arXiv subjects

Daniel Bonilla Licea

Publications and source records attributed to Daniel Bonilla Licea.

At least 19 recordsLinked to original sources

arXiv2026

3D Euler-Angle Orientation Control for Two-Ray Fading Mitigation in Maritime Air-to-Sea Communications

Maritime Air-to-Sea links are dominated by a line-of-sight ray and a sea-surface reflected ray whose destructive combination produces deep fades. Existing mitigation strategies optimize Unmanned Aerial Vehicle position or trajectory but leave attitude unexploited. This paper treats the full three dimensional attitude as a physical-layer control variable that shapes the two-ray interference through antenna phase-center displacement. Under small-angle and far-field assumptions, the constructive-interference condition reduces to an affine constraint in the Euler angles and admits a closed-form family of minimum-norm attitude candidates. A differentiable soft-minimum rule yields a smooth reference tracked by a constrained Nonlinear Model Predictive Control controller on a fully-actuated tilting multirotor. The proposed scheme increases cumulative throughput by 11.4% over a pitch-only benchmark and 22.2% over a zero-orientation baseline, while preserving trajectory tracking and respecting actuator limits.

cs.RO↗

arXiv2026

Communications-Aware NMPC for Multi-Rotor Aerial Relay Networks Under Jamming Interference

Multi-Rotor Aerial Vehicles (MRAVs) are increasingly used in communication-dependent missions where connectivity loss directly compromises task execution. Existing anti-jamming strategies often decouple motion from communication, overlooking that link quality depends on vehicle attitude and antenna orientation. In coplanar platforms, ``tilt-to-translate'' maneuvers can inadvertently align antenna nulls with communication partners, causing severe degradation under interference. This paper presents a modular communications-aware control approach combining a high-level $\max$-$\min$ trajectory generator with an actuator-level Nonlinear Model Predictive Controller (NMPC). The trajectory layer optimizes the \emph{weakest link}---the link with the lower instantaneous Signal-to-Interference-plus-Noise Ratio, which bottlenecks the harmonic-mean end-to-end capacity---while the NMPC enforces vehicle dynamics, actuator limits, and antenna-alignment constraints. Antenna directionality is handled geometrically, avoiding explicit radiation-pattern parametrization. The method is evaluated in a relay scenario with an active jammer and compared across coplanar and tilted-propeller architectures. Results show a near two-order-of-magnitude increase in minimum end-to-end capacity, markedly reducing outage events, with moderate average-capacity gains. Tilted platforms preserve feasibility and link quality, whereas coplanar vehicles show recurrent degradation. These findings indicate that full actuation is a key enabler of reliable communications-aware operation under adversarial directional constraints.

cs.RO↗

arXiv2026

Orientation Matters: Learning Radiation Patterns of Multi-Rotor UAVs In-Flight to Enhance Communication Availability Modeling

The paper presents an approach for learning antenna Radiation Patterns (RPs) of a pair of heterogeneous quadrotor Uncrewed Aerial Vehicles (UAVs) by calibration flight data. RPs are modeled either as a Spherical Harmonics series or as a weighted average over inducing samples. Linear regression of polynomial coefficients enables decoupling of independent UAVs' RPs from the observed joint gain. A synchronized calibration trajectory provides training and testing samples in an obstacle-free anechoic altitude. Evaluation on a real-world dataset demonstrates the feasibility of learning both radiation patterns, achieving 4.56 dB RMS extrapolation error. The proposed RP learning and decoupling can be exploited in rapid recalibration upon payload changes, thereby enabling precise autonomous path planning and swarm control in real-world applications where setup changes are expected.

cs.RO↗

arXiv2026

Reflection-Based Relative Localization for Cooperative UAV Teams Using Active Markers

Reflections of active markers in the environment are a common source of ambiguity in onboard visual relative localization. This work presents a novel approach that exploits these typically unwanted reflections for onboard relative localization in heterogeneous multi-UAV teams. The method operates without prior knowledge of robot size or predefined marker configurations, remains independent of surface properties, and explicitly accounts for uncertainties caused by surface irregularities, including dynamic water surfaces relevant for marine deployments. We validated the approach in both indoor and outdoor experiments, demonstrating reliable operation across varying lighting conditions and achieving greater effective range (above 30 m) and accuracy than state-of-the-art methods. The video is available under the following link: https://youtu.be/y0zp8cIwkig.

