SearcharxivSearch

arXiv subjects

Datao Gong

Publications and source records attributed to Datao Gong.

At least 19 recordsLinked to original sources

A Complexity Agnostic Clustering Engine for Time Projection Chambers and its Implementation in FPGA

A clustering functional block implemented in field-programable-gate-array (FPGA) for time projection chambers (TPC) operating with predictable time regardless the complexity of the event is described in this paper. The clustering functional block reorganizes input data and the hits data belonging to the same clusters are output together for further process in the later stages. The clustering operation consists of two phases, data filling phase and data outputting phase, and the later uses the same number of clock cycles as the data filling phase. The clustering block can accommodate events with arbitrary number of clusters and number of hits per cluster as long as the total number of hits is within a predesigned limit. The operation time is exactly twice of the data filling time with no residual O(n2) term. The clustering block has been implemented with operating frequency of 200 MHz in a low-cost FPGA evaluation module and test results confirm the expected performance.

physics.ins-det

Radiation Resistance of Ge-doped Multi-Mode Fiber for Optical Links in Collider Experiments

The applications of optical links in collider experiments provide the advantage of high-speed data transmission with low mass fibers over distances of a few hundred meters. Ge-doped multi-mode fibers are evaluated for radiation tolerance in ionizing doses of Co-60 gamma rays. The Radiation-Induced Attenuation (RIA) varies significantly depending on doping substances and fabrication technologies. A type of telecom-grade fiber has demonstrated an RIA of 0.05 dB/m under a total ionizing dose of 300 kGy(SiO2). The dependence on dose rate is compared in the range between 5 Gy/hr and 1.4 kGy/hr, and the annealing recovery is observed after the Co-60 source is shielded. The temperature dependence is investigated across a range of -15 oC to room temperature. At cold temperatures, stagnant annealing leads to a substantially higher RIA during irradiation. The recovery of radiation-induced defects is typically within a few hours, resulting in similar RIA levels regardless of the dose rate and temperature during exposure. Ge-doped fibers of chosen fabrication methods are capable of enduring high ionizing doses for use in high-energy physics experiments.

hep-ex

Characteristics of Ge-doped Multi-Mode Fibers in Total Ionizing Dose

Purpose: The fiber optical links in 850 nm band with Ge-doped multi-mode (MM) fibers are well developed for data transmission at 10 Gbps and higher. The applications in nuclear environments require radiation resistance. The characteristics of Ge-doped MM fibers are investigated for Radiation Induced Attenuation (RIA) in Total Ionizing Dose (TID). Methods: Commercial samples of Ge-doped MM fibers were irradiated in Go-60 gamma rays at dose rates of 5 to 1.4k Gy(SiO2)/hr. The fiber samples were packaged in water tanks maintained at constant temperatures in the range of -15 to 45 degC. The optical power transmitted through the fibers were recorded in irradiation, and in annealing when the source was shielded. The measurements of RIA in time are analyzed for dose rate and temperature dependences. Results: Ge-doped fiber samples of OM2 to OM4 grades were investigated for attenuation of optical power in radiation ionizing dose. Depending on the fabrication technology, two of the fiber types show radiation resistance with the RIAs of 0.2 dB/m and 0.05 dB/m, respectively, for the TID of 300 kGy(SiO2). At low dose rate of 5 Gy/hr, the RIA increases steadily and the annealing of low density ionizing defects does not cause notable deviation. At 1.4 kGy/hr the accumulated defects result to twice higher RIA during irradiation, and is worsen to a factor three in cold temperature. However, once the source is shielded the recovery is effective in a few hours. Conclusion: The telecom products of 850 nm Ge-doped MM fibers provide high speed communication in distances of a few hundred meters. The industrial fabrication methods provide fibers that can endure radiation ionizing dose for applications in nuclear instrumentation.

physics.med-ph

ETROC1: The First Full Chain Precision Timing Prototype ASIC for CMS MTD Endcap Timing Layer Upgrade

We present the design and characterization of the first full chain precision timing prototype ASIC, named ETL Readout Chip version 1 (ETROC1) for the CMS MTD endcap timing layer (ETL) upgrade. The ETL utilizes Low Gain Avalanche Diode (LGAD) sensors to detect charged particles, with the goal to achieve a time resolution of 40 - 50 ps per hit, and 30 - 40 ps per track with hits from two detector layers. The ETROC1 is composed of a 5 x 5 pixel array and peripheral circuits. The pixel array includes a 4 x 4 active pixel array with an H-tree shaped network delivering clock and charge injection signals. Each active pixel is composed of various components, including a bump pad, a charge injection circuit, a pre-amplifier, a discriminator, a digital-to-analog converter, and a time-to-digital converter. These components play essential roles as the front-end link in processing LGAD signals and measuring timing-related information. The peripheral circuits provide clock signals and readout functionalities. The size of the ETROC1 chip is 7 mm x 9 mm. ETROC1 has been fabricated in a 65 nm CMOS process, and extensively tested under stimuli of charge injection, infrared laser, and proton beam. The time resolution of bump-bonded ETROC1 + LGAD chipsets reaches 42 - 46 ps per hit in the beam test.

