arXiv subjects

David Kolenatý

Publications and source records attributed to David Kolenatý.

4 recordsLinked to original sources

arXiv2026

Enhanced hydrogen response of copper-doped TiO$_2$ synthesised by helium-assisted magnetron sputtering

Cu-doped TiO$_2$ thin films for hydrogen sensing were synthesised by reactive DC magnetron sputtering in Ar/O$_2$/He mixtures, with the He fraction used as a control parameter for film growth. By combining normal-angle deposition (NAD) and glancing-angle deposition (GLAD) with post-deposition annealing, the effects of He on microstructure formation and sensor performance were examined. X-ray diffraction and electron microscopy revealed that He promotes nanostructuring, lattice expansion in as-deposited NAD films, increased porosity after annealing, and a stronger anatase character in the final oxide layers. These structural changes, which enhance the reactive surface area, lead to improved hydrogen sensing at 300\,$^\circ$C in 1~vol.\,\% H$_2$. The response of NAD films increased from 1.4 to 6.0 simply by replacing part of the argon with helium, whereas GLAD films showed only a modest increase. The observed nanostructuring is discussed in terms of a simulation-supported growth scenario involving energetic backscattered He, a reduced hammering effect, and cooling-related suppression of adatom mobility, which together favour the formation of a more open sensing layer. Helium-assisted sputtering represents a useful physical route for tailoring oxide thin films for gas-sensing applications.

cond-mat.mtrl-sci↗

arXiv2026

Corrosion-resistant and conductive Ti-Nb-O coatings tailored for ultra-low Pt-loaded BPPs and PTLs in PEM electrolyzers

We develop highly corrosion-resistant and conductive Ti-Nb-O coatings for metallic components -- bipolar plates (BPPs) and porous transport layers (PTLs) -- in PEM water electrolyzers. Using reactive high-power impulse magnetron sputtering (HiPIMS), we deposit compact 200 nm bilayer coatings onto SS316L substrates, systematically tailoring their composition. By precisely controlling oxygen partial pressure and Nb/Ti ratio, we adjust stoichiometry and structure, directly affecting electrical resistivity and corrosion resistance. We examine interfacial contact resistance (ICR) and electrochemical parameters before and after accelerated corrosion testing. Optimized coatings exhibit resistivity on the order of 10^-4 Ohmcm and extremely low corrosion current densities (J_corr = 0.01-0.08 uA/cm^2), well below the U.S. DOE 2026 target. Most importantly, these coatings enable the ICR target after accelerated corrosion testing with a Pt overlayer as thin as 5 nm, reducing Pt loading by up to two orders of magnitude compared to conventional approaches.

cond-mat.mtrl-sci↗

arXiv2025

Ultra-low-resistivity nitrogen-doped p-type Cu2O thin films fabricated by reactive HiPIMS

We have successfully fabricated the nitrogen-doped cuprous oxide thin films on the amorphous standard soda-lime glass by reactive high-power impulse magnetron sputtering. The energy of film-forming particles was controlled by the value of pulse-averaged target power density, which has a significant impact on the elemental composition, structure and optoelectrical properties of the films. We have shown that the high-energy regime is more suitable for preserving Cu2O structure and leads to continuous substitution of oxygen by nitrogen compared with the low-energy regime. Moreover, in the high-energy regime, it is possible, to some extent, to independently control the electrical resistivity and optical properties. The electrical resistivity decreases down to 5 x10-2 ohm.cm at the optical band gap 2.0-2.3 eV. Special attention is paid to the formation of nitrogen molecules and their ability to form shallow acceptor states. Experimental results supported by our DFT calculations indicate that N2 replacing Cu in the Cu2O lattice is one possible (but not the only possible) acceptor. We have also found that the formation of nitrogen molecules is preferred in a high-energy regime.

cond-mat.mtrl-sci↗

arXiv2022

Electron-positron pairs and radioactive nuclei production by irradiation of high-Z target with γ-photon flash generated by an ultra-intense laser in the $λ^3$ regime

This paper studies the interaction of laser-driven $γ$-photons and high energy charged particles with high-Z targets through Monte-Carlo simulations. The interacting particles are taken from particle-in-cell simulations of the interaction of a tightly-focused ultraintense laser pulse with a titanium target. Lead is chosen as the secondary high-Z target owing to its high cross section of the giant dipole resonance and electron-positron pair production. The results reveal an ultra-short ultra-relativistic collimated positron population and their energy spectra, angular distribution, and temporal profile are found. We investigate the target thickness dependence of the resulting total numbers and total kinetic energies of various particle species emitted from the lead target irradiated with laser-generated $γ$-photons and charged particles separately. We plot the charts of residual high-Z nuclides generated by irradiation of the lead target. Owing to the short pulse duration, the $γ$-photon, electron-positron, and neutron sources can find applications in material science, nuclear physics, laboratory astrophysics, and as injectors in laser-based accelerators of charged particles.

physics.comp-ph↗