arXiv subjects

David-Leon Pohl

Publications and source records attributed to David-Leon Pohl.

8 recordsLinked to original sources

arXiv2021

Characterization of passive CMOS sensors with RD53A pixel modules

Both the current upgrades to accelerator-based HEP detectors (e.g. ATLAS, CMS) and also future projects (e.g. CEPC, FCC) feature large-area silicon-based tracking detectors. We are investigating the feasibility of using CMOS foundries to fabricate silicon radiation detectors, both for pixels and for large-area strip sensors. A successful proof of concept would open the market potential of CMOS foundries to the HEP community, which would be most beneficial in terms of availability, throughput and cost. In addition, the availability of multi-layer routing of signals will provide the freedom to optimize the sensor geometry and the performance, with biasing structures implemented in poly-silicon layers and MIM-capacitors allowing for AC coupling. A prototyping production of strip test structures and RD53A compatible pixel sensors was recently completed at LFoundry in a 150nm CMOS process. This presentation will focus on the characterization of pixel modules, studying the performance in terms of charge collection, position resolution and hit efficiency with measurements performed in the laboratory and with beam tests. We will report on the investigation of RD53A modules with 25x100 mu^2 cell geometry.

physics.ins-det↗

arXiv2021

Radiation tolerant, thin, passive CMOS sensors read out with the RD53A chip

The radiation hardness of passive CMOS pixel sensors fabricated in 150 nm LFoundry technology is investigated. CMOS process lines are especially of interest for large-scale silicon detectors as they offer high production throughput at comparatively low cost. Moreover, several features like poly-silicon resistors, MIM-capacitors and several metal layers are available which can help enhance the sensor design. The performance of a 100 $\mathrm{\mu}$m thin passive CMOS sensor with a pixel pitch of 50 $\mathrm{\mu}$m at different irradiation levels, 5 $\times$ 10$^{15}$n$_{\mathrm{eq}}$cm$^{-2}$ and 1 $\times$ 10$^{16}$n$_{\mathrm{eq}}$cm$^{-2}$, is presented. The sensor was bump-bonded and read out using the RD53A readout chip. After the highest fluence a hit-detection efficiency larger than 99% is measured for minimum ionising particles. The measured equivalent noise charge is comparable to conventional planar pixel sensors. Passive CMOS sensors are thus an attractive option for silicon detectors operating in radiation harsh environments like the upgrades for the LHC experiments.

physics.ins-det↗

arXiv2020

BDAQ53, a versatile pixel detector readout and test system for the ATLAS and CMS HL-LHC upgrades

BDAQ53 is a readout system and verification framework for hybrid pixel detector readout chips of the RD53 family. These chips are designed for the upgrade of the inner tracking detectors of the ATLAS and CMS experiments. BDAQ53 is used in applications where versatility and rapid customization are required, such as in laboratory testing environments, test beam campaigns, and permanent setups for quality control measurements. It consists of custom and commercial hardware, a Python-based software framework, and FPGA firmware. BDAQ53 is developed as open source software with both software and firmware being hosted in a public repository.

physics.ins-det↗

arXiv2020

Improving the Spatial Resolution of Silicon Pixel Detectors through Sub-pixel Cross-coupling

We present a concept to improve the spatial resolution of silicon pixel-detectors via the implementation of a sub-pixel cross-coupling, which introduces directional charge sharing between pixels. The charge-collection electrode is segmented into sub-pixels and each sub-pixel is coupled to the closest sub-pixel of the neighboring pixel. Such coupling schema is evaluated for a model sensor design with $50 μm \times 50 μm$ pixels and AC-coupled sub-pixels. A first-order SPICE simulation is used, to determine feasible coupling strengths and assess the influence on the charge-collection efficiency. The impact of the coupling strength on spatial resolution is studied with a dedicated simulation, taking into account charge-cloud evolution, energy-loss straggling, electronic noise, and the charge detection-threshold. Using simplifying assumptions, such as perpendicular tracks and no gaps between charge-collection electrodes, an improvement of the spatial resolution by up to approximately $30\%$ is obtained in comparison to the standard planar pixel layout.

physics.ins-det↗

arXiv2019

The Monopix chips: Depleted monolithic active pixel sensors with a column-drain read-out architecture for the ATLAS Inner Tracker upgrade

