arXiv subjects

Deli Qiao

Publications and source records attributed to Deli Qiao.

At least 19 recordsLinked to original sources

arXiv2024

Energy Efficiency Analysis of IRS-aided Wireless Communication Systems Under Statistical QoS Constraints: An Information-Theoretic Perspective

This paper investigates the information-theoretic energy efficiency of intelligent reflecting surface (IRS)-aided wireless communication systems, taking into account the statistical quality-of-service (QoS) constraints on delay violation probabilities. Specifically, effective capacity is adopted to capture the maximum constant arrival rate that can be supported by a time-varying service process while fulfilling these statistical QoS requirements. We derive the minimum bit energy required for the IRS-aided wireless communication system under QoS constraints and analyze the spectral efficiency and energy efficiency tradeoff at low but nonzero signal-to-noise ratio (SNR) levels by also characterizing the wideband slope values. Our analysis demonstrates that the energy efficiency for the considered system under statistical QoS constraints can approach that for a system without QoS limitations in the low-SNR regime. Additionally, deploying a sufficiently large number of practical IRS reflecting elements can substantially reduce energy consumption required to achieve desired spectral efficiency performance in the low-power regime, even with limited bit-resolution phase shifters. Besides, we reveal that compared with the results applied to the low-power regime, higher effective capacity performance can be achieved in scenarios with sparse multipath fading while achieving the same minimum bit energy in the wideband regime.

cs.IT↗

arXiv2023

Delay-aware Multiple Access Design for Intelligent Reflecting Surface Aided Uplink Transmission

In this paper, we develop a hybrid multiple access (MA) protocol for an intelligent reflecting surface (IRS) aided uplink transmission network by incorporating the IRS-aided time-division MA (I-TDMA) protocol and the IRS-aided non-orthogonal MA (I-NOMA) protocol as special cases. Two typical communication scenarios, namely the transmit power limited case and the transmit energy limited case are considered, where the device's rearranged order, time and power allocation, as well as dynamic IRS beamforming patterns over time are jointly optimized to minimize the sum transmission delay. To shed light on the superiority of the proposed IRS-aided hybrid MA (I-HMA) protocol over conventional protocols, the conditions under which I-HMA outperforms I-TDMA and I-NOMA are revealed by characterizing their corresponding optimal solution. Then, a computationally efficient algorithm is proposed to obtain the high-quality solution to the corresponding optimization problems. Simulation results validate our theoretical findings, demonstrate the superiority of the proposed design, and draw some useful insights. Specifically, it is found that the proposed protocol can significantly reduce the sum transmission delay by combining the additional gain of dynamic IRS beamforming with the high spectral efficiency of NOMA, which thus reveals that integrating IRS into the proposed HMA protocol is an effective solution for delay-aware optimization. Furthermore, it reveals that the proposed design reduces the time consumption not only from the system-centric view, but also from the device-centric view.

cs.IT↗

arXiv2022

How to Minimize the Weighted Sum AoI in Multi-Source Status Update Systems: OMA or NOMA?

In this paper, the minimization of the weighted sum average age of information (AoI) in a multi-source status update communication system is studied. Multiple independent sources send update packets to a common destination node in a time-slotted manner under the limit of maximum retransmission rounds. Different multiple access schemes, i.e., orthogonal multiple access (OMA) and non-orthogonal multiple access (NOMA) are exploited here over a block-fading multiple access channel (MAC). Constrained Markov decision process (CMDP) problems are formulated to describe the AoI minimization problems considering both transmission schemes. The Lagrangian method is utilised to convert CMDP problems to unconstraint Markov decision process (MDP) problems and corresponding algorithms to derive the power allocation policies are obtained. On the other hand, for the case of unknown environments, two online reinforcement learning approaches considering both multiple access schemes are proposed to achieve near-optimal age performance. Numerical simulations validate the improvement of the proposed policy in terms of weighted sum AoI compared to the fixed power transmission policy, and illustrate that NOMA is more favorable in case of larger packet size.

cs.IT↗

arXiv2022

Throughput Maximization for Active Intelligent Reflecting Surface Aided Wireless Powered Communications

This paper considers an active intelligent reflecting surface (IRS)-aided wireless powered communication network (WPCN), where devices first harvest energy and then transmit information to a hybrid access point (HAP). Different from the existing works on passive IRS-aided WPCNs, this is the first work that introduces the active IRS in WPCNs. To guarantee fairness, the problem is formulated as an amplifying power-limited weighted sum throughput (WST) maximization problem, which is solved by successive convex approximation technique and fractional programming alternatively. To balance the performance and complexity tradeoff, three beamforming setups are considered at the active IRS, namely user-adaptive IRS beamforming, uplink-adaptive IRS beamforming, and static IRS beamforming. Numerical results demonstrate the significant superiority of employing active IRS in WPCNs and the benefits of dynamic IRS beamforming. Specifically, it is found that compared to the passive IRS, the active IRS not only improves the WST greatly, but also is more energy-efficient and can significantly extend the transmission coverage. Moreover, different from the symmetric deployment strategy of passive IRS, it is more preferable to deploy the active IRS near the devices.

