arXiv subjects

D. C. Larbalestier

Publications and source records attributed to D. C. Larbalestier.

At least 55 records · Page 3Linked to original sources

arXiv2007

Nanoscale grains, high irreversibility field, and large critical current density as a function of high energy ball milling time in C-doped magnesium diboride

Magnesium diboride (MgB2) powder was mechanically alloyed by high energy ball milling with C to a composition of Mg(B0.95C0.05)2 and then sintered at 1000 C in a hot isostatic press. Milling times varied from 1 minute to 3000 minutes. Full C incorporation required only 30-60 min of milling. Grain size of sintered samples decreased with increased milling time to less than 30 nm for 20-50 hrs of milling. Milling had a weak detrimental effect on connectivity. Strong irreversibility field (H*) increase (from 13.3 T to 17.2 T at 4.2 K) due to increased milling time was observed and correlated linearly with inverse grain size (1/d). As a result, high field Jc benefited greatly from lengthy powder milling. Jc(8 T, 4.2 K) peaked at > 80,000 A/cm2 with 1200 min of milling compared with only ~ 26,000 A/cm2 for 60 min of milling. This non-compositional performance increase is attributed to grain refinement of the unsintered powder by milling, and to the probable suppression of grain growth by milling-induced MgO nano-dispersions.

cond-mat.supr-con↗

arXiv2006

Atmospheric conditions and their effect on ball-milled magnesium diboride

Magnesium diboride bulk pellets were fabricated from pre-reacted MgB2 powder ball milled with different amounts of exposure to air. Evidence of increased electron scattering including increased resistivity, depressed Tc, and enhanced Hc2 of the milled and heat treated samples were observed as a result of increased contact with air. These and other data were consistent with alloying with carbon as a result of exposure to air. A less clear trend of decreased connectivity associated with air exposure was also observed. In making the case that exposure to air should be considered a doping process, these results may explain the wide varibability of "undoped" MgB2 properties extant in the literature.

cond-mat.supr-con↗

arXiv2006

Mechanisms of weak thickness dependence of the critical current density in strong pinning ex situ metal-organic-deposition route YBa2Cu3O7-x coated conductors

We report on the thickness dependence of the superconducting characteristics including critical current Ic, critical current density Jc, transition temperature Tc, irreversibility field Hirr, bulk pinning force plot Fp(H), and the normal state resistivity curve measured after successive ion milling of ~ 1 um thick high Ic YBa2Cu3O7-x films made by an ex situ metal-organic deposition process on Ni-W rolling-assisted biaxially textured substrates (RABiTS). Contrary to many recent data, mostly on in situ pulsed laser deposition (PLD) films, which show strong depression of Jc with increasing film thickness t, our films exhibit only a weak dependence of Jc on t. The two better textured samples had full cross-section average Jc,avg(77K,0T) ~ 4 MA/cm2 near the buffer layer interface and ~3 MA/cm2 at full thickness, despite significant current blocking due to ~30% porosity in the film. Taking account of the thickness dependence of the porosity, we estimate that the local, vortex-pinning current density is essentially independent of thickness, while accounting for the additional current-blocking effects of grain boundaries leads to local, vortex-pinning Jc values well above 5 MA/cm2. Such high local Jc values are produced by strong three-dimensional vortex pinning which subdivides vortex lines into weakly coupled segments much shorter than the film thickness.

cond-mat.supr-con↗

arXiv2006

Resistivity and Magneto-Optical Evidence for Variable and Incomplete Connectivity in Dense, High Critical Current Density C-alloyed Magnesium Diboride

Carbon-doped magnesium diboride was fabricated from pre-reacted pure MgB2 by mechanical alloying. The sample set had excellent critical current densities Jc(8T,4.2K) ranging from 15-60 kA/cm2, depending on composition. Magneto-optical imaging detected regions up to 0.5 mm in size which were nearly 100% dense with Jc 2-6 times that of the matrix. Evaluation of resistivity curves using the Rowell method predicts that only 10-50% of the cross sectional area carries the normal state measurement current, suggesting that considerable increases in Jc in these ~80% dense MgB2 samples would be possible with complete grain and particle connectivity.

cond-mat.supr-con↗

arXiv2005

Improved Hc2 in Bulk-Form Magnesium Diboride by Mechanical Alloying With Carbon

High energy milling of MgB2 pre-reacted powder renders the material largely amorphous through extreme mechanical deformation and is suitable for mechanically alloying MgB2 with dopants including carbon. Bulk samples of milled C and MgB2 powders subjected to hot isostatic pressing and Mg vapor annealing have achieved critical fields in excess of 32T and critical current density approaching 10^6 A/cm^2.