Two different depleted monolithic CMOS active pixel sensor (DMAPS) prototypes with a fully synchronous column-drain read-out architecture were designed and tested: LF-Monopix and TJ-Monopix. These chips are part of a R&D effort towards a suitable implementation of a CMOS DMAPS for the HL-LHC ATLAS Inner Tracker. LF-Monopix was developed using a 150nm CMOS process on a highly resistive substrate (>2 k$Ω\,$cm), while TJ-Monopix was fabricated using a modified 180 nm CMOS process with a 1 k$Ω\,$cm epi-layer for depletion. The chips differ in their front-end design, biasing scheme, pixel pitch, dimensions of the collecting electrode relative to the pixel size (large and small electrode design, respectively) and the placement of read-out electronics within such electrode. Both chips were operational after thinning down to 100 $\mathrmμ$m and additional back-side processing in LF-Monopix for total bulk depletion. The results in this work include measurements of their leakage current, noise, threshold dispersion, response to minimum ionizing particles and efficiency in test beam campaigns. In addition, the outcome from measurements after irradiation with neutrons up to a dose of $1\times10^{15}\,\mathrm{n_{eq} / cm}^{2}$ and its implications for future designs are discussed.

physics.ins-det↗

arXiv2017

Neutron irradiation test of depleted CMOS pixel detector prototypes

Charge collection properties of depleted CMOS pixel detector prototypes produced on p-type substrate of 2 k$Ω$cm initial resistivity (by LFoundry 150 nm process) were studied using Edge-TCT method before and after neutron irradiation. The test structures were produced for investigation of CMOS technology in tracking detectors for experiments at HL-LHC upgrade. Measurements were made with passive detector structures in which current pulses induced on charge collecting electrodes could be directly observed. Thickness of depleted layer was estimated and studied as function of neutron irradiation fluence. An increase of depletion thickness was observed after first two irradiation steps to 1$\cdot$10$^{13}$ n/cm$^{2}$ and 5$\cdot$10$^{13}$ n/cm$^{2}$ and attributed to initial acceptor removal. At higher fluences the depletion thickness at given voltage decreases with increasing fluence because of radiation induced defects contributing to the effective space charge concentration. The behaviour is consistent with that of high resistivity silicon used for standard particle detectors. The measured thickness of the depleted layer after irradiation with 1$\cdot$10$^{15}$ n/cm$^{2}$ is more than 50 $μ$m at 100 V bias. This is sufficient to guarantee satisfactory signal/noise performance on outer layers of pixel trackers in HL-LHC experiments.

physics.ins-det↗

arXiv2016

Characterization of Fully Depleted CMOS Active Pixel Sensors on High Resistivity Substrates for Use in a High Radiation Environment

Depleted CMOS active sensors (DMAPS) are being developed for high-energy particle physics experiments in high radiation environments, such as in the ATLAS High Luminosity Large Hadron Collider (HL-LHC). Since charge collection by drift is mandatory for harsh radiation environment, the application of high bias voltage to high resistive sensor material is needed. In this work, a prototype of a DMAPS was fabricated in a 150nm CMOS process on a substrate with a resistivity of >2 kΩcm that was thinned to 100 μm. Full depletion occurs around 20V, which is far below the breakdown voltage of 110 V. A readout chip has been attached for fast triggered readout. Presented prototype also uses a concept of sub-pixel en/decoding three pixels of the prototype chip are readout by one pixel of the readout chip. Since radiation tolerance is one of the largest concerns in DMAPS, the CCPD_LF chip has been irradiated with X-rays and neutrons up to a total ionization dose of 50 Mrad and a fluence of 10E15neq/cm2, respectively.

physics.ins-det↗

arXiv2014

A method for precise charge reconstruction with pixel detectors using binary hit information

A method is presented to precisely reconstruct charge spectra with pixel detectors using binary hit information of individual pixels. The method is independent of the charge information provided by the readout circuitry and has a resolution mainly limited by the electronic noise. It relies on the ability to change the detection threshold in small steps while counting hits from a particle source. The errors are addressed and the performance of the method is shown based on measurements with the ATLAS pixel chip FE-I4 bump bonded to a 230 μm 3D-silicon sensor. Charge spectra from radioactive sources and from electron beams are presented serving as examples. It is demonstrated that a charge resolution (σ<200 e) close to the electronic noise of the ATLAS FE-I4 pixel chip can be achieved.

physics.ins-det↗