Searcharxiv⌕ Search

arXiv subjects

Daoud Mezzane

Publications and source records attributed to Daoud Mezzane.

At least 19 recordsLinked to original sources
arXiv2026

Improvement of piezocatalytic performance of Na0.5Bi0.5TiO3 perovskite using K doping for efficient Rhodamine B degradation

Piezocatalysis, based on the piezoelectric properties of catalysts, breaks down the barrier between mechanical energy and chemical energy. It describes the use of charges induced by piezoelectricity to assist typical chemical processes while harvesting various forms of mechanical green energy. The performance of piezocatalysis is predominantly governed by the piezoelectric properties of materials. The main aim of this work is to evaluate and analyze the potential of potassium doped sodium bismuth titanate Na0.5-xKxBi0.5TiO3 abbreviated as NKxBT (0, 0.15, 0.20, and 0.25), as a piezocatalyst in the degradation of the organic dye Rhodamine B RhB under ultrasonic vibration. The synthesis of NKxBT nanopowders was conducted using the sol-gel autocombustion method. Coupled structural analysis reveals the presence of an intermediate Morphotropic Phase Boundary (MPB, where two phases coexist) in the optimal NK15BT composition. The piezocatalytic degradation results showed a total piezo-degradation in only 90 min and a rate constant 8 times higher than the undoped NK0BT. The enhanced piezocatalytic activity results from a synergistic effect of MPB presence, reduced particle size, optimal bandgap and high lattice strain. The NK15BT sample also demonstrated good reusability and good mineralization.

cond-mat.mtrl-sci↗
arXiv2026

Multiferroic Properties of Electrospun CFO-BCTSn Nanocomposites for Magnetoelectric and Magnetic Field Sensing Applications

Multiferroic CFO-BCTSn composite nanofibers were synthesized using a sol-gel electrospinning method. Electron microscopy revealed well-defined fibers with diameters of 120-150 nm. Structural analyses using X-ray diffraction, Raman spectroscopy, and high-resolution transmission electron microscopy confirmed the coexistence of the spinel CFO phase and the perovskite BCTSn phase without detectable secondary phases. Magnetic hysteresis measurements demonstrated the magnetic behavior of the nanofibers, while piezoresponse force microscopy confirmed their piezoelectric properties. Magnetoelectric coupling was evidenced by differences between the magnetic hysteresis loops of electrically poled and unpoled samples. These lead-free composite nanofibers show potential for nanoscale magnetoelectric devices and magnetic field sensing applications.

cond-mat.mtrl-sci↗
arXiv2026

Ferroelectric KNbO3 nanoplatelets for thermally driven pyrocatalytic hydrogen evolution and dye degradation

Day- and night-induced thermal cycling offers a promising route for harvesting ambient thermal energy to drive sustainable hydrogen production and pollutant degradation. Pyroelectric materials enable this process by converting temperature fluctuations into surface charges capable of promoting catalytic water splitting and advanced oxidation reactions. In this work, we demonstrate efficient pyrocatalytic hydrogen evolution and Rhodamine B (RhB) degradation using orthorhombic ferroelectric Potassium niobate (KNbO$_3$) nanoplatelets (KN-np). Under thermal cycling between 20 and 50 $^\circ$C, KN-np achieved a hydrogen yield of 680 $\mu$mol g$^{-1}$ after 30 thermal cycles, corresponding to an average hydrogen production rate of 22.67 $\mu$mol g$^{-1}$ per cycle. In addition, KN-np exhibited excellent pyrocatalytic activity toward RhB degradation, reaching 84% removal after only 16 thermal cycles with an apparent kinetic rate constant of 0.11 cycle$^{-1}$. The remarkable catalytic performance is attributed to the strong spontaneous polarization and excellent pyroelectric properties of the KNbO$_3$ nanoplatelets, which promote efficient charge generation and interfacial redox reactions. These findings highlight the potential of KNbO$_3$ nanostructures as efficient pyrocatalysts for clean hydrogen production and environmental remediation.

cond-mat.mtrl-sci↗
arXiv2026

Enhancement in Magnetic and Magnetocaloric Properties of CoFe2O4 Nanofibers at Lower Temperatures

