arXiv subjects

Daniel S. Drew

Publications and source records attributed to Daniel S. Drew.

10 recordsLinked to original sources

arXiv2026

Hoverflie: An empirical investigation of rotor shrouds to transform micro air vehicles into multi-modal hovercraft

Small rotorcraft intended for use indoors or around the built environment have extremely limited flight duration. This paper presents the design and experimental characterization of a custom shroud system that transforms a Crazyflie 2.1 micro air vehicle into a multi-modal robot capable of operating as a high-efficiency hovercraft or a free-flying drone. A custom experimental platform was developed for precise control of hover height and rotor duty cycle, and automated data logging of lift forces. Parametric testing of duct, intake, and nozzle geometries was performed to investigate the impact of shroud configuration on in-ground-effect and free-flight performance. An empirical model is developed which, unlike typical models for ground effect in rotorcraft, captures the suckdown effect that reduces force at intermediate height. It is shown that, through proper design of the shroud, beneficial ground effects can be increased while diminishing negative effects both close to the ground and in free flight. An optimized configuration exhibited nearly three times higher in-ground-effect force while maintaining comparable out-of-ground-effect aerodynamic thrust, although the added shroud mass reduces free-flight control authority. Lightweight shrouds are manufactured using thin-film thermoformed components, and total single-charge flight time is shown to increase by 60% in-ground-effect while decreasing by only 30% in free-flight as compared to the stock drone. Finally, controlled flight in the air, hovering close to the ground, and hover-to-flight transitions are demonstrated using a simple mode-switching controller, with tracking errors reported to quantify performance. This work provides an experimentally-validated and easily adoptable foundation for future research into lightweight ground-effect vehicles and hybrid drone-hovercraft systems.

cs.RO↗

arXiv2026

Design and Flight of an Ion-propelled Micro Hovercraft Leveraging Ground Proximity Effects

Electroaerodynamic propulsion is compelling for use in micro air vehicles due to its silent and solid-state nature, but its limited efficiency has thus far precluded a path towards power-autonomous flight. Recent work has shown that thrust density and efficiency for small-scale atmospheric ion thrusters can be vastly increased when operating close to a ground plane. Here, we explore the design space of centimeter-scale hovercraft, which can leverage this ground effect for low-altitude flight. We first perform an empirical investigation, characterizing the performance benefits and trade-offs for different geometries and configurations of passive hovercraft skirts, then use the results to fabricate a viable point design. We demonstrate a palm-sized hovercraft that, while tethered to an external power source, can fly for extended periods, withstand dozens of takeoff and landing cycles, passively stabilize to reject significant mechanical disturbances, and generate practically zero audible noise signature. The measured thrust efficiency of 16 mN/W and additional payload capacity of almost 1.5 grams above the vehicle's self mass of about 1.6 grams exceeds any similarly sized electroaerodynamically propelled robot by an order of magnitude. This is the first time an ion-propelled micro hovercraft has been shown in the open literature, and our work points the way towards an entirely new class of robot.

cs.RO↗

arXiv2026

Jet impingement cooling with multi-stage ducted electroaerodynamic actuators

Modern high-performance mobile electronics impose extreme constraints on thermal management, and traditional cooling methods often fail to meet requirements for power density, form factor, and durability. Jet impingement cooling offers a compelling solution but is typically hindered by the need for bulky ancillary hardware. Here, we demonstrate that compact arrays of reduced-scale electroaerodynamic (EAD) plasma actuators, which are silent, solid-state devices with no moving parts, can be used for direct jet impingement cooling of electronics. The main contribution is the first rigorous experimental demonstration and system-level validation of multi-stage, ducted electroaerodynamic jet arrays as a compact, fan-replacement impingement cooling solution for mobile electronics. We characterize the performance of both single- and multi-stage ducted actuators, including thermographic analysis of heat transfer coefficients and spatial cooling profiles. We also quantify the relationship between actuator stage count and cooling efficiency, showing that increasing the number of ion acceleration stages enhances jet velocity and heat transfer performance at a reduced efficiency. The actuators are then assembled into an array and directly compared to a conventional fan with similar coverage area, showing competitive performance at a fraction of the volume, weight, and power. Finally, we integrate the array onto a commercial edge AI system and show that thermal regulation during extended inference workloads matches that of a stock fan, without any moving mechanical components or noise. These results confirm that multi-stage EAD jet arrays are not only viable but advantageous for thermal management in mobile and high-performance systems, paving the way toward silent and miniaturized solid-state cooling solutions.

