arXiv subjects

D. Röhrich

Publications and source records attributed to D. Röhrich.

At least 19 recordsLinked to original sources

arXiv2026

$K^{*}(892)^0$ production and the time between freeze-outs in $^{40}$Ar+$^{45}$Sc collisions by NA61/SHINE at the CERN SPS

The analysis of the production of strange $K^{*}(892)^0$ resonances allows us to better understand the temporal evolution of high-energy nucleus--nucleus collisions. In particular, the ratio of $K^{*}(892)^0$ to charged kaon yields is used to determine the time interval between chemical and kinetic freeze-outs. In this paper, the first measurements of $K^{*}(892)^0$ production in central $^{40}$Ar+$^{45}$Sc collisions at the CERN Super Proton Synchrotron are reported. They were performed by NA61/SHINE at collision center-of-mass energies per nucleon pair $\sqrt{s_\mathrm{NN}}$ = 8.8, 11.9, 16.8 GeV. The obtained $\langle K^{*}(892)^0 \rangle/\langle K^{+} \rangle $ and $\langle K^{*}(892)^0 \rangle/\langle K^{-} \rangle$ mean multiplicity ratios are compared with corresponding results in $p$+$p$ collisions, allowing for an estimate of the time interval between chemical and thermal freeze-outs in the $^{40}$Ar+$^{45}$Sc system. These are the first such results reported for $^{40}$Ar+$^{45}$Sc collisions.

nucl-ex↗

arXiv2026

Large-scale real-time signal processing in physics experiments: The ALICE TPC FPGA pipeline

For LHC Run 3, the ALICE Time Projection Chamber was upgraded to operate in continuous readout mode. Interaction rates of up to 50 kHz in Pb-Pb collisions require real-time processing of more than 3 TB/s of raw detector data. This requirement is met by a custom FPGA-based processing pipeline that performs the complete front-end data treatment fully in-stream, including common-mode correction, pedestal subtraction, ion-tail filtering, zero suppression, and dense data packing. A central element of the design is a highly parallel common-mode correction algorithm operating directly on the streaming data. It robustly identifies signal-free readout channels on a time-bin basis and applies pad-dependent scaling to compensate for local variations in capacitive coupling in the GEM readout. In combination with pedestal subtraction and ion-tail filtering, this enables accurate baseline restoration under extreme high-occupancy conditions, preventing signal loss while efficiently suppressing noise prior to zero suppression. The pipeline operates continuously at the full detector bandwidth and reduces the raw input rate to about 900 GB/s for Pb-Pb collisions at the target interaction rate. Overall, it represents a large-scale FPGA-based real-time signal-processing implementation for high-energy physics detector readout.

physics.ins-det↗

arXiv2025

Measurements of hadron production in 90 GeV/c proton-carbon interactions

This paper presents the multiplicity of neutral and charged hadrons produced in 90 GeV$/c$ proton-carbon interactions from a dataset taken by the NA61/SHINE experiment in 2017. Particle identification via dE/dx was performed for the charged hadrons $π^\pm$, $K^\pm$, and $p / \bar{p}$; the neutral hadrons $K^0_S$, $Λ$, and $\barΛ$ were identified via an invariant mass analysis of their decays to charged hadrons. Double-differential multiplicity results as a function of laboratory momentum and polar angle are presented for each particle species; these results provide vital constraints on the predicted neutrino beam flux for current and future long-baseline neutrino oscillation experiments.

hep-ex↗

arXiv2025

Proposal from the NA61/SHINE Collaboration for update of European Strategy for Particle Physics

Building on the current program's success and driven by new physics challenges, the NA61/SHINE Collaboration proposes to continue measuring hadron production properties in reactions induced by hadron and ion beams after CERN Long Shutdown 3. These measurements are of significant interest to the heavy-ion, cosmic-ray, and neutrino physics communities and will focus on: - Investigating hadron production in the light-ion systems to explore the diagram of high-energy nuclear collisions, and to obtain new insight into the unexpected violation of isospin (flavor) symmetry recently observed by the experiment; - Measuring charm-anticharm correlations to gain unique insights into the production locality of charm and anticharm quark pairs; - Examining strangeness and multi-strangeness production to improve our understanding of the early Universe's evolution and neutron star formation; - Measuring cross sections relevant for cosmic-ray measurements, significantly boosting searches for new physics in our Galaxy; - Conducting hadron production measurements with proton, pion, and kaon beams for neutrino physics, enhancing the precision of hadron production data needed for initial neutrino flux predictions in neutrino oscillation experiments; - Measuring hadron production processes relevant for understanding the flux of atmospheric neutrinos, as well as neutrinos and muons from spallation sources. To achieve these objectives, a detector upgrade and a beam upgrade are required, with data-taking planned for the period 2029-2032 and beyond.