This research paper investigates new and first insights into the magnetic and magnetocaloric properties of one-dimensional (1D) cobalt ferrite CoFe2O4 (CFO) nanofibers elaborated by sol gel based electrospinning technique, particularly focusing on their behavior at low temperatures for specific applications. The calcined CFO nanofibers microstructural, structural, magnetic, and magnetocaloric properties were explored. The nanofibers (NFs) microstructure, with an average diameter of 210 nm, was examined by scanning and transmission electron microscopies (SEM, TEM). The X-ray diffraction (XRD) of the CFO nanofibers showed a pure cubic close-packed (c.c.p) spinel crystalline structure with the F d 3 -m space group. The Raman spectroscopic studies further confirm the cubic inverse spinel phase. The Magnetic properties were explored as a function of temperature, ranging from 10 to 300 K, a ferromagnetic behaviour was observed with the highest saturation magnetization of 75.87 emu g(-1) and a coercivity of 723 Oe at room temperature. The variation of the magnetic entropy was measured indirectly using the Maxwell approach with an increasing magnetic field. A maximum of Delta(S)=1.71 J K-1 was reached around 32 K. At 180 K, the associated adiabatic temperature change, Delta (Tmax), was 0.93 K, with a large RCP value of 7.58 J kg-1 was measured, which is reasonably high for the corresponding nanoparticles (NPs). This work may suggest that 1D CFO nanofibers offer a promising route for the production of nanostructured magnetic materials, potentially impacting various electronic and electromagnetic device applications at low temperatures.

cond-mat.mtrl-sci↗
arXiv2026

Rapid and Highly Efficient Synergistic Sonophotocatalytic Degradation of Methyl Orange with CuDoped LaFeO3 Perovskite Nanoparticles

The integration of sonocatalysis with photocatalysis offers a powerful strategy for advanced wastewater treatment by overcoming rapid charge carrier recombination in conventional photocatalytic systems. Although these processes are often treated separately due to their distinct mechanisms, their combination creates a highly efficient synergistic system. In this study, we investigate the sonophotocatalytic degradation of methyl orange (MO) using Cu-doped LaFeO3 perovskite nanoparticles. The Cu doped catalyst demonstrated excellent performance, achieving a degradation rate of 0.0455 min-1 and complete removal of MO within 120 minutes under combined ultrasonic and light irradiation. A strong synergistic effect was observed, with a synergy index of approximately 10, highlighting the enhanced interaction between sonocatalysis and photocatalysis. The catalyst also exhibited good stability and reusability, maintaining high efficiency over four consecutive cycles. Mechanistic studies using scavenger experiments revealed that hydroxyl radicals and photogenerated holes are the main reactive species responsible for degradation. A plausible reaction pathway is proposed based on these findings. Overall, Cu doped LaFeO3 shows superior sonophotocatalytic activity compared to the undoped material, demonstrating the potential of synergistic sonophotocatalytic processes for efficient pollutant removal.

cond-mat.mtrl-sci↗
arXiv2025

Current Advances in Magnetoelectric Composites with Various Interphase Connectivity Types

Magnetoelectric composites integrate the coupling between magnetic and piezoelectric materials to create new functionalities for potential technological applications. This coupling is typically achieved through the exchange of magnetic, electric, or elastic energy across the interfaces between the different constituent materials. Tailoring the strength of the magnetoelectric effect is primarily accomplished by selecting suitable materials for each constituent and by optimizing geometrical and microstructural designs. Various composite architectures, such as (0-3), (2-2), (1-3) and core-shell connectivities, have been studied to enhance magnetoelectric coupling and other required physical properties in composites. This review examines the latest advancements in magnetoelectric materials, focusing on the impact of different interphase connectivity types on their properties and performance. Before exploring magnetic-electric coupling, a brief overview of the historical background of multiferroic magnetoelectric composites is provided. Fundamental concepts underlying the magnetoelectric effect, piezoelectricity, and the magnetostrictive effect are explained, including their origins and examples of these materials' properties. So far, three types of magnetoelectric composite connectivities have been investigated experimentally: particulate composites (0-3), laminated and thin films (2-2), sticks embedded in matrix, core-shell particles, and coaxial fibers. An outlook on the prospects and scientific challenges in the field of multiferroic magnetoelectric composites is given at the end of this review.

cond-mat.mtrl-sci↗
arXiv2025

BCZT/LSMO/BCZT multilayer films for high temperature energy storage capacitors

Ba0.85Ca0.15Zr0.1Ti0.9O3/La0.8Sr0.2MnO3/Ba0.85Ca0.15Zr0.1Ti0.9O3 (BCZT/LSMO/BCZT) sandwich films were elaborated using the sol-gel spin coating process. The dielectric properties displayed excellent thermal stability with the temperature coefficient of capacitance, TCC, remaining within 10% between -50 C and 300 C. The high energy storage density, Wrec, of 11.8 J/cm3 observed in this sandwich films, is nearly twice as high as that of the BCZT films, with an efficiency, n, of 77% under a weak electric field of 800 kV/cm. Furthermore, the stability of Wrec and n was observed along the studied temperature interval making them promising candidates for high-temperature energy storage capacitors.