eess.SY↗

arXiv2025

Discovery and Deployment of Emergent Robot Swarm Behaviors via Representation Learning and Real2Sim2Real Transfer

Given a swarm of limited-capability robots, we seek to automatically discover the set of possible emergent behaviors. Prior approaches to behavior discovery rely on human feedback or hand-crafted behavior metrics to represent and evolve behaviors and only discover behaviors in simulation, without testing or considering the deployment of these new behaviors on real robot swarms. In this work, we present Real2Sim2Real Behavior Discovery via Self-Supervised Representation Learning, which combines representation learning and novelty search to discover possible emergent behaviors automatically in simulation and enable direct controller transfer to real robots. First, we evaluate our method in simulation and show that our proposed self-supervised representation learning approach outperforms previous hand-crafted metrics by more accurately representing the space of possible emergent behaviors. Then, we address the reality gap by incorporating recent work in sim2real transfer for swarms into our lightweight simulator design, enabling direct robot deployment of all behaviors discovered in simulation on an open-source and low-cost robot platform.

cs.RO↗

arXiv2024

Empirical Study of Ceiling Proximity Effects and Electrostatic Adhesion for Small-scale Electroaerodynamic Thrusters

Electroaerodynamic propulsion, where force is produced via the momentum-transferring collisions between accelerated ions and neutral air molecules, is a promising alternative mechanism for flight at the micro air vehicle scale due to its silent and solid-state nature. Its relatively low efficiency, however, has thus far precluded its use in a power-autonomous vehicle; leveraging the efficiency benefits of operation close to a fixed surface is a potential solution. While proximity effects like the ground and ceiling effects have been well-investigated for rotorcraft and flapping wing micro air vehicles, they have not been for electroaerodynamically-propelled fliers. In this work, we investigate the change in performance when centimeter-scale thrusters are operated close to a "ceiling" plane about the inlet. We show a surprising and, until now, unreported effect; a major electrostatic attractive component, analogous to electroadhesive pressure but instead mediated by a stable atmospheric plasma. The isolated electrostatic and fluid dynamic components of the ceiling effect are shown for different distances from the plane and for different materials. We further show that a flange attached to the inlet can vastly increase both components of force. A peak efficiency improvement of 600% is shown close to the ceiling. This work points the way towards effective use of the ceiling effect for power autonomous vehicles, extending flight duration, or as a perching mechanism.

cs.RO↗

arXiv2023

Empirical Study of Ground Proximity Effects for Small-scale Electroaerodynamic Thrusters

Electroaerodynamic (EAD) propulsion, where thrust is produced by collisions between electrostatically-accelerated ions and neutral air, is a potentially transformative method for indoor flight owing to its silent and solid-state nature. Like rotors, EAD thrusters exhibit changes in performance based on proximity to surfaces. Unlike rotors, they have no fragile and quickly spinning parts that have to avoid those surfaces; taking advantage of the efficiency benefits from proximity effects may be a route towards longer-duration indoor operation of ion-propelled fliers. This work presents the first empirical study of ground proximity effects for EAD propulsors, both individually and as quad-thruster arrays. It focuses on multi-stage ducted centimeter-scale actuators suitable for use on small robots envisioned for deployment in human-proximal and indoor environments. Three specific effects (ground, suckdown, and fountain lift), each occurring with a different magnitude at a different spacing from the ground plane, are investigated and shown to have strong dependencies on geometric parameters including thruster-to-thruster spacing, thruster protrusion from the fuselage, and inclusion of flanges or strakes. Peak thrust enhancement ranging from 300 to 600% is found for certain configurations operated in close proximity (0.2 mm) to the ground plane and as much as a 20% increase is measured even when operated centimeters away.

cs.RO↗

arXiv2023

High Aspect Ratio Multi-stage Ducted Electroaerodynamic Thrusters for Micro Air Vehicle Propulsion