physics.ins-det

The 120Gbps VCSEL Array Based Optical Transmitter (ATx) Development for the High-Luminosity LHC (HL-LHC) Experiments

The integration of a Verticle Cavity Surface-Emitting Laser (VCSEL) array and a driving Application-Specific Integrated Circuit (ASIC) in a custom optical array transmitter module (ATx) for operation in the detector front-end is constructed, assembled and tested. The ATx provides 12 parallel channels with each channel operating at 10 Gbps. The optical transmitter eye diagram passes the eye mask and the bit-error rate (BER) less than 1E-12 transmission is achieved at 10 Gbps/ch. The overall insertion loss including the radiation induced attenuation is sufficiently low to meet the proposed link budget requirement.

physics.ins-det

Optical Data Transmission ASICs for the High-Luminosity LHC (HL-LHC) Experiments

We present the design and test results of two optical data transmission ASICs for the High-Luminosity LHC (HL-LHC) experiments. These ASICs include a two-channel serializer (LOCs2) and a single-channel Vertical Cavity Surface Emitting Laser (VCSEL) driver (LOCld1V2). Both ASICs are fabricated in a commercial 0.25-um Silicon-on-Sapphire (SoS) CMOS technology and operate at a data rate up to 8 Gbps per channel. The power consumption of LOCs2 and LOCld1V2 are 1.25 W and 0.27 W at 8-Gbps data rate, respectively. LOCld1V2 has been verified meeting the radiation-tolerance requirements for HL-LHC experiments.

physics.ins-det

The Design of a High Speed Low Power Phase Locked Loop

The upgrade of the ATLAS Liquid Argon Calorimeter readout system calls for the development of radiation tolerant, high speed and low power serializer ASIC. We have designed a phase locked loop using a commercial 0.25 um Silicon-on-Sapphire (SoS) CMOS technology. Post-layout simulation indicates that tuning range is 3.79-5.01 GHz and power consumption is 104 mW. The PLL has been submitted for fabrication. The design and simulation results are presented.

physics.ins-det

The Clock Distribution System for the ATLAS Liquid Argon Calorimeter Phase-I Upgrade Demonstrator

A prototype Liquid-argon Trigger Digitizer Board (LTDB), called the LTDB Demonstrator, has been developed to demonstrate the functions of the ATLAS Liquid Argon Calorimeter Phase-I trigger electronics upgrade. Forty Analog-to-Digital converters and four FPGAs with embedded multi-gigabit-transceivers on each Demonstrator need high quality clocks. A clock distribution system based on commercial components has been developed for the Demonstrator. The design of the clock distribution system is presented. The performance of the clock distribution system has been evaluated. The components used in the clock distribution system have been qualified to meet radiation tolerance requirements of the Demonstrator.

physics.ins-det

The VCSEL-based Array Optical Transmitter (ATx) Development Towards 120-Gbps Link for Collider Detector: Development Update

A compact radiation-tolerant array optical transmitter module (ATx) is developed to provide data transmission up to 10Gbps per channel with 12 parallel channels for collider detector applications. The ATx integrates a Vertical Cavity Surface-Emitting Laser (VCSEL) array and driver circuitry for electrical to optical conversion, an edge warp substrate for the electrical interface and a micro-lens array for the optical interface. This paper reports the continuing development of the ATx custom package. A simple, high-accuracy and reliable active-alignment method for the optical coupling is introduced. The radiation-resistance of the optoelectronic components is evaluated and the inclusion of a custom-designed array driver is discussed.

physics.ins-det

JTAG-based Remote Configuration of FPGAs over Optical Fibers

In this paper, a remote FPGA-configuration method based on JTAG extension over optical fibers is presented. The method takes advantage of commercial components and ready-to-use software such as iMPACT and does not require any hardware or software development. The method combines the advantages of the slow remote JTAG configuration and the fast local flash memory configuration. The method has been verified successfully and used in the Demonstrator of Liquid-Argon Trigger Digitization Board (LTDB) for the ATLAS liquid argon calorimeter Phase-I trigger upgrade. All components on the FPGA side are verified to meet the radiation tolerance requirements.

physics.ins-det

High-Speed Serial Optical Link Test Bench Using FPGA with Embedded Transceivers

We develop a custom Bit Error Rate test bench based on Altera's Stratix II GX transceiver signal integrity development kit, demonstrate it on point-to-point serial optical link with data rate up to 5 Gbps, and compare it with commercial stand alone tester. The 8B/10B protocol is implemented and its effects studied. A variable optical attenuator is inserted in the fibre loop to induce transmission degradation and to measure receiver sensitivity. We report comparable receiver sensitivity results using the FPGA based tester and commercial tester. The results of the FPGA also shows that there are more one-to-zero bit flips than zero-to-one bit flips at lower error rate. In 8B/10B coded transmission, there are more word errors than bit flips, and the total error rate is less than two times that of non-coded transmission. Total error rate measured complies with simulation results, according to the protocol setup.

