFs' cross-section are characterized, revealing nanotube bundles increasing in thickness from the fiber core to the bridges and inside the holes. The average maximum CNT thickness widening the bridge edges is, respectively, for SCF1 (2.8 and 2 microns) and SCF2 (1.7 and 1.3 microns). These achievements are significant for nanoparticle deposition and fabrication of microscale devices on tips and inside specialty and hollow fibers, enabling innovative fiber sensors, mode-locked fiber lasers, in-fiber acousto-optic modulators, and broadband photoacoustic transmitters for imaging and neurostimulation.

physics.optics↗

arXiv2025

Laser-assisted deposition of carbon nanotubes in optical fibers with multiparameter control

We demonstrate a new method to deposit carbon nanotubes (CNT) on optical fibers based on a syringe-loaded CNT solution axially aligned to the fiber tip. A laser generates an optical tweezer in a water-based CNT solution, depositing nanotubes over the fiber cross-section. The parameters are adjusted, resulting in two deposited CNT layers with distinct thicknesses. This setup employs smaller solution volumes than those commonly used in beckers, providing high confinement, protection, and interaction of nanotubes, laser, and fiber, offering a promising alternative for real-time monitoring, which are significant to the development of industrial fiber lasers and biomedical optoacoustic devices.

physics.optics↗

arXiv2025

In-series Multimode Interference Sensors and Fabry-Perot Interferometers for Enhanced Wavelength Shift Resolving Capabilities

We report on the development of a refractive index sensor obtained by using a singlemode-multimode-singlemode (SMS) structure and a Fabry-Perot interferometer (FPI) set into an in-series configuration. Due to the self-imaging phenomenon, the SMS structure - formed by splicing a no-core fiber between two singlemode fibers -, provides a broad spectral peak whose central wavelength position is sensitive to variations in the refractive index of the medium surrounding the fiber. In turn, thanks to the in-series SMS-FPI configuration, the sensor's reflection spectrum exhibits the SMS spectral signature modulated by FPI fringes. This readily allows for reducing the width of the spectral features monitored during the sensing measurements, thus enhancing the capabilities of adequately resolving the corresponding spectral shifts. The FPIs reported in this investigation have been fabricated by using two different methods, namely by forming an air-gap FPI between the cleaved ends of two singlemode optical fibers, and by casting a polymeric film onto a connectorized fiber end tip. In the first configuration, the distance between the two cleaved fiber ends could be varied to tune the FPI's free spectral range, hence allowing for tailoring the widths of the spectral oscillations to be monitored during the sensing measurements. Alternatively, the second configuration, while avoiding the use of motorized translation stages, provides a more versatile option for applications. Thus, we understand that our work expands the application of multimode interference and FPIs in sensing scenarios, providing new opportunities for probing physical and chemical parameters by exploring their combined response.

physics.optics↗

arXiv2025

Refractometry with filled antiresonant capillary fibers

We demonstrate the realization of refractometric measurements relying on the study of the transmission spectrum of filled capillary fibers. In this method, the fiber is filled with a material with a lower refractive index than that of the capillary and, due to antiresonant guidance mechanism, a characteristic transmission spectrum alternating high and low attenuation regions is obtained. The refractive index data is hence extracted by analyzing the spectral positions of the fiber transmission bands. While this method holds broad applicability for diverse materials, we specifically applied this technique to characterize agarose gels, due to their interest as a promising optical material. By analyzing the transmission spectra across the 600-900 nm wavelength range, we determined the dispersion trend for agar gels prepared with varying water and glycerol concentrations and estimated their first-order Sellmeier coefficients. The reported refractometric method provides a simple and promising means for characterizing the dispersion properties of a wide range of materials, including gels, solids, and liquids, also opening new possibilities for the development of new refractive index sensing platforms.

physics.optics↗

arXiv2024

Widely tunable dual acousto-optic interferometric device based on a hollow core fiber

