arXiv subjects

Daniel F. Santavicca

Publications and source records attributed to Daniel F. Santavicca.

15 recordsLinked to original sources

arXiv2024

Optimization of Superconducting Niobium Nitride Thin Films via High-Power Impulse Magnetron Sputtering

We report a systematic comparison of niobium nitride thin films deposited on oxidized silicon substrates by reactive DC magnetron sputtering and reactive high-power impulse magnetron sputtering (HiPIMS). After determining the nitrogen gas concentration that produces the highest superconducting critical temperature for each process, we characterize the dependence of the critical temperature on film thickness. The optimal nitrogen concentration is higher for HiPIMS than for DC sputtering, and HiPIMS produces higher critical temperatures for all thicknesses studied. We attribute this to the HiPIMS process enabling the films to get closer to optimal stoichiometry before beginning to form a hexagonal crystal phase that reduces the critical temperature, along with the extra kinetic energy in the HiPIMS process improving crystallinity. We also study the ability to increase the critical temperature of the HiPIMS films through the use of an aluminum nitride buffer layer and substrate heating.

cond-mat.supr-con↗

arXiv2021

50 Ohm Transmission Lines with Extreme Wavelength Compression Based on Superconducting Nanowires on High-Permittivity Substrates

We demonstrate impedance-matched low-loss transmission lines with a signal wavelength more than 150 times smaller than the free space wavelength using superconducting nanowires on high permittivity substrates. A niobium nitride thin film is patterned in a coplanar waveguide (CPW) transmission line geometry on a bilayer substrate consisting of 100 nm of epitaxial strontium titanate on high-resitivity silicon. The use of strontium titanate on silicon enables wafer-scale fabrication and maximizes process compatibility. It also makes it possible to realize a $50$ $Ω$ characteristic impedance across a wide range of CPW widths, from the nanoscale to the macroscale. We fabricated and characterized an approximately $50$ $Ω$ CPW device with two half-wave stub resonators. Comparing the measured transmission coefficient to numerical simulations, we determine that the strontium titanate film has a dielectric constant of $1.1 \times 10^3$ and a loss tangent of not more than 0.009. To facilitate the design of distributed microwave devices based on this type of material system, we describe an analytical model of the CPW properties that gives good agreement with both measurements and simulations.

cond-mat.supr-con↗

arXiv2020

A compact and tunable forward coupler based on high-impedance superconducting nanowires

Developing compact, low-dissipation, cryogenic-compatible microwave electronics is essential for scaling up low-temperature quantum computing systems. In this paper, we demonstrate an ultra-compact microwave directional forward coupler based on high-impedance slow-wave superconducting-nanowire transmission lines. The coupling section of the fabricated device has a footprint of $416\,\mathrm{μm^2}$. At 4.753 GHz, the input signal couples equally to the through port and forward-coupling port (50:50) at $-6.7\,\mathrm{dB}$ with $-13.5\,\mathrm{dB}$ isolation. The coupling ratio can be controlled with DC bias current or temperature by exploiting the dependence of the kinetic inductance on these quantities. The material and fabrication-process are suitable for direct integration with superconducting circuits, providing a practical solution to the signal distribution bottlenecks in developing large-scale quantum computers.

physics.app-ph↗

arXiv2018

Superconducting nanowire single-photon detector with integrated impedance-matching taper

Conventional readout of a superconducting nanowire single-photon detector (SNSPD) sets an upper bound on the output voltage to be the product of the bias current and the load impedance, $I_\mathrm{B}\times Z_\mathrm{load}$, where $Z_\mathrm{load}$ is limited to 50 $Ω$ in standard r.f. electronics. Here, we break this limit by interfacing the 50 $Ω$ load and the SNSPD using an integrated superconducting transmission line taper. The taper is a transformer that effectively loads the SNSPD with high impedance without latching. It increases the amplitude of the detector output while preserving the fast rising edge. Using a taper with a starting width of 500 nm, we experimentally observed a 3.6$\times$ higher pulse amplitude, 3.7$\times$ faster slew rate, and 25.1 ps smaller timing jitter. The results match our numerical simulation, which incorporates both the hotspot dynamics in the SNSPD and the distributed nature in the transmission line taper. The taper studied here may become a useful tool to interface high-impedance superconducting nanowire devices to conventional low-impedance circuits.

physics.ins-det↗

arXiv2018

A distributed electrical model for superconducting nanowire single photon detectors