cs.RO↗

arXiv2026

Semantic-Aware UAV Command and Control for Efficient IoT Data Collection

Unmanned Aerial Vehicles (UAVs) have emerged as a key enabler technology for data collection from Internet of Things (IoT) devices. However, effective data collection is challenged by resource constraints and the need for real-time decision-making. In this work, we propose a novel framework that integrates semantic communication with UAV command-and-control (C&C) to enable efficient image data collection from IoT devices. Each device uses Deep Joint Source-Channel Coding (DeepJSCC) to generate a compact semantic latent representation of its image to enable image reconstruction even under partial transmission. A base station (BS) controls the UAV's trajectory by transmitting acceleration commands. The objective is to maximize the average quality of reconstructed images by maintaining proximity to each device for a sufficient duration within a fixed time horizon. To address the challenging trade-off and account for delayed C&C signals, we model the problem as a Markov Decision Process and propose a Double Deep Q-Learning (DDQN)-based adaptive flight policy. Simulation results show that our approach outperforms baseline methods such as greedy and traveling salesman algorithms, in both device coverage and semantic reconstruction quality.

cs.RO↗

arXiv2026

Distributed UAV Formation Control Robust to Relative Pose Measurement Noise

A technique that allows a Formation-Enforcing Control (FEC) derived from graph rigidity theory to interface with a realistic relative localization system onboard lightweight Unmanned Aerial Vehicles (UAVs) is proposed in this paper. The proposed methodology enables reliable real-world deployment of UAVs in tight formations using relative localization systems burdened by non-negligible sensory noise. Such noise otherwise causes undesirable oscillations and drifts in sensor-based formations, and this effect is not sufficiently addressed in existing FEC algorithms. The proposed solution is based on decomposition of the gradient descent-based FEC command into interpretable elements, and then modifying these individually based on the estimated distribution of sensory noise, such that the resulting action limits the probability of overshooting the desired formation. The behavior of the system was analyzed and the practicality of the proposed solution was compared to pure gradient-descent in real-world experiments where it presented significantly better performance in terms of oscillations, deviation from the desired state

cs.RO↗

arXiv2025

Optical communication-based identification for multi-UAV systems: theory and practice

Mutual relative localization and identification is an important feature for the stabilization and navigation of multi-Unmanned Aerial Vehicle (UAV) systems. Camera-based communications technology, also referred to as Optical Camera Communications (OCC) in the literature, is a novel approach that could bring a valuable solution to such a complex task. In such system, the UAVs are equipped with LEDs that act as beacons and with cameras allowing them to locate the LEDs of other UAVs. Specific blinking sequences are assigned to the LEDs of each of the UAVs in order to uniquely identify them. This camera-based relative localization and identification system is immune to Radio Frequency (RF) electromagnetic interference and operates in Global Navigation satellite (GNSS) denied environments. In addition, since many UAVs are already equipped with cameras, the implementation of this system is inexpensive. In this article, we study in detail the capacity of this system and its limitations. Furthermore, we show how to construct blinking sequences for UAV LEDs in order to improve system performance. Finally, experimental results are presented to corroborate the analytical derivations.

eess.SP↗

arXiv2025

Towards agile multi-robot systems in the real world: Fast onboard tracking of active blinking markers for relative localization

A novel onboard tracking approach enabling vision-based relative localization and communication using Active blinking Marker Tracking (AMT) is introduced in this article. Active blinking markers on multi-robot team members improve the robustness of relative localization for aerial vehicles in tightly coupled multi-robot systems during real-world deployments, while also serving as a resilient communication system. Traditional tracking algorithms struggle with fast-moving blinking markers due to their intermittent appearance in camera frames and the complexity of associating multiple of these markers across consecutive frames. AMT addresses this by using weighted polynomial regression to predict the future appearance of active blinking markers while accounting for uncertainty in the prediction. In outdoor experiments, the AMT approach outperformed state-of-the-art methods in tracking density, accuracy, and complexity. The experimental validation of this novel tracking approach for relative localization and optical communication involved testing motion patterns motivated by our research on agile multi-robot deployment.

cs.RO↗

arXiv2025

Free-Space Optical Communication-Driven NMPC Framework for Multi-Rotor Aerial Vehicles in Structured Inspection Scenarios

This paper introduces a Nonlinear Model Predictive Control (NMPC) framework for communication-aware motion planning of Multi-Rotor Aerial Vehicles (MRAVs) using Free-Space Optical (FSO) links. The scenario involves MRAVs equipped with body-fixed optical transmitters and Unmanned Ground Vehicles (UGVs) acting as mobile relays, each outfitted with fixed conical Field-of-View (FoV) receivers. The controller integrates optical connectivity constraints into the NMPC formulation to ensure beam alignment and minimum link quality, while also enabling UGV tracking and obstacle avoidance. The method supports both coplanar and tilted MRAV configurations. MATLAB simulations demonstrate its feasibility and effectiveness.