physics.ins-det

Development of A 16:1 serializer for data transmission at 5 Gbps

Radiation tolerant, high speed and low power serializer ASIC is critical for optical link systems in particle physics experiments. Based on a commercial 0.25 um silicon-on-sapphire CMOS technology, we design a 16:1 serializer with 5 Gbps serial data rate. This ASIC has been submitted for fabrication. The post-layout simulation indicates the deterministic jitter is 54 ps (pk-pk) and random jitter is 3 ps (rms). The power consumption of the serializer is 500 mW. The design details and post layout simulation results are presented in this paper.

physics.ins-det

MUX64, an analogue 64-to-1 multiplexer ASIC for the ATLAS High Granularity Timing Detector

We present the design and the performance of MUX64, a 64-to-1 analogue multiplexer ASIC for the ATLAS High Granularity Timing Detector (HGTD). The MUX64 transmits one of its 64 inputs selected by six address lines for the voltages or temperatures being monitored to an lpGBT ADC channel. The prototype ASICs fabricated in TSMC 130 nm CMOS technology were prepared in wire-bonding and QFN88 packaging format. A total of 280 chips was examined for functionality and quality assurance. The accelerated aging test conducted at 85 degrees celsius shows negligible degradation over 16 days.

physics.ins-det

Response of a Commercial 0.25 um Thin-Film Silicon-on-Sapphire CMOS Technology to Total Ionizing Dose

The radiation response of a 0.25 um silicon-on-sapphire CMOS technology is characterized at the transistor and circuit levels utilizing both standard and enclosed layout devices. Device-level characterization showed threshold voltage change of less than 170 mV and leakage current change of less than 1 nA for individual nMOSFET and pMOSFET devices at a total dose of 100 krad(SiO2). The increase in power supply current at the circuit level was less than 5%, consistent with the small change in off-state transistor leakage current. The technology exhibits good characteristics for use in the electronics of the ATLAS experiment at the Large Hadron Collider.

physics.ins-det

R&D Towards Cryogenic Optical Links

A number of critical active and passive components of optical links have been tested at 77 K or lower temperatures, demonstrating potential development of optical links operating inside the liquid argon time projection chamber (LArTPC) detector cryostat. A ring oscillator, individual MOSFETs, and a high speed 16:1 serializer fabricated in a commercial 0.25-um silicon-on-sapphire CMOS technology continued to function from room temperature to 4.2 K, 15 K, and 77 K respectively. Three types of laser diodes lase from room temperature to 77 K. Optical fibers and optical connectors exhibited minute attenuation changes from room temperature to 77 K.

physics.ins-det

Cryogenic digital data links for the liquid argon time projection chamber

In this paper we present the cryogenic functionality of the components of data links for the Liquid Argon Time Projection Chamber (LArTPC), a potential far site detector technology of the Long-Baseline Neutrino Experiment (LBNE). We have confirmed that an LVDS driver can drive a 20-meter CAT5E twisted pair up to 1 gigabit per second at the liquid nitrogen temperature (77 K). We have verified that a commercial-off-the-shelf (COTS) serializer, a laser diode driver, laser diodes, optical fibers and connectors, and field-programming gate arrays (FPGA's) continue to function at 77 K. A variety of COTS resistors and capacitors have been tested at 77 K. All tests we have conducted show that the cryogenic digital data links for the liquid argon time projection chamber are promising.

physics.ins-det

The Miniature Optical Transmitter and Transceiver For the High-Luminosity LHC (HL-LHC) experiments

We present the design and test results of the Miniature optical Transmitter (MTx) and Transceiver (MTRx) for the high luminosity LHC (HL-LHC) experiments. MTx and MTRx are Transmitter Optical Subassembly (TOSA) and Receiver Optical Subassembly (ROSA) based. There are two major developments: the Vertical Cavity Surface Emitting Laser (VCSEL) driver ASIC LOCld and the mechanical latch that provides the connection to fibers. In this paper, we concentrate on the justification of this work, the design of the latch and the test results of these two modules with a Commercial Off-The-Shelf (COTS) VCSEL driver.

physics.ins-det

A line code with quick-resynchronization capability and low latency for the optical data links of LHC experiments

We propose a line code that has fast resynchronization capability and low latency. Both the encoder and decoder have been implemented in FPGAs. The encoder has also been implemented in an ASIC. The latency of the whole optical link (not including the optical fiber) is estimated to be less than 73.9 ns. In the case of radiation-induced link synchronization loss, the decoder can recover the synchronization in 25 ns. The line code will be used in the ATLAS liquid argon calorimeter Phase-I trigger upgrade and can also be potentially used in other LHC experiments.

physics.ins-det