nucl-ex↗

arXiv2025

Multiplicity and net-electric charge fluctuations in central Ar+Sc interactions at 13A, 19A, 30A, 40A, 75A, and 150A GeV/c beam momenta measured by NA61/SHINE at the CERN SPS

This paper presents results on multiplicity fluctuations of positively and negatively charged hadrons as well as net-electric charge fluctuations measured in central Ar+Sc interactions at beam momenta 13A, 19A, 30A, 40A, 75A, and 150A GeV/c. The fluctuation analysis is one of the tools to search for the predicted critical point of strongly interacting matter. Results are corrected for the experimental biases and quantified using cumulant ratios. In most instances, multiplicity and net-charge distributions appear narrower than the corresponding Poisson or Skellam distributions. Cumulant ratios are compared with the EPOS1.99 model predictions, which provide a qualitative description that aligns with observations for positively and negatively charged particles. The obtained results are also compared to earlier NA61/SHINE results from inelastic p+p interactions in the same analysis acceptance.

nucl-ex↗

arXiv2025

Reconstruction of proton relative stopping power with a granular calorimeter detector model

Proton computed tomography (pCT) aims to facilitate precise dose planning for hadron therapy, a promising and effective method for cancer treatment. Hadron therapy utilizes protons and heavy ions to deliver well focused doses of radiation, leveraging the Bragg peak phenomenon to target tumors while sparing healthy tissues. The Bergen pCT Collaboration aims to develop a novel pCT scanner, and accompanying reconstruction algorithms to overcome current limitations. This paper focuses on advancing the track- and image reconstruction algorithms, thereby enhancing the precision of the dose planning and reducing side effects of hadron therapy. A neural network aided track reconstruction method is presented.

physics.comp-ph↗

arXiv2024

Performance of the electromagnetic and hadronic prototype segments of the ALICE Forward Calorimeter

We present the performance of a full-length prototype of the ALICE Forward Calorimeter (FoCal). The detector is composed of a silicon-tungsten electromagnetic sampling calorimeter with longitudinal and transverse segmentation (FoCal-E) of about 20$X_0$ and a hadronic copper-scintillating-fiber calorimeter (FoCal-H) of about 5$λ_{\rm int}$. The data were taken between 2021 and 2023 at the CERN PS and SPS beam lines with hadron (electron) beams up to energies of 350 (300) GeV. Regarding FoCal-E, we report a comprehensive analysis of its response to minimum ionizing particles across all pad layers. The longitudinal shower profile of electromagnetic showers is measured with a layer-wise segmentation of 1$X_0$. As a projection to the performance of the final detector in electromagnetic showers, we demonstrate linearity in the full energy range, and show that the energy resolution fulfills the requirements for the physics needs. Additionally, the performance to separate two-showers events was studied by quantifying the transverse shower width. Regarding FoCal-H, we report a detailed analysis of the response to hadron beams between 60 and 350 GeV. The results are compared to simulations obtained with a Geant4 model of the test beam setup, which in particular for FoCal-E are in good agreement with the data. The energy resolution of FoCal-E was found to be lower than 3% at energies larger than 100 GeV. The response of FoCal-H to hadron beams was found to be linear, albeit with a significant intercept that is about factor 2 larger than in simulations. Its resolution, which is non-Gaussian and generally larger than in simulations, was quantified using the FWHM, and decreases from about 16% at 100 GeV to about 11% at 350 GeV. The discrepancy to simulations, which is particularly evident at low hadron energies, needs to be further investigated.

physics.ins-det↗

arXiv2022

Performance of the Electromagnetic Pixel Calorimeter Prototype EPICAL-2

The first evaluation of an ultra-high granularity digital electromagnetic calorimeter prototype using 1.0-5.8 GeV/c electrons is presented. The $25\times10^6$ pixel detector consists of 24 layers of ALPIDE CMOS MAPS sensors, with a pitch of around 30~$μ$m, and has a depth of almost 20 radiation lengths of tungsten absorber. Ultra-thin cables allow for a very compact design. The properties that are critical for physics studies are measured: electromagnetic shower response, energy resolution and linearity. The stochastic energy resolution is comparable with the state-of-the art resolution for a Si-W calorimeter, with data described well by a simulation model using GEANT and Allpix$^2$. The performance achieved makes this technology a good candidate for use in the ALICE FoCal upgrade, and in general demonstrates the strong potential for future applications in high-energy physics.

