arXiv subjects

Dazhi He

Publications and source records attributed to Dazhi He.

32 records · Page 2Linked to original sources

arXiv2024

Fluid Antenna Index Modulation for MIMO Systems: Robust Transmission and Low-Complexity Detection

The fluid antenna (FA) index modulation (IM)-enabled multiple-input multiple-output (MIMO) system, referred to as FA-IM, significantly enhances spectral efficiency (SE) compared to the conventional FA-assisted MIMO system. To improve robustness against the high spatial correlation among multiple activated ports of the fluid antenna, this paper proposes an innovative FA grouping-based IM (FAG-IM) system. A block grouping scheme is employed based on the spatial correlation model and the distribution structure of the ports. Then, a closed-form expression for the average bit error probability (ABEP) upper bound of the FAG-IM system is derived. To reduce the complexity of the receiver, the message passing architecture is incorporated into the FAG-IM system. Building on this, an efficient approximate message passing (AMP) detector, named structured AMP (S-AMP) detector, is proposed by exploiting the structural characteristics of the transmitted signals. Simulation results confirm that the proposed FAG-IM system significantly outperforms the existing FA-IM system in the presence of spatial correlation, achieving more robust transmission. Furthermore, it is demonstrated that the proposed low-complexity S-AMP detector not only reduces time complexity to a linear scale but also substantially improves bit error rate (BER) performance compared to the minimum mean square error (MMSE) detector, thereby enhancing the practical feasibility of the FAG-IM system.

cs.IT↗

arXiv2024

PAPR Reduction with Pre-chirp Selection for Affine Frequency Division Multiplexing

Affine frequency division multiplexing (AFDM) is a promising new multicarrier technique for high-mobility communications based on discrete affine Fourier transform (DAFT). By properly tuning two parameters in the DAFT module, the effective channel in the DAFT domain can completely circumvent path overlap, thereby constituting a full representation of delay-Doppler profile. However, AFDM has a crucial problem of high peak-to-average power ratio (PAPR), stemming from randomness of modulated symbols. To reduce the PAPR of AFDM, a novel algorithm named grouped pre-chirp selection (GPS) is proposed in this letter. The GPS varying the pre-chirp parameter across subcarrier groups in a non-enumerated manner and then selects the signal with the smallest PAPR among all candidate signals. We detail the operational procedures of the GPS algorithm, analyzing GPS from four aspects: PAPR performance, computational complexity, spectral efficiency, and bit error rate (BER) performance. Simulations indicate the effectiveness of the proposed GPS in reducing PAPR. At the cost of slight communication performance, AFDM with GPS can achieve better PAPR performance than orthogonal time frequency space (OTFS) while maintaining a lower modulation complexity.

cs.IT↗

arXiv2024

Sum Rate Maximization for Movable Antenna-Aided Downlink RSMA Systems

Rate splitting multiple access (RSMA) is regarded as a crucial and powerful physical layer (PHY) paradigm for next-generation communication systems. Particularly, users employ successive interference cancellation (SIC) to decode part of the interference while treating the remainder as noise. However, conventional RSMA systems rely on fixed-position antenna arrays, limiting their ability to fully exploit spatial diversity. This constraint reduces beamforming gain and significantly impairs RSMA performance. To address this problem, we propose a movable antenna (MA)-aided RSMA scheme that allows the antennas at the base station (BS) to dynamically adjust their positions. Our objective is to maximize the system sum rate of common and private messages by jointly optimizing the MA positions, beamforming matrix, and common rate allocation. To tackle the formulated non-convex problem, we apply fractional programming (FP) and develop an efficient two-stage, coarse-to-fine-grained searching (CFGS) algorithm to obtain high-quality solutions. Numerical results demonstrate that, with optimized antenna adjustments, the MA-enabled system achieves substantial performance and reliability improvements in RSMA over fixed-position antenna setups.