cond-mat.supr-con↗

arXiv2005

The upper critical field of filamentary Nb3Sn conductors

We have examined the upper critical field of a large and representative set of present multi-filamentary Nb3Sn wires and one bulk sample over a temperature range from 1.4 K up to the zero field critical temperature. Since all present wires use a solid-state diffusion reaction to form the A15 layers, inhomogeneities with respect to Sn content are inevitable, in contrast to some previously studied homogeneous samples. Our study emphasizes the effects that these inevitable inhomogeneities have on the field-temperature phase boundary. The property inhomogeneities are extracted from field-dependent resistive transitions which we find broaden with increasing inhomogeneity. The upper 90-99 % of the transitions clearly separates alloyed and binary wires but a pure, Cu-free binary bulk sample also exhibits a zero temperature critical field that is comparable to the ternary wires. The highest mu0Hc2 detected in the ternary wires are remarkably constant: The highest zero temperature upper critical fields and zero field critical temperatures fall within 29.5 +/- 0.3 T and 17.8 +/- 0.3 K respectively, independent of the wire layout. The complete field-temperature phase boundary can be described very well with the relatively simple Maki-DeGennes model using a two parameter fit, independent of composition, strain state, sample layout or applied critical state criterion.

cond-mat.supr-con↗

arXiv2004

Thermally-activated current transport in MgB_2 films

Thermally-activated flux flow (TAFF) resistivity above the irreversibility field is reported for two different c-axis textured MgB_2 superconducting films. Transport measurements at different perpendicular magnetic fields 0 < B < 9 T and temperatures from 5 to 40K reveal TAFF Ohmic resistivity described by the Arrhenius law with the quadratic field dependence of the activation energy. Our transport measurements on bulk MgB_2 ceramic samples also show the TAFF behavior, but do not show the quadratic field dependence of U(T,B). We explain our results in terms of thermally-activated drift of pre-existing quenched dislocations in the vortex lattice. Our results indicate that thermal fluctuations can be essential in determining the irreversibility field in MgB2 though to a much lesser extent than in high-temperature superconductors.

cond-mat.supr-con↗

arXiv2004

Simulations of the effects of tin composition gradients on the superconducting properties of Nb3Sn conductors

In powder-in-tube (PIT) Nb3Sn composites, the A15 phase forms between a central tin-rich core and a coaxial Nb tube, thus causing the tin content and superconducting properties to vary with radius across the A15 layer. Since this geometry is also ideal for magnetic characterization of the superconducting properties with the field parallel to the tube axis, a system of concentric shells with varying tin content was used to simulate the superconducting properties, the overall severity of the Sn composition gradient being defined by an index N. Using well-known scaling relationships and property trends developed in an earlier experimental study, the critical current density for each shell was calculated, and from this the magnetic moment of each shell was found. By summing these moments, experimentally measured properties such as pinning-force curves and Kramer plots could be simulated. We found that different tin profiles have only a minor effect on the shape of Kramer plots, but a pronounced effect on the irreversibility fields defined by the extrapolation of Kramer plots. In fact, these extrapolated values H_K are very close to a weighted average of the superconducting properties across the layer for all N. The difference between H_K and the upper critical field commonly seen in experiments is a direct consequence of the different ways measurements probe the simulated Sn gradients. Sn gradients were found to be significantly deleterious to the critical current density Jc, since reductions to both the elementary pinning force and the flux pinning scaling field H_K compound the reduction in Jc. The simulations show that significant gains in Jc of Nb3Sn strands might be realized by circumventing strong compositional gradients of tin.

cond-mat.supr-con↗

arXiv2004

High-field superconductivity in alloyed MgB2 thin films

We investigated the effect of alloying on the upper critical field $H_{c2}$ in 12 $MgB_2$ films, in which disorder was introduced by growth, carbon doping or He-ion irradiation, finding a significant $H_{c2}$ enhancement in C-alloyed films, and an anomalous upward curvature of $H_{c2}(T)$. Record high values of $H_{c2}^{\perp}(4.2) \simeq 35T$ and $H_{c2}\|(4.2) \simeq 51T$ were observed perpendicular and parallel to the ab plane, respectively. The temperature dependence of $H_{c2}(T)$ is described well by a theory of dirty two-gap superconductivity. Extrapolation of the experimental data to T=0 suggests that $H_{c2}\|(0)$ approaches the paramagnetic limit of $\sim 70T$.