physics.ins-det↗

arXiv2022

Results from the EPICAL-2 Ultra-High Granularity Electromagnetic Calorimeter Prototype

A prototype of a new type of calorimeter has been designed and constructed, based on a silicon-tungsten sampling design using pixel sensors with digital readout. It makes use of the Alpide MAPS sensor developed for the ALICE ITS upgrade. A binary readout is possible due to the pixel size of $\approx 30 \times 30 \, μ\mathrm{m}^2$. This prototype has been successfully tested with cosmic muons and with test beams at DESY and the CERN SPS. We report on performance results obtained at DESY, showing good energy resolution and linearity, and compare to detailed MC simulations. Also shown are preliminary results of the high-energy performance as measured at the SPS. The two-shower separation capabilities are discussed.

physics.ins-det↗

arXiv2022

Snowmass 2021/22 Letter of Interest: A Forward Calorimeter at the LHC

A forward electromagnetic and hadronic calorimeter (FoCal) was proposed as an upgrade to the ALICE experiment, to be installed during LS3 for data-taking in 2027--2029 at the LHC. The FoCal extends the scope of ALICE, which was designed for the comprehensive study of hot and dense partonic matter, by adding new capabilities to explore the small-$x$ parton structure of nucleons and nuclei. The primary objective of the FoCal is high-precision inclusive measurement of direct photons and jets, as well as coincident gamma-jet and jet-jet measurements, in pp and p--Pb collisions. These measurements by FoCal constitute an essential part of a comprehensive small-$x$ program at the LHC down to $x\sim10^{-6}$ and over a large range of $Q^2$ with a broad array of complementary probes, comprising -- in addition to the photon measurements by FoCal and LHCb -- Drell-Yan and open charm measurements planned by LHCb, as well as photon-induced reactions performed by all LHC experiments.

hep-ex↗

arXiv2022

Measurements of $Ξ^{-}$ and $\overlineΞ^{+}$ production in proton-proton interactions at $\sqrt{s_{NN}}$ = 17.3 GeV in the NA61/SHINE experiment

The production of $Ξ(1321)^{-}$ and $\overlineΞ(1321)^{+}$ hyperons in inelastic p+p interactions is studied in a fixed target experiment at a beam momentum of 158 GeV/textit{c}. Double differential distributions in rapidity y and transverse momentum $p_{T}$ are obtained from a sample of 33M inelastic events. They allow to extrapolate the spectra to full phase space and to determine the mean multiplicity of both $Ξ^{-}$ and $\overlineΞ^{+}$. The rapidity and transverse momentum spectra are compared to transport model predictions. The $Ξ^{-}$ mean multiplicity in inelastic p+p interactions at 158~\GeVc is used to quantify the strangeness enhancement in A+A collisions at the same centre-of-mass energy per nucleon pair.

nucl-ex↗

arXiv2021

Two-particle correlations in azimuthal angle and pseudorapidity in central $^7$Be+$^9$Be collisions at the CERN Super Proton Synchrotron

A measurement of charged hadron pair correlations in two-dimensional $ΔηΔϕ$ space is presented. The analysis is based on total 30 million central Be+Be collisions observed in the NA61/SHINE detector at the CERN SPS for incident beam momenta of 19$A$, 30$A$, 40$A$, 75$A$, and 150$A$ GeV/$c$. Measurements were carried out for unlike-sign and like-sign charge hadron pairs independently. The $C(Δη,Δϕ)$ correlation functions were compared with results from a similar analysis on p+p interactions at similar beam momenta per nucleon. General trends of the back-to-back correlations are similar in central Be+Be collisions and p+p interactions, but are suppressed in magnitude due to the increased combinatorial background. Predictions from the EPOS and UrQMD models are compared to the measurements. Evolution of an enhancement around $(Δη,Δϕ) = (0,0)$ with incident energy is observed in central Be+Be collisions. It is not predicted by both models and almost non-existing in proton-proton collisions at the same momentum per nucleon.