cs.IT↗

arXiv2024

Decentralized Hybrid Precoding for Massive MU-MIMO ISAC

Integrated sensing and communication (ISAC) is a very promising technology designed to provide both high rate communication capabilities and sensing capabilities. However, in Massive Multi User Multiple-Input Multiple-Output (Massive MU MIMO-ISAC) systems, the dense user access creates a serious multi-user interference (MUI) problem, leading to degradation of communication performance. To alleviate this problem, we propose a decentralized baseband processing (DBP) precoding method. We first model the MUI of dense user scenarios with minimizing Cramer-Rao bound (CRB) as an objective function.Hybrid precoding is an attractive ISAC technique, and hybrid precoding using Partially Connected Structures (PCS) can effectively reduce hardware cost and power consumption. We mitigate the MUI between dense users based on ThomlinsonHarashima Precoding (THP). We demonstrate the effectiveness of the proposed method through simulation experiments. Compared with the existing methods, it can effectively improve the communication data rates and energy efficiency in dense user access scenario, and reduce the hardware complexity of Massive MU MIMO-ISAC systems. The experimental results demonstrate the usefulness of our method for improving the MUI problem in ISAC systems for dense user access scenarios.

cs.IT↗

arXiv2024

Fluid Antenna Grouping Index Modulation Design for MIMO Systems

Index modulation (IM) significantly enhances the spectral efficiency of fluid antennas (FAs) enabled multiple-input multiple-output (MIMO) systems, which is named FA-IM. However, due to the dense distribution of ports on the FA, the wireless channel exhibits a high spatial correlation, leading to severe performance degradation in the existing FA-IM-assisted MIMO systems. To tackle this issue, this paper proposes a novel fluid antenna grouping index modulation (FA-GIM) scheme to mitigate the high correlation between the activated ports. Specifically, considering the characteristics of the FA two-dimensional (2D) surface structure and the spatially correlated channel model in FA-assisted MIMO systems, a block grouping method is adopted, where adjacent ports are assigned to the same group. Consequently, different groups independently perform port index selection and constellation symbol mapping, with only one port being activated within each group during each transmission interval. Then, a closed-form average bit error probability (ABEP) upper bound for the proposed scheme is derived. Numerical results show that, compared to state-of-the-art schemes, the proposed FA-GIM scheme consistently achieves significant bit error rate (BER) performance gains under various conditions. The proposed scheme is both efficient and robust, enhancing the performance of FA-assisted MIMO systems.

cs.IT↗

arXiv2024

Deep joint source-channel coding for wireless point cloud transmission

The growing demand for high-quality point cloud transmission over wireless networks presents significant challenges, primarily due to the large data sizes and the need for efficient encoding techniques. In response to these challenges, we introduce a novel system named Deep Point Cloud Semantic Transmission (PCST), designed for end-to-end wireless point cloud transmission. Our approach employs a progressive resampling framework using sparse convolution to project point cloud data into a semantic latent space. These semantic features are subsequently encoded through a deep joint source-channel (JSCC) encoder, generating the channel-input sequence. To enhance transmission efficiency, we use an adaptive entropy-based approach to assess the importance of each semantic feature, allowing transmission lengths to vary according to their predicted entropy. PCST is robust across diverse Signal-to-Noise Ratio (SNR) levels and supports an adjustable rate-distortion (RD) trade-off, ensuring flexible and efficient transmission. Experimental results indicate that PCST significantly outperforms traditional separate source-channel coding (SSCC) schemes, delivering superior reconstruction quality while achieving over a 50% reduction in bandwidth usage.

cs.MM↗

arXiv2024

RIS-Aided Receive Generalized Spatial Modulation Design with Reflecting Modulation

Spatial modulation (SM) transmits additional information bits by the selection of antennas. Generalized spatial modulation (GSM), as an advanced type of SM, can be divided into diversity and multiplexing (MUX) schemes according to the symbols carried on the selected antennas are identical or different. Recently, reconfigurable intelligent surface (RIS) assisted SM exhibits better reception performance compared to conventional SM. To overcome the limitations of SM, this paper combines GSM with RIS and proposes the RIS-aided receive generalized spatial modulation (RIS-RGSM) scheme. The RIS-RGSM diversity scheme is realized via a simple improvement based on the state-of-the-art scheme. To further increase the transmission rate, a novel RIS-RGSM MUX scheme is proposed, where the reflection phase shifts and on/off states of RIS elements are configured to achieve bit mapping. The theoretical bit error rate (BER) of the proposed scheme is derived and agrees well with the simulation results. Numerical simulations show that the RIS-RGSM MUX scheme has better BER performance than the diversity scheme. The proposed scheme can significantly increase the transmission rate and maintain good performance compared to the existing scheme under a limited number of antennas.