cs.IT↗

arXiv2021

Energy Minimization for IRS-aided WPCNs with Non-linear Energy Harvesting Model

This paper considers an intelligent reflecting surface(IRS)-aided wireless powered communication network (WPCN), where devices first harvest energy from a power station (PS) in the downlink (DL) and then transmit information using non-orthogonal multiple access (NOMA) to a data sink in the uplink (UL). However, most existing works on WPCNs adopted the simplified linear energy-harvesting model and also cannot guarantee strict user quality-of-service requirements. To address these issues, we aim to minimize the total transmit energy consumption at the PS by jointly optimizing the resource allocation and IRS phase shifts over time, subject to the minimum throughput requirements of all devices. The formulated problem is decomposed into two subproblems, and solved iteratively in an alternative manner by employing difference of convex functions programming, successive convex approximation, and penalty-based algorithm. Numerical results demonstrate the significant performance gains achieved by the proposed algorithm over benchmark schemes and reveal the benefits of integrating IRS into WPCNs. In particular, employing different IRS phase shifts over UL and DL outperforms the case with static IRS beamforming.

cs.IT↗

arXiv2020

Joint Beamforming Design for IRS-Aided Communications with Channel Estimation Errors

This paper investigates the joint design of the beamforming scheme in intelligent reflecting surface (IRS) assisted multiuser (MU) multiple-input multiple-output (MIMO) downlink transmissions. Channel estimation errors associated with the minimum mean square error (MMSE) estimation are assumed and the weighted sum rate (WSR) is adopted as the performance metric. Low-resolution phase shifters (PSs) in practical implementations are taken into account as well. Under the constraint of the transmit power and discrete phase shifters (PSs), an optimization problem is formulated to maximize the WSR of all users. To obtain the optimal beamforming matrices at the IRS, two solutions based on the majorization-minimization (MM) and successive convex approximation (SCA) methods, respectively, are proposed. Through simulation results, both of the proposed two schemes achieve a significant improvement in WSR. Furthermore, the superiority of the SCA-based solution is demonstrated. Overall, two viable solutions to the joint beamforming design in IRS-aided MU-MIMO downlink communication systems with channel estimation errors are provided.

cs.IT↗

arXiv2020

Mimicking Full-Duplex Secure Communications for Buffer-Aided Multi-Relay Systems

This paper considers secure communication in buffer-aided cooperative wireless networks in the presence of one eavesdropper, which can intercept the data transmission from both the source and relay nodes. A new max-ratio relaying protocol is proposed, in which different relays are chosen for reception and transmission according to the ratio of the legitimate channels to the eavesdropper channels, so that the relay selected for reception and the relay selected for transmission can receive and transmit at the same time. It is worth noting that the relay employs a randomize-and-forward (RF) strategy such that the eavesdropper can only decode the signals received in the two hops independently. Theoretical analysis of the secrecy throughput of the proposed scheme is provided and the approximate closed-form expressions are derived, which are verified by simulations. Through numerical results, it is shown that the proposed scheme achieves a significant improvement in secrecy throughput compared with existing relay selection policies.

cs.IT↗

arXiv2020

Alternate Distributed Beamforming for Buffer-Aided Multi-Antenna Relay Systems

In this paper, link selection is investigated in half-duplex (HD) dual-hop cooperative systems with multiple antennas at the relays. Alternate distributed beamforming (ADB) scheme is revisited for buffer-aided multi-antenna relay systems, in which the relays are divided into two groups, with one group receiving the same information broadcast from the source and the other group transmitting the common messages to the destination via distributed beamforming in each time slot. It is worth noting that the relays used for reception and transmission are determined without the need of instantaneous channel state information (CSI). Theoretical analysis of the achievable throughput of the proposed scheme in Rayleigh fading is provided and the approximate closed-form expressions are derived. Simulation results are given to verify the theoretical analysis. Through numerical results, it is shown that compared with existing link selection policies, the fixed scheduling ADB scheme achieves a significant improvement in achievable throughput. It is also shown that for the ADB scheme, the throughput performance of increasing the number of antennas equipped at each relay is better than that of increasing the number of relays equipped with a single antenna when the total number of antennas at the relays is fixed.