An all-fiber dual Mach-Zehnder interferometer (MZI) based on an acoustically modulated hollow-core fiber (HCF) is experimentally demonstrated for the first time. By attaching an acoustic driver in between the fixed ends of an HCF, we fabricated two acousto-optic modulators (AOMs) with distinct driver positions, allowing for synchronizing two in-line MZIs inside the HCF. The first MZI is set by two acoustic long-period gratings separated by a second MZI formed at the fiber and driver attaching region. We show that this setup enables frequency-tuning of the coupling between the fundamental and higher-order modes in the HCF. Additionally, we simulate and analyze the HCF modal couplings and MZIs' modulated spectra under distinct device parameters using the transfer matrix method. The new AOM-MZI enables tuning of the MZIs free spectral range by adjusting 1 Hz of the electrical frequency, which is promising to modulate multiwavelength filters, sensors and fiber lasers.

physics.optics↗

arXiv2024

Highly efficient compact acousto-optic modulator based on a hybrid-lattice hollow core fiber

We demonstrate the acousto-optic modulation of a hybrid-lattice hollow core fiber (HL-HCF) for the first time. For many years, optical fibers with reduced diameters have been the main solution to increase the interaction of acoustic and optical waves. However, the high drive voltages and large modulator components still employed drastically affect the efficiency and miniaturization of these devices. Here, we experimentally show that combining Kagomé and tubular lattices in HL-HCFs allows for enhancing the amplification of the acoustic waves and the modulation of the guided optical modes thus providing high modulation efficiency even when using a fiber with a 240 um diameter. To the best of our knowledge, the measured HL-HCF's modulation efficiency (1.3 dB/V) is the highest compared to devices employing reduced diameter fibers. Additionally, we demonstrate a compact acousto-optic modulator with driver dimensions smaller than the HL-HCF diameter. Overall, our results show a promising alternative to solve the compromise of speed, efficiency, and compactness for integration with microscale all-fiber photonic devices.

physics.optics↗

arXiv2024

Highly efficient interaction of a tubular-lattice hollow-core fiber and flexural acoustic waves: design, characterization and analysis

The modulation efficiency of a tubular-lattice hollow-core fiber (HCF) by means of flexural acoustic waves is investigated in detail for the first time. The main acousto-optic properties of the HCF are evaluated employing 2D and 3D models based on the finite element method. The induced coupling of the fundamental and first higher-order modes is simulated in the wavelength range from 743 to 1355 nm. Significant acoustic (amplitude, period, strain, energy) and optical parameters (effective index, beat length, birefringence, coupling coefficient) are analyzed. The simulations are compared to experimental results, indicating higher modulation performance in HCFs compared to standard optical fibers. In addition, useful insights into the design and fabrication of all-fiber acousto-optic devices based on HCFs are provided, enabling potential application in tunable spectral filters and mode-locked fiber lasers.

physics.optics↗

arXiv2024

High-temperature sensing using a hollow-core fiber with thick cladding tubes

We report on high-temperature sensing measurements using a tubular-lattice hollow-core photonic crystal fiber displaying a microstructure formed of eight 2.4 um-thick cladding tubes. The larger thickness of our fiber's cladding tubes compared to other hollow fibers operating in the visible and infrared ranges entails multiple narrow transmission bands in its transmission spectrum (6 bands in the spectral range between 400 nm and 950 nm) and benefits the realization of the temperature sensing measurements. The principle of operation of our device is based on the thermo-optic effect and thermal expansion-induced spectral shifts of the fiber transmission bands due to temperature variations. To study the sensor operation, we monitored the fiber transmission bands' spectral positions from room temperature to 1085 oC in both ramp-up and ramp-down scenarios. Additionally, we investigated the optimization opportunities by assessing an analytical model describing the fiber transmission characteristics and discussed the alternatives for enhancing the sensor performance. Moreover, our fiber characterization experiments revealed a consistent confinement loss trend aligned with the scaling laws in tubular-lattice hollow-core fibers. We thus understand that the results presented in this manuscript highlight a relevant path for the development of temperature sensors based on microstructured hollow-core optical fibers endowed with thick cladding tubes.

physics.optics↗

arXiv2023

All-fiber broadband spectral acousto-optic modulation of a tubular-lattice hollow-core optical fiber

We demonstrate a broadband acousto-optic notch filter based on a tubular-lattice hollow-core fiber for the first time. The guided optical modes are modulated by acoustically induced dynamic long-period gratings along the fiber. The device is fabricated employing a short interaction length (7.7 cm) and low drive voltages (10 V). Modulated spectral bands with 20 nm half-width and maximum depths greater than 60 % are achieved. The resonant notch wavelength is tuned from 743 to 1355 nm (612 nm span) by changing the frequency of the electrical signal. The results indicate a broader tuning range compared to previous studies using standard and hollow-core fibers. It further reveals unique properties for reconfigurable spectral filters and fiber lasers, pointing to the fast switching and highly efficient modulation of all-fiber photonic devices.