cs.IT↗

arXiv2023

Detecting Abrupt Change of Channel Covariance Matrix in IRS-Assisted Communication

The knowledge of channel covariance matrices is crucial to the design of intelligent reflecting surface (IRS) assisted communication. However, channel covariance matrices may change suddenly in practice. This letter focuses on the detection of the above change in IRS-assisted communication. Specifically, we consider the uplink communication system consisting of a single-antenna user (UE), an IRS, and a multi-antenna base station (BS). We first categorize two types of channel covariance matrix changes based on their impact on system design: Type I change, which denotes the change in the BS receive covariance matrix, and Type II change, which denotes the change in the IRS transmit/receive covariance matrix. Secondly, a powerful method is proposed to detect whether a Type I change occurs, a Type II change occurs, or no change occurs. The effectiveness of our proposed scheme is verified by numerical results.

eess.SP↗

arXiv2023

Capacity-based Spatial Modulation Constellation and Pre-scaling Design

Spatial Modulation (SM) can utilize the index of the transmit antenna (TA) to transmit additional information. In this paper, to improve the performance of SM, a non-uniform constellation (NUC) and pre-scaling coefficients optimization design scheme is proposed. The bit-interleaved coded modulation (BICM) capacity calculation formula of SM system is firstly derived. The constellation and pre-scaling coefficients are optimized by maximizing the BICM capacity without channel state information (CSI) feedback. Optimization results are given for the multiple-input-single-output (MISO) system with Rayleigh channel. Simulation result shows the proposed scheme provides a meaningful performance gain compared to conventional SM system without CSI feedback. The proposed optimization design scheme can be a promising technology for future 6G to achieve high-efficiency.

cs.IT↗

arXiv2023

CDDM: Channel Denoising Diffusion Models for Wireless Semantic Communications

Diffusion models (DM) can gradually learn to remove noise, which have been widely used in artificial intelligence generated content (AIGC) in recent years. The property of DM for eliminating noise leads us to wonder whether DM can be applied to wireless communications to help the receiver mitigate the channel noise. To address this, we propose channel denoising diffusion models (CDDM) for semantic communications over wireless channels in this paper. CDDM can be applied as a new physical layer module after the channel equalization to learn the distribution of the channel input signal, and then utilizes this learned knowledge to remove the channel noise. We derive corresponding training and sampling algorithms of CDDM according to the forward diffusion process specially designed to adapt the channel models and theoretically prove that the well-trained CDDM can effectively reduce the conditional entropy of the received signal under small sampling steps. Moreover, we apply CDDM to a semantic communications system based on joint source-channel coding (JSCC) for image transmission. Extensive experimental results demonstrate that CDDM can further reduce the mean square error (MSE) after minimum mean square error (MMSE) equalizer, and the joint CDDM and JSCC system achieves better performance than the JSCC system and the traditional JPEG2000 with low-density parity-check (LDPC) code approach.

cs.IT↗

arXiv2023

NB-IoT Uplink Synchronization by Change Point Detection of Phase Series in NTNs

Non-Terrestrial Networks (NTNs) are widely recognized as a potential solution to achieve ubiquitous connections of Narrow Bandwidth Internet of Things (NB-IoT). In order to adopt NTNs in NB-IoT, one of the main challenges is the uplink synchronization of Narrowband Physical Random Access procedure which refers to the estimation of time of arrival (ToA) and carrier frequency offset (CFO). Due to the large propagation delay and Doppler shift in NTNs, traditional estimation methods for Terrestrial Networks (TNs) can not be applied in NTNs directly. In this context, we design a two stage ToA and CFO estimation scheme including coarse estimation and fine estimation based on abrupt change point detection (CPD) of phase series with machine learning. Our method achieves high estimation accuracy of ToA and CFO under the low signal-noise ratio (SNR) and large Doppler shift conditions and extends the estimation range without enhancing Random Access preambles.

