arXiv subjects

Dominyka Stonyte

Publications and source records attributed to Dominyka Stonyte.

4 recordsLinked to original sources

arXiv2026

High Entropy Alloy under Shock Compression: Optical-Pump X-Ray-Probe

High entropy alloys (HEAs) are multi-principal-element alloys designed for tailorable mechanical performance and have been attracting significant engineering interest, yet their fundamental behaviour under extreme dynamic conditions, such as shock loading, remains unexplored. Here, we report laser-shock experiments on two different types of 1-micrometers-thick HEA microfilms, CuPdAgPtAu and CrFeCoNiCuMo, on 25-micrometers-thick black-Kapton ablator driven by a high intensity laser pulse (532 nm, 5 ns, 16 J, 0.5-mm diameter focal spot) and probed by an X-ray free electron laser (XFEL) pulse (12 keV, 7 fs). Time-resolved X-ray diffraction (XRD) shows the formation of a transient phase with a lattice compression up to 5.1% of the CuPdAgPtAu HEA along the (111) plane; this transient compressed phase existed for 0.3 ns. The impedance matching Hugoniot analysis estimated a shock pressure of 55 +/- 6 GPa in the HEA film, while Au- and Fe-based equations of state (EoS) modelling predict 80 GPa (0.8 MBar) at the free HEA surface. The free HEA surface reached maximum velocities of ~ 5 km/s as recorded from in situ monitoring with the velocity interferometry system for any reflector (VISAR) imaging. These initial HEA results show the suitability of HEA sample preparation and XFEL-based XRD characterisation under extreme shock loading, and are promising for experimental determination of the EoS of this emerging class of materials (beamtime proposal No.: 2024A8503 for a 6-hour preliminary experiment).

cond-mat.mtrl-sci↗

arXiv2025

Ablation of black-Si by (Gauss-)Bessel femtosecond laser beams

Laser machining and modification of black-Si (b-Si) by femtosecond laser Gaussian (G-) and Gauss-Bessel (GB-) beams are compared at a wavelength of 1030 nm. The GB-beam was generated using a diffractive axicon lens and 10x demagnification optics. It was found that modification of b-Si well below (a factor 50x) the single pulse ablation fluence of 0.2 J/cm2 was possible, corresponding to ablation/melting of nano-needles. The width of modification was almost independent of pulse energy/fluence and had a width of 1/e2-intensity profile at the melting regime. For the GB-beam, the smallest width of laser modification at 0.2 J/cm2 threshold (at the center core) was close to the FWHM of the core of the GB-beam. The aspect ratio of the ablated groove on the surface of b-Si made by GB-beam was twice as large - up to 8 - compared to that achievable with G-beam, and it was at a lower fluence of 4 J/cm2 (50x reduction). Reflectivity of two-side nanotextured b-Si on plasma-thinned 70-micrometers thick Si was strongly reduced in the near-IR range, reaching transmittance >95% at 1.7-2.1 micrometres wavelengths.

physics.optics↗

arXiv2024

3D Free-Form Optical Lens -- Miniaturised Fibre Couplers for Astrophotonics

In astronomy, multi-object spectrographs employ fibre positioning robots to couple the light from multiple astronomy sources (stars or galaxies) into multiple multi-mode fibres, which are distributed across the focal plane of the telescope. These fibres transport the celestial light to the entrance slit of a spectrograph (or bank of spectrographs) for analysis. For any multi-object system mm-scale opto-mechanical solutions are required to couple the telescope light efficiently into the fibre. We demonstrate a unique micro-optics solution to replace current optical fibre couplers. Specifically, we target technology on board the Keck telescope's FOBOS - Fibre-Optic Broadband Optical Spectrograph - which operates at UV to IR spectral ranges. For spectrally broad UV-IR band operation we use glass and crystals: fused silica, crystalline quartz (transparency 0.16 - 2 micrometers), sapphire Al2O3 (0.2 - 5 micrometers), CaF2 (0.2-7 micrometers), and BaF2 (0.2-10 micrometers). The miniaturised micro-coupler is monolithic, with the entire light path contained within glass or crystal, seamlessly extending to the fibre entrance, which is laser-machined and precisely aligned with the optical axis.

astro-ph.IM↗

arXiv2024

Bessel-beam direct-write of the etch-mask in a nano-film of alumina for high-efficiency Si solar cells

Large surface area applications such as high-efficiency > 26% solar cells require surface patterning with 1-10 micrometers periodic patterns at high fidelity over 1-10 cm^2 areas (before up scaling to 1 m^2) to perform at, or exceed, the Lambertian (ray optics) limit of light trapping. Here we show a pathway to high-resolution sub-1 micrometer etch mask patterning by ablation using direct femtosecond laser writing performed at room conditions (without the need for a vacuum-based lithography approach). A Bessel beam was used to alleviate the required high surface tracking tolerance for ablation of 0.3-0.8 micrometer diameter holes in ~40 nm alumina Al2O3-mask at high writing speed, 7.5 cm/s; a patterning rate 1 cm^2 per 20 min. The plasma etching protocol was optimised for a zero-mesa formation of photonic crystal (PhC) trapping structures and smooth surfaces at the nanoscale level. Scaling up in area and throughput of the demonstrated approach is outlined.

physics.optics↗