cond-mat.mtrl-sci↗
arXiv2024

Impact of Polymeric precursor and Auto-combustion on the Structural, Microstructural, Magnetic, and Magnetocaloric Properties of La0.8Sr0.2MnO3

In this work, La0.8Sr0.2MnO3 (LSMO) nanopowders are synthesized using two different methods: Pechini (LSMO-PC) and auto-combustion (LSMO-AC). Nanoparticle sizes, structural, magnetic, and magnetocaloric properties were determined and compared. The X-ray diffraction confirms the coexistence of two phases; rhombohedral symmetry with space group R-3c and orthorhombic symmetry with space group Pbnm, with the rhombohedral phase dominating. The scanning electron microscope images show that LSMO-PC has larger nanoparticle sizes (~495 nm) than LSMO-AC (~195 nm). The samples exhibit ferromagnetic properties with distinct hysteresis loops and Curie temperatures 340 K and 290 K for LSMO-PC and LSMO-AC respectively. The variation of the magnetic entropy was measured indirectly using the Maxwell approach with increasing magnetic field. For LSMO-PC it reaches a maximum -dSM=1.69 J/kg.K at 340 K and dH= 5 T. The associated adiabatic temperature change dTM is 1.04 K. While LSMO-PC demonstrates superior magnetic and magnetocaloric properties, LSMO-AC displays significant magnetocaloric thermal stability. The obtained values make LSMO-PC and LSMO-AC promising candidates for eco-friendly room-temperature magnetocaloric applications.

cond-mat.mtrl-sci↗
arXiv2023

Structural, dielectric and energy storage properties of BaO-Na2O-Nb2O5-P2O5 glass-ceramic

A series of (1-x)[(2BaO-0,5Na2O)-1P2O5] -xNb2O5 (BNPN, x=0,41, 0,43, 0,45, 0,48) glass-ceramics based on phosphate glasses have been prepared via a controlled-crystallization route. The structure, dielectric properties, interfacial polarization, and energy storage properties were systematically investigated. The x-ray diffraction results showed the simultaneous presence of Ba2NaNb5O15 tungsten bronze structure (TTB) and the NaNbO3 perovskite. A stable dielectric constant over a temperature range from 25-200{\deg}C, low dielectric losses less than 0,03, and excellent frequency stability at room temperature were obtained. The decrease in niobium content promoted TTB crystallization with the improvement of the high dielectric properties of the system. The optimum of the dielectric constant and recoverable energy storage density were obtained for BNP41 crystallized at 1000{\deg}C. Analyses of the complex impedance indicated that the niobium content and crystallization temperature affect the interfacial polarization.

cond-mat.mtrl-sci↗
arXiv2023

Effect of the BaO-Na$_2$O-Nb$_2$O$_5$-P$_2$O$_5$ glass addition on microstructure and dielectric properties of BNN ceramics

Barium sodium niobate Ba$_2$NaNb$_5$O$_{15}$ (BNN) ceramics with different amounts of BaO-Na$_2$O-Nb$_2$O$_5$-P$_2$O$_5$ (BNNP) glass were prepared via the conventional solid-state method. The effect of glass content on the structural, microstructure, and dielectric properties of BNN ceramics was investigated. The XRD results showed that no secondary phase was formed after adding BNNP glass. It was found that such additions reduce the average grain size and refine the microstructure of the obtained ceramics. Moreover, the samples exhibited a stable dielectric constant over the temperature range of 25$^\circ$C-150$^\circ$C, and their dielectric constants were significantly improved. The ceramic with 7.5 wt% BNNP glass content showed a dielectric constant which is more than twice as much as that of pure BNN ceramic, as well as a low dielectric loss of less than 5%.

physics.app-ph↗
arXiv2023

Magnetoelectric coupling in multiferroic CFO/BCTSn core shell nanofibers elaborated by co-axial electrospinning method