To analyze the switching dynamics and output performance of a superconducting nanowire single photon detector (SNSPD), the nanowire is usually modelled as an inductor in series with a time-varying resistor induced by absorption of a photon. Our recent experimental results show that, due to the effect of kinetic inductance, for a SNSPD made of a nanowire of sufficient length, its geometry length can be comparable to or even longer than the effective wavelength of frequencies contained in the output pulse. In other words, a superconducting nanowire can behave as a distributed transmission line so that the readout pulse depends on the photon detection location and the transmission line properties of the nanowire. Here, we develop a distributed model for a superconducting nanowire and apply it to simulate the output performance of a long nanowire designed into a coplanar waveguide. We compare this coplanar waveguide geometry to a conventional meander nanowire geometry. The simulation results agree well with our experimental observations. With this distributed model, we discussed the importance of microwave design of a nanowire and how impedance matching can affect the output pulse shape. We also discuss how the distributed model affects the growth and decay of the photon-triggered resistive hotspot.

physics.app-ph↗

arXiv2016

A Single-Photon Imager Based on Microwave Plasmonic Superconducting Nanowire

Detecting spatial and temporal information of individual photons by using single-photon-detector (SPD) arrays is critical to applications in spectroscopy, communication, biological imaging, astronomical observation, and quantum-information processing. Among the current SPDs1,detectors based on superconducting nanowires have outstanding performance2, but are limited in their ability to be integrated into large scale arrays due to the engineering difficulty of high-bandwidth cryogenic electronic readout3-8. Here, we address this problem by demonstrating a scalable single-photon imager using a single continuous photon-sensitive superconducting nanowire microwave-plasmon transmission line. By appropriately designing the nanowire's local electromagnetic environment so that the nanowire guides microwave plasmons, the propagating voltages signals generated by a photon-detection event were slowed down to ~ 2% of the speed of light. As a result, the time difference between arrivals of the signals at the two ends of the nanowire naturally encoded the position and time of absorption of the photon. Thus, with only two readout lines, we demonstrated that a 19.7-mm-long nanowire meandered across an area of 286 μm * 193 μm was capable of resolving ~590 effective pixels while simultaneously recording the arrival times of photons with a temporal resolution of 50 ps. The nanowire imager presents a scalable approach to realizing high-resolution photon imaging in time and space.

physics.optics↗

arXiv2016

Microwave dynamics of high aspect ratio superconducting nanowires studied using self-resonance

We study the microwave impedance of extremely high aspect ratio (length/width ~ 5,000) superconducting niobium nitride nanowires. The nanowires are fabricated in a compact meander geometry that is in series with the center conductor of a 50 ohm coplanar waveguide transmission line. The transmission coefficient of the sample is measured up to 20 GHz. At high frequency, a peak in the transmission coefficient is seen. Numerical simulations show that this is a half-wave resonance along the length of the nanowire, where the nanowire acts as a high impedance, slow wave transmission line. This resonance sets the upper frequency limit for these nanowires as inductive elements. Fitting simulations to the measured resonance enables a precise determination of the nanowire's complex sheet impedance at the resonance frequency. The real part is a measure of dissipation, while the imaginary part is dominated by kinetic inductance. We characterize the dependence of the sheet resistance and sheet inductance on both temperature and current and compare the results to recent theoretical predictions for disordered superconductors. These results can aid in the understanding of high frequency devices based on superconducting nanowires. They may also lead to the development of novel superconducting devices such as ultra-compact resonators and slow-wave structures.

cond-mat.supr-con↗

arXiv2012

Energy-resolved detection of single infrared photons with λ = 8 μm using a superconducting microbolometer

We report on the detection of single photons with λ = 8 μm using a superconducting hot-electron microbolometer. The sensing element is a titanium transition-edge sensor with a volume ~ 0.1 μm^3 fabricated on a silicon substrate. Poisson photon counting statistics including simultaneous detection of 3 photons was observed. The width of the photon-number peaks was 0.11 eV, 70% of the photon energy, at 50-100 mK. This achieved energy resolution is one of the best figures reported so far for superconducting devices. Such devices can be suitable for single photon calorimetric spectroscopy throughout the mid-infrared and even the far-infrared.

physics.ins-det↗

arXiv2012

Terahertz detection mechanism and contact capacitance of individual metallic single-walled carbon nanotubes

