arXiv subjects

David Longuevergne

Publications and source records attributed to David Longuevergne.

6 recordsLinked to original sources

arXiv2026

First Experimental Characterization of Plasma Parameters and Carbon Decontamination Rates in a Microwave Resonator Used in Particle Accelerators

In-situ plasma processing of superconducting radio frequency (SRF) cavities is a performance recovery technique used to mitigate the field emission limiting phenomenon. It has been proved very effective at major particle accelerator facilities such as SNS, CEBAF, FRIB, FNAL and C-ADS. This technique is based on the ignition of a noble-gas/oxygen plasma inside the cavity over several hours to remove hydrocarbon-based contamination, responsible for the parasitic field emission degradation observed after several years of operation. Despite a large experimental R\&D effort from the community, plasma parameters and cleaning rates under various experimental conditions have never been directly evaluated. In this study, plasma parameters were measured using a Langmuir probe and cleaning rates thanks to a quartz crystal microbalance (QCM) coated with an amorphous carbon film to simulate a carbon-based contamination. In this article, the main results from a large parameter space are discussed along with guidelines for improving the plasma processing effectiveness in SRF cavities. The encountered technical challenges are also discussed, as the SRF cavity is by design not intended to be a plasma reactor.

physics.acc-ph↗

arXiv2025

Impact of metallographic polishing on the RF properties of Niobium for SRF applications

The performance of superconducting radio-frequency (SRF) cavities made of Niobium is tied to the quality of their inner surfaces exposed to the radio frequency (RF) waves. Future superconducting particle accelerators, because of their dimensions or the unprecedented stringent technical requirements, require the development of innovative surface processing techniques to improve processing reliability and if possible ecological footprint and cost, compared to conventional chemical processes. Metallographic polishing (MP) has emerged as a promising polishing technology to address these challenges. Previous studies focused on the characterization of the processed material surface at room temperature in the absence of RF waves. However, the evaluation of material properties, such as surface resistance under RF, at cryogenic temperature has failed, primarily due to the unavailability of devices capable of achieving the necessary resolution in the nanohm range. To overcome this limitation, a quadrupole resonator (QPR) has been utilized. The RF results demonstrate that the MP polishing, developed to preserve a high-quality niobium surface with very low surface resistance, is highly effective compared to conventional polishing. This conclusion is further supported by topography and microstructural analysis of the QPR top-hat samples, which revealed the clear superiority of the metallographic approach.

physics.acc-ph↗

arXiv2025

Cryogenics of a superconducting LINAC : SPIRAL2 from commissioning to operation

The SPIRAL2 superconducting linear accelerator (LINAC), which has been operational since 2019, employs superconducting, independently phased RF resonators to deliver a wide range of particle beams. Designed for flexibility in particle types, intensities, and energies, it utilizes superconducting quarter-wave resonators (QWRs), whose performances are critically dependent on the reliability of the cryogenic operation. This paper reviews the evolution from commissioning to the routine operation of the SPIRAL2 cryogenic system, initially commissioned in 2017. It highlights the key challenges encountered, including thermo-acoustic oscillations, thermal management, and abnormal behavior of cavities. Furthermore, it explores the integration of thermodynamic modeling and machine learning techniques to enhance system control and diagnose issues. This work serves as a comprehensive resource for advancing the cryogenic operation and performance of superconducting LINACs.

physics.acc-ph↗

arXiv2024

SRF programs towards High-Q/High-G cavities in IJCLab

IJCLab has been leading the development and deployment of low-$β$ Superconducting Radio Frequency (SRF) cavities for proton and heavy ion accelerators. We are launching an electron accelerator project for sustainable Energy Recovery Linac (iSAS/PERLE) with state-of-the-art SRF cavities at 800~MHz. Our proposal includes advanced heat treatment of such cavities to reach an excellent quality factor of $3\times 10^{10}$ at $22$~MV/m. In this paper, we overview the status of this activity.

physics.acc-ph↗

arXiv2024

Reducing two-level system dissipations in 3D superconducting Niobium resonators by atomic layer deposition and high temperature heat treatment

Superconducting qubits have arisen as a leading technology platform for quantum computing which is on the verge of revolutionizing the world's calculation capacities. Nonetheless, the fabrication of computationally reliable qubit circuits requires increasing the quantum coherence lifetimes, which are predominantly limited by the dissipations of two-level system (TLS) defects present in the thin superconducting film and the adjacent dielectric regions. In this paper, we demonstrate the reduction of two-level system losses in three-dimensional superconducting radio frequency (SRF) niobium resonators by atomic layer deposition (ALD) of a 10 nm aluminum oxide Al2O3 thin films followed by a high vacuum (HV) heat treatment at 650 °C for few hours. By probing the effect of several heat treatments on Al2O3-coated niobium samples by X-ray photoelectron spectroscopy (XPS) plus scanning and conventional high resolution transmission electron microscopy (STEM/HRTEM) coupled with electron energy loss spectroscopy (EELS) and (EDX) , we witness a dissolution of niobium native oxides and the modification of the Al2O3-Nb interface, which correlates with the enhancement of the quality factor at low fields of two 1.3 GHz niobium cavities coated with 10 nm of Al2O3.

physics.app-ph↗

arXiv2021

Impact of geometry on the magnetic flux trapping of superconducting accelerating cavities

Controlling trapped magnetic flux in superconducting radiofrequency (RF) cavities is of crucial importance in modern accelerator projects. In order to study flux trapping efficiency and sensitiv- ity of surface resistance, dedicated experiments have been carried out on different types of low-\b{eta} superconducting accelerating cavities. Even under almost full trapping conditions, we found that the measured magnetic sensitivities of these cavity geometries were significantly lower than the theoretical values predicted by commonly-used models based on local material properties. This must be resolved by taking account of geometrical effects of flux trapping and flux oscillation under RF surface current in such cavity shape. In this paper, we propose a new approach to convolute the influence of geometries. We point out a puzzling contradiction between sample measurements and recent cavity experiments, which leads to two different hypotheses to simulate oscillating flux trapped in the cavity surface. A critical reconsideration of flux oscillation by the RF Lorentz force, compared with temperature mapping studies in elliptical cavities, favoured the results of previous sample measurements, which suggested preferential flux trapping of normal component to the cavity inner surface. Based on this observation, we builded a new model to our experimental results and the discrepancy between old theory and data were resolved.

physics.acc-ph↗