Multiferroic CoFe2O4-Ba0.95Ca0.05Ti0.89Sn0.11O3 core-shell nanofibers (CFO@BCTSn NFs) were synthesized by a sol-gel co-axial electrospinning technique. The scanning electron microscope and transmission electron microscope were used to check nanofibers' core-shell structure/configuration. X-ray diffraction and a high-resolution transmission electron microscope were used to confirm the spinel structure of CFO and the perovskite structure of BCTSn. The magnetic character of the resultant CFO@BCTSn NFs was determined by SQUID magnetometry. The piezoelectricity was verified using piezo-response force microscopy, which revealed an entirely covered ferroelectric shell outline, in accordance with SEM and TEM observations. The magnetoelectric (ME) coefficient was measured as a function of the applied external DC magnetic field. The maximum ME coefficient obtained for the CFO@BCTSn NFs was 346 mV cm-1 Oe-1. The high magnetoelectric coupling suggests that CFO@BCTSn NFs could be a promising candidate for magnetic field sensor and magnetoelectric device applications.

cond-mat.mtrl-sci↗
arXiv2023

Room-temperature magnetoelectric effect in lead-free multiferroic $(1-x)$ Ba$_{0.95}$Ca$_{0.05}$Ti$_{0.89}$Sn$_{0.11}$O$_3$-$(x)$CoFe$_2$O$_4$ particulate composites

Multiferroic particulate composites $(1-x)$ Ba$_{0.95}$Ca$_{0.05}$Ti$_{0.89}$Sn$_{0.11}$O$_3$-$(x)$CoFe$_2$O$_4$ with ($x$ = 0.1, 0.2, 0.3, 0.4 and 0.5) have been prepared by mechanical mixing of the calcined and milled individual ferroic phases. X-ray diffraction and Raman spectroscopy analysis confirmed the formation of both perovskite Ba$_{0.95}$Ca$_{0.05}$Ti$_{0.89}$Sn$_{0.11}$O$_3$ (BCTSn) and spinel CoFe$_2$O$_4$ (CFO) phases without the presence of additional phases. The morphological properties of the composites were provided by using Field Emission Scanning Electron Microscopy. The BCTSn-CFO composites exhibit multiferroic behavior at room temperature, as evidenced by ferroelectric and ferromagnetic hysteresis loops. The magnetoelectric (ME) coupling was measured under a magnetic field up to 10 kOe and the maximum ME response found to be 0.1 mV /cm/ Oe for the composition 0.7 BCTSn-0.3 CFO exhibiting a high degree of pseudo-cubicity and large density.

cond-mat.mtrl-sci↗
arXiv2022

Enhanced electrocaloric and energy-storage properties of environment-friendly ferroelectric Ba0.9Sr0.1Ti1-xSnxO3 ceramics

The electrocaloric (EC) effect and energy storage properties of eco-friendly ferroelectric Ba0.9Sr0.1Ti1-xSnxO3 (BSTS-x) ceramics prepared by the conventional solid-state reaction method were studied. Significant energy efficiency exceeding 80% was found in our samples. In particular, BSTS-5 and BSTS-10 samples exhibit 92% and 88% efficiency, respectively, over a wide temperature range around room temperature (RT). Direct EC measurement and an indirect method based on the thermodynamic approach were used to characterize the EC effect, and both yielded consistent results. The largest electrocaloric responsivity of 0.73 K mm/kV was obtained for BSTS-0 at 368 K with an adiabatic temperature change DT(EC) of 0.55 K at a low applied electric field of only 7.4 kV/cm. With increasing Sn-content, the EC response of BSTS-x ceramics decreases, while their diffuseness increases over an extensive temperature range, centered at RT. A significant coefficient of performance (COP > 26) was found for our samples. The obtained results demonstrate the possibility of designing eco-friendly materials with higher EC effect and energy efficiency for potential solid-state refrigeration and energy storage devices.

cond-mat.mtrl-sci↗
arXiv2022

Improved energy storage and electrocaloric properties of lead-free Ba0.85Ca0.15Zr0.1Ti0.9O3 ceramic