cs.IT↗

arXiv2020

Age-Energy Tradeoff in Fading Channels with Packet-Based Transmissions

The optimal transmission strategy to minimize the weighted combination of age of information (AoI) and total energy consumption is studied in this paper. It is assumed that the status update information is obtained and transmitted at fixed rate over a Rayleigh fading channel in a packet-based wireless communication system. A maximum transmission round on each packet is enforced to guarantee certain reliability of the update packets. Given fixed average transmission power, the age-energy tradeoff can be formulated as a constrained Markov decision process (CMDP) problem considering the sensing power consumption as well. Employing the Lagrangian relaxation, the CMDP problem is transformed into a Markov decision process (MDP) problem. An algorithm is proposed to obtain the optimal power allocation policy. Through simulation results, it is shown that both age and energy efficiency can be improved by the proposed optimal policy compared with two benchmark schemes. Also, age can be effectively reduced at the expense of higher energy cost, and more emphasis on energy consumption leads to higher average age at the same energy efficiency. Overall, the tradeoff between average age and energy efficiency is identified.

cs.IT↗

arXiv2019

Alternate Distributed Beamforming for Decode-and-Forward Multi-Relay Systems Using Buffers

In this paper, link selection for half-duplex buffer-aided relay systems is revisited. A new fixed scheduling policy referred as alternate distributed beamforming (ADB) is proposed, in which the relays are divided into two groups, with one group receiving the same information broadcast from the source and the other group transmitting the common messages to the destination via distributed beamforming in each time slot. It is worth noting that the relays used for reception and transmission are determined without the need of instantaneous channel state information (CSI). Theoretical analysis of the achievable throughput of the proposed scheme in Rayleigh fading is provided and the approximate closed-form expressions are derived. Through numerical results, it is shown that compared with existing link selection policies, the proposed fixed scheduling ADB achieves a significant improvement in achievable throughput.

cs.IT↗

arXiv2019

Age-Optimal Power Control for Status Update Systems with Packet Based Transmissions

This paper investigates the average age of information (AoI) minimization in status update systems in which the update packets are transmitted with fixed rate. It is assumed that the source avoids queue-induced delay by generating and sending a new status update packet in each time slot. Assuming that the transmit power can be adapted based on the number of successive NACKs (negative acknowledgements) received, a closed-form expression for the average AoI is derived considering transmissions over block fading channel models. An optimization problem for minimizing the average AoI under average power constraints is formulated and a stochastic optimization algorithm for obtaining a feasible solution is proposed. Numerical results on the proposed power control policy show that more power is preferred to be allocated to packets after a certain number of failure packets in the low-power regime and the proposed power control reduces the average AoI compared to the constant power policy. An alternative on-off power control policy is also proposed and shown to achieve satisfactory performance.

cs.IT↗

arXiv2019

Outage Analysis of Heterogeneous mmWave Cellular Networks Employing JSDM

In this paper, the outage performance of a two-tier heterogeneous mmWave cellular networks employing joint spatial division and multiplexing (JSDM) is investigated. It is assumed that macro base stations (BSs) equipped with a large number of antennas and pico BSs equipped with single antenna serve users simultaneously. The two-tier BSs and users are distributed according to independent Poisson point processes (PPPs). Theoretical analysis of the signal-to-interference-plus-noise ratio (SINR) outage probability of the typical user is first provided. The all SINR outage probability of the two tiers is then derived. Simulation results in accordance with theoretical analysis demonstrating the performance improvement of two-tier networks compare with the single-tier network are provided. By using the noise-limited assumption for mmWave networks, a simpler expression to analyze the outage performance is obtained.

eess.SP↗

arXiv2018

Space-Time Block Coding Based Beamforming for Beam Squint Compensation

In this paper, the beam squint problem, which causes significant variations in radiated beam gain over frequencies in millimeter wave communication system, is investigated. A constant modulus beamformer design, which is formulated to maximize the expected average beam gain within the bandwidth with limited variation over frequencies within the bandwidth, is proposed. A semidefinite relaxation (SDR) method is developed to solve the optimization problem under the constant modulus constraints. Depending on the eigenvalues of the optimal solution, either direct beamforming or transmit diversity based beamforming is employed for data transmissions. Through numerical results, the proposed transmission scheme can compensate for beam squint effectively and improve system throughput. Overall, a transmission scheme for beam squint compensation in wideband wireless communication systems is provided.