cs.RO↗

arXiv2025

Robust Planning and Control of Omnidirectional MRAVs for Aerial Communications in Wireless Networks

A new class of Multi-Rotor Aerial Vehicles (MRAVs), known as omnidirectional MRAVs (o-MRAVs), has gained attention for their ability to independently control 3D position and orientation. This capability enhances robust planning and control in aerial communication networks, enabling more adaptive trajectory planning and precise antenna alignment without additional mechanical components. These features are particularly valuable in uncertain environments, where disturbances such as wind and interference affect communication stability. This paper examines o-MRAVs in the context of robust aerial network planning, comparing them with the more common under-actuated MRAVs (u-MRAVs). Key applications, including physical layer security, optical communications, and network densification, are highlighted, demonstrating the potential of o-MRAVs to improve reliability and efficiency in dynamic communication scenarios.

cs.RO↗

arXiv2025

Harnessing the Potential of Omnidirectional UAVs in RIS-Enabled Wireless Networks

Multirotor Aerial Vehicles (MRAVs) when integrated into wireless communication systems and equipped with a Reflective Intelligent Surface (RIS) enhance coverage and enable connectivity in obstructed areas. However, due to limited degrees of freedom (DoF), traditional under-actuated MRAVs with RIS are unable to control independently both the RIS orientation and their location, which significantly limits network performance. A new design, omnidirectional MRAV (o-MRAV), is introduced to address this issue. In this paper, an o-MRAV is deployed to assist a terrestrial base station in providing connectivity to obstructed users. Our objective is to maximize the minimum data rate among users by optimizing the o-MRAV's orientation, location, and RIS phase shift. To solve this challenging problem, we first smooth the objective function and then apply the Parallel Successive Convex Approximation (PSCA) technique to find efficient solutions. Our simulation results show significant improvements of 28% and 14% in terms of minimum and average data rates, respectively, for the o-MRAVs compared to traditional u-MRAVs.

cs.NI↗

arXiv2024

Reshaping UAV-Enabled Communications with Omnidirectional Multi-Rotor Aerial Vehicles

A new class of Multi-Rotor Aerial Vehicles (MRAVs), known as omnidirectional MRAVs (o-MRAVs), has attracted significant interest in the robotics community. These MRAVs have the unique capability of independently controlling their 3D position and 3D orientation. In the context of aerial communication networks, this translates into the ability to control the position and orientation of the antenna mounted on the MRAV without any additional devices tasked for antenna orientation. This additional Degrees of Freedom (DoF) adds a new dimension to aerial communication systems, creating various research opportunities in communications-aware trajectory planning and positioning. This paper presents this new class of MRAVs and discusses use cases in areas such as physical layer security and optical communications. Furthermore, the benefits of these MRAVs are illustrated with realistic simulation scenarios. Finally, new research problems and opportunities introduced by this advanced robotics technology are discussed.

cs.RO↗

arXiv2024

Harnessing the Potential of Omnidirectional Multi-Rotor Aerial Vehicles in Cooperative Jamming Against Eavesdropping

Recent research in communications-aware robotics has been propelled by advancements in 5G and emerging 6G technologies. This field now includes the integration of Multi-Rotor Aerial Vehicles (MRAVs) into cellular networks, with a specific focus on under-actuated MRAVs. These vehicles face challenges in independently controlling position and orientation due to their limited control inputs, which adversely affects communication metrics such as Signal-to-Noise Ratio. In response, a newer class of omnidirectional MRAVs has been developed, which can control both position and orientation simultaneously by tilting their propellers. However, exploiting this capability fully requires sophisticated motion planning techniques. This paper presents a novel application of omnidirectional MRAVs designed to enhance communication security and thwart eavesdropping. It proposes a strategy where one MRAV functions as an aerial Base Station, while another acts as a friendly jammer to secure communications. This study is the first to apply such a strategy to MRAVs in scenarios involving eavesdroppers.

cs.RO↗

arXiv2024

PACNav: Enhancing Collective Navigation for UAV Swarms in Communication-Challenged Environments