Lead-free ba0.85ca0.15zr0.1ti0.9o3 (bczt) ceramic powders were synthesized using the sol-gel method. to achieve high-energy storage and large electrocaloric effect in bulk ceramics the ceramics thickness was reduced. dielectric, ferroelectric, energy storage, and electrocaloric properties were investigated for bczt ceramic with 400 {\mu}m. here, pure crystalline structure and homogenous microstructure were identified by xrd analysis and sem measurements, respectively. the dielectric measurements revealed a maximum dielectric constant associated with ferroelectric-paraelectric phase transition. the maximum of {\epsilon} was 7841 around 352 k. furthermore, the bczt ceramic showed improved energy storage and electrocaloric properties. a high recoverable energy density wrec of 0.24 j/cm3 and a total energy density wtotal of 0.27 j/cm3 with an efficiency coefficient of ~ 88% at 423 k under an electric field of 55 kv/cm was obtained. besides, the maximum value of {\delta}t = 2.32 k, the electrocaloric responsivity {\zeta} = 0.42 k mm/kv, the refrigeration capacity rc= 4.59 j/kg and the coefficient of performance cop = 12.38 were achieved around 384 k under 55 kv/cm. the total energy density wtotal and the temperature change {\delta}t were also calculated by exploiting the landau-ginzburg-devonshire (lgd) theory. the theoretical results matched the experimental findings. these results suggest that the synthesized bczt ceramic with the reduced thickness could be a promising candidate for energy storage and electrocaloric applications.

cond-mat.mtrl-sci↗
arXiv2022

Electrocaloric effect and high energy storage efficiency in lead-free Ba$_{0.95}$Ca$_{0.05}$Ti$_{0.89}$Sn$_{0.11}$O$_3$ ceramic elaborated by sol-gel method

Structural, dielectric, ferroelectric, energy storage properties, and electrocaloric effect were studied in lead-free ceramic Ba$_{0.95}$Ca$_{0.05}$Ti$_{0.89}$Sn$_{0.11}$O$_3$ (BCTSn) elaborated by sol-gel method. Phase purity structure was confirmed from X-ray data using Rietveld refinement analysis which revealed the coexistence of tetragonal (P4mm) and orthorhombic (Amm2) symmetries at room temperature. Phase transitions were detected by dielectric and differential scanning calorimetry results. Energy storage properties were determined from P-E hysteresis, and the electrocaloric properties were calculated indirectly via the Maxwell approach. The large value of electrocaloric temperature change of $\Delta$T=0.807 K obtained at a relatively small field of 30 kV cm$^{-1}$ and high energy storage efficiency can make BCTSn ceramic a promising candidate for environmentally friendly refrigeration and energy storage applications.

cond-mat.mtrl-sci↗
arXiv2022

Enhanced RCP and large inverse magnetocaloric effect of CoFe$_2$O$_4$ nanoparticles synthesized by auto-combustion method

This work focuses on the microstructure, magnetic properties and magnetocaloric effect of CoFe$_2$O$_4$ (CFO) nanoparticles elaborated by sol-gel auto combustion method. The XRD investigation indicates that CFO is crystallized in a cubic spinel structure and the SEM micrograph shows a fine quasi-spherical with an average grain sizes of 160 nm. The temperature dependence of the Raman spectra reveals the ferromagnetic to paramagnetic (FM-PM) transition started from 723 K and the magnetization versus temperature measurements shows the Curie temperature located at T$_{\rm C}$ = 785 K. Large value of magnetocaloric temperature change of $\Delta$T =11.2 K with a high RCP of 687.56 J Kg$^{-1}$ are achieved indirectly via the Maxwell approach making our CFO nanopowder suitable candidate for both environmentally friendly magnetic refrigeration and medical applications at ambient temperature.

cond-mat.mtrl-sci↗
arXiv2020

Structural, Dielectric and Ferroelectric Properties of Lead-free BCZT Ceramics Elaborated by Low-temperature Hydrothermal Processing

Lead-free Ba0.85Ca0.15Zr0.10Ti0.90O3 (BCZT) ceramics have demonstrated excellent dielectric, ferroelectric and piezoelectric properties in comparison to lead-based materials. The synthesis of pure and crystalline BCZT nanopowders at low temperatures of 25, 80 and 160 C was reported previously by using a sol-gel method followed by a hydrothermal route. In this study, the structural, dielectric and ferroelectric properties of sintered BCZT ceramics at 1250 °C for 10h were investigated. XRD measurements revealed the presence of a single perovskite phase at room temperature with the coexistence of the orthorhombic and tetragonal symmetries. The increase of grain size and the ceramic density in BCZT ceramics result in an enhancement of the dielectric and ferroelectric properties of BCZT ceramics. More interestingly, the synthesis temperature of BCZT powders with high dielectric and ferroelectric properties could be decreased to a low temperature of 160 °C, which is about 1200 °C lower when compared with solid-state reaction and 840 °C lower when compared with sol-gel methods. The BCZT ceramics elaborated at 160 °C revealed excellent electrical properties. Hence, the use of low-temperature hydrothermal processing can be encouraging for the synthesis of lead-free ceramics with high dielectric and ferroelectric properties.

cond-mat.mtrl-sci↗