cond-mat.supr-con↗

arXiv2003

Through-thickness superconducting and normal-state transport properties revealed by thinning of thick film ex situ YBa2Cu3O7-x coated conductors

A rapid decrease in the critical current density (Jc) of YBa2Cu3O7-x (YBCO) films with increasing film thickness has been observed for multiple YBCO growth processes. While such behavior is predicted from 2D collective pinning models under certain assumptions, empirical observations of the thickness dependence of Jc are believed to be largely processing dependent at present. To investigate this behavior in ex situ YBCO films, 2.0 and 2.9 um thick YBCO films on ion beam assisted deposition (IBAD) - yttria stabilized zirconia (YSZ) substrates were thinned and repeatedly measured for rho(T) and Jc(H). The 2.9 um film exhibited a constant Jc(77K,SF) through thickness of ~1 MA/cm2 while the 2.0 um film exhibited an increase in Jc(77K,SF) as it was thinned. Neither film offered evidence of significant dead layers, suggesting that further increases in critical current can be obtained by growing thicker YBCO layers.

cond-mat.supr-con↗

arXiv2003

Very high upper critical fields in MgB2 produced by selective tuning of impurity scattering

We report a significant enhancement of the upper critical field $H_{c2}$ of different $MgB_2$ samples alloyed with nonmagnetic impurities. By studying films and bulk polycrystals with different resistivities $ρ$, we show a clear trend of $H_{c2}$ increase as $ρ$ increases. One particular high resistivity film had zero-temperature $H_{c2}(0)$ well above the $H_{c2}$ values of competing non-cuprate superconductors such as $Nb_3Sn$ and Nb-Ti. Our high-field transport measurements give record values $H_{c2}^\perp (0) \approx 34T$ and $H_{c2}\|(0) \approx 49 T$ for high resistivity films and $H_{c2}(0)\approx 29 T$ for untextured bulk polycrystals. The highest $H_{c2}$ film also exhibits a significant upward curvature of $H_{c2}(T)$, and temperature dependence of the anisotropy parameter $γ(T) = H_{c2}\|/ H_{c2}^\perp$ opposite to that of single crystals: $γ(T)$ decreases as the temperature decreases, from $γ(T_c) \approx 2$ to $γ(0) \approx 1.5$. This remarkable $H_{c2}$ enhancement and its anomalous temperature dependence are a consequence of the two-gap superconductivity in $MgB_2$, which offers special opportunities for further $H_{c2}$ increase by tuning of the impurity scattering by selective alloying on Mg and B sites. Our experimental results can be explained by a theory of two-gap superconductivity in the dirty limit. The very high values of $H_{c2}(T)$ observed suggest that $MgB_2$ can be made into a versatile, competitive high-field superconductor.

cond-mat.supr-con↗

arXiv2002

Local Measurement of Current Density by Magneto-Optical Current Reconstruction in Normally and Overpressure Processed Bi-2223 Tapes

Magneto-optical current reconstruction has been used for detailed analysis of the local critical current density (Jc) variation in monocore Bi-2223 tapes. We find, even in high quality tapes with bulk transport Jc ~ 40 kA/cm^2 (77K, 0T), that there exist local regions which possess current densities of more than 200 kA/cm^2. Overpressure processing at 148 bar significantly improved Jc to 48 kA/cm^2 by improving the connectivity. For the overpressure-processed sample we find that the current distribution is more uniform and that the maximum local current density at 77 K is increased almost to 300 kA/cm^2.

cond-mat.supr-con↗

arXiv2002

Significant enhancement of irreversibility field in clean-limit bulk MgB2

Low resistivity ("clean") MgB2 bulk samples annealed in Mg vapor show an increase in upper critical field Hc2(T) and irreversibility field Hirr(T) by a factor of 2 in both transport and magnetic measurements. The best sample displayed Hirr above 14 T at 4.2 K and 6 T at 20 K. These changes were accompanied by an increase of the 40 K resistivity from 1.0 to 18 microohm-cm and a lowering of the resistivity ratio from 15 to 3, while the critical temperature Tc decreased by only 1-2 K. These results point the way to make prepare MgB2 attractive for magnet applications.

cond-mat.supr-con↗

arXiv2002

High Critical Current Density and Improved Irreversibility Field in Bulk MgB2 Made By A Scaleable, Nanoparticle Addition Route