Electroaerodynamic propulsion, where force is produced through collisions between electrostatically accelerated ions and neutral air molecules, is an attractive alternative to propeller- and flapping wing-based methods for micro air vehicle (MAV) flight due to its silent and solid-state nature. One major barrier to adoption is its limited thrust efficiency at useful disk loading levels. Ducted actuators comprising multiple serially-integrated acceleration stages are a potential solution, allowing individual stages to operate at higher efficiency while maintaining a useful total thrust, and potentially improving efficiency through various aerodynamic and fluid dynamic mechanisms. In this work, we investigate the effects of duct and emitter electrode geometries on actuator performance, then show how a combination of increasing cross-sectional aspect ratio and serial integration of multiple stages can be used to produce overall thrust densities comparable to commercial propulsors. An optimized five-stage device attains a thrust density of about 18 N/m$^2$ at a thrust efficiency of about 2 mN/W, among the highest values ever measured at this scale. We further show how this type of thruster can be integrated under the wings of a MAV-scale fixed wing platform, pointing towards future use as a distributed propulsion system.

cs.RO↗

arXiv2023

Toward a Millimeter-Scale Tendon-Driven Continuum Wrist with Integrated Gripper for Microsurgical Applications

Microsurgery is a particularly impactful yet challenging form of surgery. Robot assisted microsurgery has the potential to improve surgical dexterity and enable precise operation on such small scales in ways not previously possible. Intraocular microsurgery is a particularly challenging domain in part due to the lack of dexterity that is achievable with rigid instruments inserted through the eye. In this work, we present a new design for a millimeter-scale, dexterous wrist intended for microsurgery applications. The wrist is created via a state-of-the-art two-photon-polymerization (2PP) microfabrication technique, enabling the wrist to be constructed of flexible material with complex internal geometries and critical features at the micron-scale. The wrist features a square cross section with side length of 1.25 mm and total length of 3.75 mm. The wrist has three tendons routed down its length which, when actuated by small-scale linear actuators, enable bending in any plane. We present an integrated gripper actuated by a fourth tendon routed down the center of the robot. We evaluate the wrist and gripper by characterizing its bend-angle. We achieve more than 90 degrees bending in both axes. We demonstrate out of plane bending as well as the robot's ability to grip while actuated. Our integrated gripper/tendon-driven continuum robot design and meso-scale assembly techniques have the potential to enable small-scale wrists with more dexterity than has been previously demonstrated. Such a wrist could improve surgeon capabilities during teleoperation with the potential to improve patient outcomes in a variety of surgical applications, including intraocular surgery.

cs.RO↗

arXiv2021

High Force Density Multi-Stage Electrohydrodynamic Jets Using Folded Laser Microfabricated Electrodes

The electrohydrodynamic (EHD) force produced by ions ejected from a corona plasma is a solid state, silent mechanism for accelerating air, useful for applications ranging from electronics cooling to flying microrobots. This paper presents the theoretical motivation and the first implementation of a multi-stage, highly miniaturized EHD device, which can provide both improved absolute power output and power density as compared to single-stage devices. A laser microfabricated, folded electrode design reduces component count and assembly time. Data from one, two, and three-stage devices demonstrates a near linear scaling of output force with stage count, indicating inter-stage ducting successfully reduces losses. Device lifetime is assessed to validate the use of stainless-steel emission electrodes. Areal thrust, force density, and volumetric power density for the three-stage device are among the highest ever measured from an EHD actuator.

eess.SY↗

arXiv2019

Low Level Control of a Quadrotor with Deep Model-Based Reinforcement Learning

Designing effective low-level robot controllers often entail platform-specific implementations that require manual heuristic parameter tuning, significant system knowledge, or long design times. With the rising number of robotic and mechatronic systems deployed across areas ranging from industrial automation to intelligent toys, the need for a general approach to generating low-level controllers is increasing. To address the challenge of rapidly generating low-level controllers, we argue for using model-based reinforcement learning (MBRL) trained on relatively small amounts of automatically generated (i.e., without system simulation) data. In this paper, we explore the capabilities of MBRL on a Crazyflie centimeter-scale quadrotor with rapid dynamics to predict and control at <50Hz. To our knowledge, this is the first use of MBRL for controlled hover of a quadrotor using only on-board sensors, direct motor input signals, and no initial dynamics knowledge. Our controller leverages rapid simulation of a neural network forward dynamics model on a GPU-enabled base station, which then transmits the best current action to the quadrotor firmware via radio. In our experiments, the quadrotor achieved hovering capability of up to 6 seconds with 3 minutes of experimental training data.

cs.RO↗