This article presents Persistence Administered Collective Navigation (PACNav) as an approach for achieving decentralized collective navigation of Unmanned Aerial Vehicle (UAV) swarms. The technique is inspired by the flocking and collective navigation behavior observed in natural swarms, such as cattle herds, bird flocks, and even large groups of humans. PACNav relies solely on local observations of relative positions of UAVs, making it suitable for large swarms deprived of communication capabilities and external localization systems. We introduce the novel concepts of path persistence and path similarity, which allow each swarm member to analyze the motion of others. PACNav is grounded on two main principles: (1) UAVs with little variation in motion direction exhibit high path persistence and are considered reliable leaders by other UAVs; (2) groups of UAVs that move in a similar direction demonstrate high path similarity, and such groups are assumed to contain a reliable leader. The proposed approach also incorporates a reactive collision avoidance mechanism to prevent collisions with swarm members and environmental obstacles. The method is validated through simulated and real-world experiments conducted in a natural forest.

cs.RO↗

arXiv2024

When Robotics Meets Wireless Communications: An Introductory Tutorial

The importance of ground Mobile Robots (MRs) and Unmanned Aerial Vehicles (UAVs) within the research community, industry, and society is growing fast. Many of these agents are nowadays equipped with communication systems that are, in some cases, essential to successfully achieve certain tasks. In this context, we have begun to witness the development of a new interdisciplinary research field at the intersection of robotics and communications. This research field has been boosted by the intention of integrating UAVs within the 5G and 6G communication networks. This research will undoubtedly lead to many important applications in the near future. Nevertheless, one of the main obstacles to the development of this research area is that most researchers address these problems by oversimplifying either the robotics or the communications aspect. This impedes the ability of reaching the full potential of this new interdisciplinary research area. In this tutorial, we present some of the modelling tools necessary to address problems involving both robotics and communication from an interdisciplinary perspective. As an illustrative example of such problems, we focus in this tutorial on the issue of communication-aware trajectory planning.

cs.RO↗

arXiv2024

Omnidirectional Multi-Rotor Aerial Vehicle Pose Optimization: A Novel Approach to Physical Layer Security

The integration of Multi-Rotor Aerial Vehicles (MRAVs) into 5G and 6G networks enhances coverage, connectivity, and congestion management. This fosters communication-aware robotics, exploring the interplay between robotics and communications, but also makes the MRAVs susceptible to malicious attacks, such as jamming. One traditional approach to counter these attacks is the use of beamforming on the MRAVs to apply physical layer security techniques. In this paper, we explore pose optimization as an alternative approach to countering jamming attacks on MRAVs. This technique is intended for omnidirectional MRAVs, which are drones capable of independently controlling both their position and orientation, as opposed to the more common underactuated MRAVs whose orientation cannot be controlled independently of their position. In this paper, we consider an omnidirectional MRAV serving as a Base Station (BS) for legitimate ground nodes, under attack by a malicious jammer. We optimize the MRAV pose (i.e., position and orientation) to maximize the minimum Signal-to-Interference-plus-Noise Ratio (SINR) over all legitimate nodes.

cs.RO↗

arXiv2023

MRS Drone: A Modular Platform for Real-World Deployment of Aerial Multi-Robot Systems

This paper presents a modular autonomous Unmanned Aerial Vehicle (UAV) platform called the Multi-robot Systems (MRS) Drone that can be used in a large range of indoor and outdoor applications. The MRS Drone features unique modularity with respect to changes in actuators, frames, and sensory configuration. As the name suggests, the platform is specially tailored for deployment within a MRS group. The MRS Drone contributes to the state-of-the-art of UAV platforms by allowing smooth real-world deployment of multiple aerial robots, as well as by outperforming other platforms with its modularity. For real-world multi-robot deployment in various applications, the platform is easy to both assemble and modify. Moreover, it is accompanied by a realistic simulator to enable safe pre-flight testing and a smooth transition to complex real-world experiments. In this manuscript, we present mechanical and electrical designs, software architecture, and technical specifications to build a fully autonomous multi UAV system. Finally, we demonstrate the full capabilities and the unique modularity of the MRS Drone in various real-world applications that required a diverse range of platform configurations.

cs.RO↗

arXiv2023

Communications-Aware Robotics: Challenges and Opportunities

The use of Unmanned Ground Vehicles (UGVs) and Unmanned Aerial Vehicles (UAVs) has seen significant growth in the research community, industry, and society. Many of these agents are equipped with communication systems that are essential for completing certain tasks successfully. This has led to the emergence of a new interdisciplinary field at the intersection of robotics and communications, which has been further driven by the integration of UAVs into 5G and 6G communication networks. However, one of the main challenges in this research area is how many researchers tend to oversimplify either the robotics or the communications aspects, hindering the full potential of this new interdisciplinary field. In this paper, we present some of the necessary modeling tools for addressing these problems from both a robotics and communications perspective, using the UAV communications relay as an example.

cs.RO↗