Bulk samples of MgB2 were prepared with 5, 10, and 15% wt.% Y2O3 nanoparticles added using a simple solid-state reaction route. Transmission electron microscopy (TEM) showed a fine nanostructure consisting of ~3-5 nm YB4 nanoparticles embedded within MgB2 grains of ~400 nm size. Compared to an undoped control sample, an improvement in the in-field critical current density Jc was observed, most notably for 10% doping. At 4.2K, the lower bound Jc value was ~2x105A.cm-2 at 2T. At 20K, the corresponding value was ~8x104A.cm-2. Irreversibility fields were ~11.5 T at 4.2K and 5.5T at 20K, compared to ~4T and ~8T, respectively, for high-pressure synthesized bulk samples.

cond-mat.supr-con↗

arXiv2002

Synthesis and Properties of c-axis Oriented Epitaxial MgB2 Thin Films

We report the growth and properties of epitaxial MgB2 thin films on (0001) Al2O3 substrates. The MgB2 thin films were prepared by depositing boron films via RF magnetron sputtering, followed by a post-deposition anneal at 850C in magnesium vapor. X-ray diffraction and cross-sectional TEM reveal that the epitaxial MgB2 films are oriented with their c-axis normal to the (0001) Al2O3 substrate and a 30 degree rotation in the ab-plane with respect to the substrate. The critical temperature was found to be 35 K and the anisotropy ratio, Hc2(parallel to the film) / Hc2(pendicular to the film), about 3 at 25K. The critical current densities at 4.2 K and 20 K (at 1 T perpendicular magnetic field) are 5x10E6 A/cm2 and 1x10E6 A/cm2, respectively. The controlled growth of epitaxial MgB2 thin films opens a new avenue in both understanding superconductivity in MgB2 and technological applications.

cond-mat.supr-con↗

arXiv2002

Flux flow of Abrikosov-Josephson vortices along grain boundaries in high-temperature superconductors

We show that low-angle grain boundaries (GB) in high-temperature superconductors exhibit intermediate Abrikosov vortices with Josephson cores, whose length $l$ along GB is smaller that the London penetration depth, but larger than the coherence length. We found an exact solution for a periodic vortex structure moving along GB in a magnetic field $H$ and calculated the flux flow resistivity $R_F(H)$, and the nonlinear voltage-current characteristics. The predicted $R_F(H)$ dependence describes well our experimental data on $7^{\circ}$ unirradiated and irradiated $YBa_2Cu_3O_7$ bicrystals, from which the core size $l(T)$, and the intrinsic depairing density $J_b(T)$ on nanoscales of few GB dislocations were measured for the first time. The observed temperature dependence of $J_b(T)=J_{b0}(1-T/T_c)^2$ indicates a significant order parameter suppression in current channels between GB dislocation cores.

cond-mat.supr-con↗

arXiv2001

Core pinning by intragranular nanoprecipitates in polycrystalline MgCNi_3

The nanostructure and magnetic properties of polycrystalline MgCNi_3 were studied by x-ray diffraction, electron microscopy, and vibrating sample magnetometry. While the bulk flux-pinning force curve F_p(H) indicates the expected grain-boundary pinning mechanism just below T_c = 7.2 K, a systematic change to pinning by a nanometer-scale distribution of core pinning sites is indicated by a shift of F_p(H) with decreasing temperature. The lack of scaling of F_p(H) suggests the presence of 10 to 20% of nonsuperconducting regions inside the grains, which are smaller than the diameter of fluxon cores 2xi at high temperature and become effective with decreasing temperature when xi(T) approaches the nanostructural scale. Transmission electron microscopy revealed cubic and graphite nanoprecipitates with 2 to 5 nm size, consistent with the above hypothesis since xi(0) = 6 nm. High critical current densities, more than 10^6 A/cm^2 at 1 T and 4.2 K, were obtained for grain colonies separated by carbon. Dirty-limit behavior seen in previous studies may be tied to electron scattering by the precipitates, indicating the possibility that strong core pinning might be combined with a technologically useful upper critical field if versions of MgCNi_3 with higher T_c can be found.

cond-mat.supr-con↗

arXiv2001

Magneto-optical studies of the uniform critical state in bulk MgB2

We present a detailed magneto-optical investigation of the magnetic flux penetration in polycrystalline MgB2 slabs made by direct reaction of B and Mg. Our results unambiguously indicate a uniform, Bean critical state magnetization behavior with almost no electromagnetic granularity. From the measured magnetic flux profiles we were able to extract the temperature dependence of the critical current density Jc(T). The Jc(T) value reaches 1.8x10^5 A/cm2 at 10K and 0.12T, in good agreement with global magnetization measurements.

cond-mat.supr-con↗