physics.optics↗

arXiv2022

Hollow-core fiber-based speckle displacement sensor

The research enterprise towards achieving high-performance hollow-core photonic crystal fibers has led to impressive advancements in the latest years. Indeed, using this family of fibers becomes nowadays an overarching strategy for building a multitude of optical systems ranging from beam delivery devices to optical sources and sensors. In most applications, an effective single-mode operation is desired and, as such, the fiber microstructure or the light launching setups are typically designed for achieving such a behavior. Alternatively, one can identify the use of large-core multimode hollow-core fibers as a promising avenue for the development of new photonic devices. Thus, in this manuscript, we propose and demonstrate the utilization of a large-core tubular-lattice fiber for accomplishing a speckle-based displacement sensor, which has been built up by inserting and suitably dislocating a single-mode fiber inside the void core of the hollow fiber. The work reported herein encompasses both simulation and experimental studies on the evolution of the multimode intensity distributions within the device as well as the demonstration of a displacement sensor with an estimated resolution of 0.7 μm. We understand that this investigation identifies a new opportunity for the employment of large-core hollow fibers within the sensing framework hence widening the gamut of applications of this family of fibers.

physics.optics↗

arXiv2022

Hollow-core photonic crystal fibers for Power-over-Fiber systems

Research achievements in hollow-core photonic crystal fibers technology allow ascertaining such fibers as outstanding platforms for delivering high-power laser beams. Indeed, the key property underlying the success of this family of optical fibers for high-power beam delivery is their capability of efficiently transmitting light through empty space with minimal interaction with the fiber microstructure. In this context, here we widen the framework of hollow-core fiber-based beam delivery applications by demonstrating their utilization as promising platforms for Power-over-Fiber systems. Thus, we report on the use of a tubular-lattice hollow-core fiber to deliver a watt-level continuous-wave laser beam onto a photovoltaic converter and activate a representative camera circuit. We believe that the experiments reported herein allow identifying hollow-core fibers as eligible candidates for next-generation Power-over-Fiber devices potentially able to lift the power restrictions of current solid-core fiber-based Power-over-Fiber systems.

physics.optics↗

arXiv2021

Angle-resolved hollow-core fiber-based curvature sensor

We propose and theoretically study a new hollow-core fiber-based curvature sensor with the capability of detecting both bending magnitude and angle (direction). The new sensor relies on a tubular-lattice fiber that encompasses, in its microstructure, tubes with three different thicknesses. By adequately choosing the placement of the tubes within the fiber cross-section, and by exploring the spectral shifts of the fiber transmitted spectrum due to the curvature-induced mode field distributions' displacements, we demonstrate a multi-axis bending sensor. In the proposed sensor, curvature radii and angles are retrieved via a suitable calibration routine, which is based on conveniently adjusting empirical functions to the sensor response. Evaluation of the sensor performance for selected cases allowed to determine the curvature radii and angles with percentual errors of less than 7%. The approach proposed herein provides a promising path for the accomplishment of new curvature sensors able to resolve both the curvature magnitude and angle.

physics.optics↗

arXiv2016

Brillouin Scattering Self-Cancellation

The interaction between light and acoustic phonons is strongly modified in sub-wavelength confinement, and has led to the demonstration and control of Brillouin scattering in photonic structures such as nano-scale optical waveguides and cavities. Besides the small optical mode volume, two physical mechanisms come into play simultaneously: a volume effect caused by the strain induced refractive index perturbation (known as photo-elasticity), and a surface effect caused by the shift of the optical boundaries due to mechanical vibrations. As a result proper material and structure engineering allows one to control each contribution individually. In this paper, we experimentally demonstrate the perfect cancellation of Brillouin scattering by engineering a silica nanowire with exactly opposing photo-elastic and moving-boundary effects. This demonstration provides clear experimental evidence that the interplay between the two mechanisms is a promising tool to precisely control the photon-phonon interaction, enhancing or suppressing it.

physics.optics↗