We characterize the terahertz detection mechanism in antenna-coupled metallic single-walled carbon nanotubes. At low temperature, 4.2 K, a peak in the low-frequency differential resistance is observed at zero bias current due to non-Ohmic contacts. This electrical contact nonlinearity gives rise to the measured terahertz response. By modeling each nanotube contact as a nonlinear resistor in parallel with a capacitor, we determine an upper bound for the value of the contact capacitance that is smaller than previous experimental estimates. The small magnitude of this contact capacitance has favorable implications for the use of carbon nanotubes in high-frequency device applications.

cond-mat.mes-hall↗

arXiv2012

Proposal for a GHz count rate near-IR single-photon detector based on a nanoscale superconducting transition edge sensor

We describe a superconducting transition edge sensor based on a nanoscale niobium detector element. This device is predicted to be capable of energy-resolved near-IR single-photon detection with a GHz count rate. The increased speed and sensitivity of this device compared to traditional transition edge sensors result from the very small electronic heat capacity of the nanoscale detector element. In the present work, we calculate the predicted thermal response time and energy resolution. We also discuss approaches for achieving efficient optical coupling to the sub-wavelength detector element using a resonant near-IR antenna.

physics.ins-det↗

arXiv2011

Bolometric and non-bolometric radio frequency detection in a metallic single-walled carbon nanotube

We characterize radio frequency detection in a high-quality metallic single-walled carbon nanotube. At a bath temperature of 77 K, only bolometric (thermal) detection is seen. At a bath temperature of 4.2 K and low bias current, the response is due instead to the electrical nonlinearity of the non-ohmic contacts. At higher bias currents, the contacts recover ohmic behavior and the observed response agrees well with the calculated bolometric responsivity. The bolometric response is expected to operate at terahertz frequencies, and we discuss some of the practical issues associated with developing high frequency detectors based on carbon nanotubes.

cond-mat.mes-hall↗

arXiv2010

Energy loss of the electron system in individual single-walled carbon nanotubes

We characterize the energy loss of the non-equilibrium electron system in individual metallic single-walled carbon nanotubes at low temperature. Using Johnson noise thermometry, we demonstrate that, for a nanotube with ohmic contacts, the dc resistance at finite bias current directly reflects the average electron temperature. This enables a straightforward determination of the thermal conductance associated with cooling of the nanotube electron system. In analyzing the temperature- and length-dependence of the thermal conductance, we consider contributions from acoustic phonon emission, optical phonon emission, and hot electron outdiffusion.

cond-mat.mes-hall↗

arXiv2010

Reset dynamics and latching in niobium superconducting nanowire single-photon detectors

We study the reset dynamics of niobium (Nb) superconducting nanowire single-photon detectors (SNSPDs) using experimental measurements and numerical simulations. The numerical simulations of the detection dynamics agree well with experimental measurements, using independently determined parameters in the simulations. We find that if the photon-induced hotspot cools too slowly, the device will latch into a dc resistive state. To avoid latching, the time for the hotspot to cool must be short compared to the inductive time constant that governs the resetting of the current in the device after hotspot formation. From simulations of the energy relaxation process, we find that the hotspot cooling time is determined primarily by the temperature-dependent electron-phonon inelastic time. Latching prevents reset and precludes subsequent photon detection. Fast resetting to the superconducting state is therefore essential, and we demonstrate experimentally how this is achieved.

cond-mat.supr-con↗

arXiv2009

Niobium superconducting nanowire single-photon detectors

We investigate the performance of superconducting nanowire photon detectors fabricated from ultra-thin Nb. A direct comparison is made between these detectors and similar nanowire detectors fabricated from NbN. We find that Nb detectors are significantly more susceptible than NbN to thermal instability (latching) at high bias. We show that the devices can be stabilized by reducing the input resistance of the readout. Nb detectors optimized in this way are shown to have approximately 2/3 the reset time of similar large-active-area NbN detectors of the same geometry, with approximately 6% detection efficiency for single photons at 470 nm.

cond-mat.supr-con↗

arXiv2006

Hot Electron Bolometer Development for a Submillimeter Heterodyne Array Camera

We are developing Nb diffusion-cooled Hot Electron Bolometers (HEBs) for a large-format array submillimeter camera. We have fabricated Nb HEBs using a new angle deposition process. We have characterized these devices using heterodyne mixing at 20 GHz. We also report on optimizations in the fabrication process that improve device performance.

cond-mat.other↗