cs.IT↗

arXiv2018

Performance Analysis of Indoor THz Communications with One-Bit Precoding

In this paper, the performance of indoor Terahertz (THz) communication systems with one-bit digital-to-analog converters (DACs) is investigated. Array-of-subarrays architecture is assumed for the antennas at the access points, where each RF chain uniquely activates a disjoint subset of antennas, each of which is connected to an exclusive phase shifter. Hybrid precoding, including maximum ratio transmission (MRT) and zero-forcing (ZF) precoding, is considered. The best beamsteering direction for the phase shifter in the large subarray antenna regime is first proved to be the direction of the line-of-sight (LOS) path. Subsequently, the closed-form expression of the lower-bound of the achievable rate in the large subarray antenna regime is derived, which is the same for both MRT and ZF and is independent of the transmit power. Numerical results validating the analysis are provided as well.

cs.IT↗

arXiv2018

Outage Analysis of Relay-Assisted mmWave Cellular Systems Employing JSDM

In this paper, the outage performance of relay-assisted millimeter wave (mmWave) cellular systems employing joint spatial division and multiplexing (JSDM) is investigated. It is assumed that the macro base station (BS) equipped with a large number of antennas serves the single antenna pico BS (as a relay) and users simultaneously, and that the pico BS is located at the edge of the macro cell. Theoretical analysis of the signal-to-interference-plus-noise ratio (SINR) outage probability of each user is first obtained. The cell SINR outage probability is then derived. Under the noise-limited assumption, simplified closed-form expressions of the outage probability are given as well. Simulation results demonstrating the performance improvement due to the relay introduced by the pico BS are provided. Overall, the impact of deploying pico BS as a relay in the mmWave cellular systems is characterized.

cs.IT↗

arXiv2016

Outage Effective Capacity of Buffer-Aided Diamond Relay Systems Using HARQ with Incremental Redundancy

In this paper, transmission over buffer-aided diamond relay systems under statistical quality of service (QoS) constraints is studied. The statistical QoS constraints are imposed as limitations on delay violation probabilities. In the absence of channel state information (CSI) at the transmitter, truncated hybrid automatic repeat request-incremental redundancy (HARQ-IR) is incorporated to make better use of the wireless channel and the resources for each communication link. The packets that cannot be successfully received upon the maximum number of transmissions will be removed from buffer, i.e., outage occurs. The \emph{outage effective capacity} of a communication link is defined as the maximum constant arrival rate to the source that can be supported by the \emph{goodput} departure processes, i.e., the departure that can be successfully received by the receiver. Then, the outage effective capacity for the buffer-aided diamond relay system is obtained for HARQ-IR incorporated transmission strategy under the \emph{end-to-end} delay constraints. In comparison with the DF protocol with perfect CSI at the transmitters, it is shown that HARQ-IR can achieve superior performance when the SNR levels at the relay are not so large or when the delay constraints are stringent.

cs.IT↗

arXiv2016

Statistical Delay Tradeoffs in Buffer-Aided Two-Hop Wireless Communication Systems

This paper analyzes the impact of statistical delay constraints on the achievable rate of a two-hop wireless communication link, in which the communication between a source and a destination is accomplished via a buffer-aided relay node. It is assumed that there is no direct link between the source and the destination, and the buffer-aided relay forwards the information to the destination by employing the decode-and-forward scheme. Given statistical delay constraints specified via maximum delay and delay violation probability, the tradeoff between the statistical delay constraints imposed on any two concatenated queues is identified. With this characterization, the maximum constant arrival rates that can be supported by this two-hop link are obtained by determining the effective capacity of such links as a function of the statistical delay constraints, signal-to-noise ratios (SNR) at the source and relay, and the fading distributions of the links. It is shown that asymmetric statistical delay constraints at the buffers of the source and relay node can improve the achievable rate. Overall, the impact of the statistical delay tradeoff on the achievable throughput is provided.

cs.IT↗

arXiv2016

Single-Carrier Modulation for Large-Scale Antenna Systems

Large-scale antenna (LSA) has gained a lot of attention due to its great potential to significantly improve system throughput. In most existing works on LSA systems, orthogonal frequency division multiplexing (OFDM) is presumed to deal with frequency selectivity of wireless channels. Although LSA-OFDM is a natural evolution from multiple-input multiple-output OFDM (MIMO-OFDM), the drawbacks of LSA-OFDM are inevitable, especially when used for the uplink. In this paper, we investigate single-carrier (SC) modulation for the uplink transmission in LSA systems based on a novel waveform recovery theory, where the receiver is designed to recover the transmit waveform while the information-bearing symbols can be recovered by directly sampling the recovered waveform. The waveform recovery adopts the assumption that the antenna number is infinite and the channels at different antennas are independent. In practical environments, however, the antenna number is always finite and the channels at different antennas are also correlated when placing hundreds of antennas in a small area. Therefore, we will also analyze the impacts of such non-ideal environments.

cs.IT↗