cs.IT↗

arXiv2023

CDDM: Channel Denoising Diffusion Models for Wireless Communications

Diffusion models (DM) can gradually learn to remove noise, which have been widely used in artificial intelligence generated content (AIGC) in recent years. The property of DM for removing noise leads us to wonder whether DM can be applied to wireless communications to help the receiver eliminate the channel noise. To address this, we propose channel denoising diffusion models (CDDM) for wireless communications in this paper. CDDM can be applied as a new physical layer module after the channel equalization to learn the distribution of the channel input signal, and then utilizes this learned knowledge to remove the channel noise. We design corresponding training and sampling algorithms for the forward diffusion process and the reverse sampling process of CDDM. Moreover, we apply CDDM to a semantic communications system based on joint source-channel coding (JSCC). Experimental results demonstrate that CDDM can further reduce the mean square error (MSE) after minimum mean square error (MMSE) equalizer, and the joint CDDM and JSCC system achieves better performance than the JSCC system and the traditional JPEG2000 with low-density parity-check (LDPC) code approach.

cs.IT↗

arXiv2023

Detecting Abrupt Changes in Channel Covariance Matrix for MIMO Communication

The acquisition of the channel covariance matrix is of paramount importance to many strategies in multiple-input-multiple-output (MIMO) communications, such as the minimum mean-square error (MMSE) channel estimation. Therefore, plenty of efficient channel covariance matrix estimation schemes have been proposed in the literature. However, an abrupt change in the channel covariance matrix may happen occasionally in practice due to the change in the scattering environment and the user location. Our paper aims to adopt the classic change detection theory to detect the change in the channel covariance matrix as accurately and quickly as possible such that the new covariance matrix can be re-estimated in time. Specifically, this paper first considers the technique of on-line change detection (also known as quickest/sequential change detection), where we need to detect whether a change in the channel covariance matrix occurs at each channel coherence time interval. Next, because the complexity of detecting the change in a high-dimension covariance matrix at each coherence time interval is too high, we devise a low-complexity off-line strategy in massive MIMO systems, where change detection is merely performed at the last channel coherence time interval of a given time period. Numerical results show that our proposed on-line and off-line schemes can detect the channel covariance change with a small delay and a low false alarm rate. Therefore, our paper theoretically and numerically verifies the feasibility of detecting the channel covariance change accurately and quickly in practice.

eess.SP↗

arXiv2021

Detection of Abrupt Change in Channel Covariance Matrix for Multi-Antenna Communication

The knowledge of channel covariance matrices is of paramount importance to the estimation of instantaneous channels and the design of beamforming vectors in multi-antenna systems. In practice, an abrupt change in channel covariance matrices may occur due to the change in the environment and the user location. Although several works have proposed efficient algorithms to estimate the channel covariance matrices after any change occurs, how to detect such a change accurately and quickly is still an open problem in the literature. In this paper, we focus on channel covariance change detection between a multi-antenna base station (BS) and a single-antenna user equipment (UE). To provide theoretical performance limit, we first propose a genie-aided change detector based on the log-likelihood ratio (LLR) test assuming the channel covariance matrix after change is known, and characterize the corresponding missed detection and false alarm probabilities. Then, this paper considers the practical case where the channel covariance matrix after change is unknown. The maximum likelihood (ML) estimation technique is used to predict the covariance matrix based on the received pilot signals over a certain number of coherence blocks, building upon which the LLR-based change detector is employed. Numerical results show that our proposed scheme can detect the change with low error probability even when the number of channel samples is small such that the estimation of the covariance matrix is not that accurate. This result verifies the possibility to detect the channel covariance change both accurately and quickly in practice.

eess.SP↗