nucl-ex↗

arXiv2020

Design and Performance of a Silicon Tungsten Calorimeter Prototype Module and the Associated Readout

We describe the details of a silicon-tungsten prototype electromagnetic calorimeter module and associated readout electronics. Detector performance for this prototype has been measured in test beam experiments at the CERN PS and SPS accelerator facilities in 2015/16. The results are compared to those in Monte Carlo Geant4 simulations. This is the first real-world demonstration of the performance of a custom ASIC designed for fast, lower-power, high-granularity applications.

physics.ins-det↗

arXiv2020

Search for an exotic S=-2, Q=-2 baryon resonance in proton-proton interactions at $\sqrt{s_{NN}}$ = 17.3 GeV

Pentaquark states have been extensively investigated theoretically in the context of the constituent quark model. In this paper results of an experimental search for pentaquarks in the \Xim\pim, \Xim\pip, \Xip\pim and \Xip\pip invariant mass spectra in proton-proton interactions at $\sqrt{s}$=17.3~\GeV are presented. Previous possible evidence from the NA49 collaboration of the existence of a narrow \Xim\pim baryon resonance in p+p interactions is not confirmed with almost 10 times greater event statistics. The search was performed using the \NASixtyOne detector which reuses the main components of the NA49 apparatus. No signal was observed with either the selection cuts of NA49 or newly optimised cuts.

hep-ex↗

arXiv2020

Proton-proton interactions and onset of deconfinement

The NA61/SHINE experiment at the CERN SPS is performing a uniqe study of the phase diagram of strongly interacting matter by varying collision energy and nuclear mass number of colliding nuclei. In central Pb+Pb collisions the NA49 experiment found structures in the energy dependence of several observables in the CERN SPS energy range that had been predicted for the transition to a deconfined phase. New measurements of NA61/SHINE find intriguing similarities in p+p interactions for which no deconfinement transition is expected at SPS energies. Possible implications will be discussed.

hep-ex↗

arXiv2016

Production of $Λ$ hyperons in inelastic p+p interactions at 158 GeV/$c$

Inclusive production of $Λ$-hyperons was measured with the large acceptance NA61/SHINE spectrometer at the CERN SPS in inelastic p+p interactions at beam momentum of 158~\GeVc. Spectra of transverse momentum and transverse mass as well as distributions of rapidity and x$_{_F}$ are presented. The mean multiplicity was estimated to be $0.120\,\pm0.006\;(stat.)\,\pm 0.010\;(sys.)$. The results are compared with previous measurements and predictions of the EPOS, UrQMD and FRITIOF models.

hep-ex↗

arXiv2014

Measurement of negatively charged pion spectra in inelastic p+p interactions at $p_{lab}$ = 20, 31, 40, 80 and 158 GeV/c

We present experimental results on inclusive spectra and mean multiplicities of negatively charged pions produced in inelastic p+p interactions at incident projectile momenta of 20, 31, 40, 80 and 158 GeV/c ($\sqrt{s} = $ 6.3, 7.7, 8.8, 12.3 and 17.3 GeV, respectively). The measurements were performed using the large acceptance NA61/SHINE hadron spectrometer at the CERN Super Proton Synchrotron. Two-dimensional spectra are determined in terms of rapidity and transverse momentum. Their properties such as the width of rapidity distributions and the inverse slope parameter of transverse mass spectra are extracted and their collision energy dependences are presented. The results on inelastic p+p interactions are compared with the corresponding data on central Pb+Pb collisions measured by the NA49 experiment at the CERN SPS. The results presented in this paper are part of the NA61/SHINE ion program devoted to the study of the properties of the onset of deconfinement and search for the critical point of strongly interacting matter. They are required for interpretation of results on nucleus-nucleus and proton-nucleus collisions.

hep-ex↗

arXiv2012

Hadron calorimeter with MAPD readout in the NA61/SHINE experiment

The modular hadron calorimeter with micro-pixel avalanche photodiodes readout for the NA61/SHINE experiment at the CERN SPS is presented. The calorimeter consists of 44 independent modules with lead-scintillator sandwich structure. The light from the scintillator tiles is captured by and transported with WLS-fibers embedded in scintillator grooves. The construction provides a longitudinal segmentation of the module in 10 sections with independent MAPD readout. MAPDs with pixel density of $~10^{4}$/mm$^2$ ensure good linearity of calorimeter response in a wide dynamical range. The performance of the calorimeter prototype in a beam test is reported.

physics.ins-det↗