arXiv subjects

Douglas S. Galvao

Publications and source records attributed to Douglas S. Galvao.

At least 55 records · Page 3Linked to original sources

arXiv2021

Mechanical Response of Pentadiamond: A DFT and Molecular Dynamics Study

Pentadiamond is a recently proposed new carbon allotrope consisting of a network of pentagonal rings where both sp$^2$ and sp$^3$ hybridization are present. In this work we investigated the mechanical and electronic properties, as well as, the thermal stability of pentadiamond using DFT and fully atomistic reactive molecular dynamics (MD) simulations. We also investigated its properties beyond the elastic regime for three different deformation modes: compression, tensile and shear. The behavior of pentadiamond under compressive deformation showed strong fluctuations in the atomic positions which are responsible for the strain softening at strains beyond the linear regime, which characterizes the plastic flow. As we increase temperature, as expected, Young's modulus values decrease, but this variation (up to 300 K) is smaller than 10\% (from 347.5 to 313.6 GPa), but the fracture strain is very sensitive, varying from $\sim$44\% at 1K to $\sim$5\% at 300K.

cond-mat.mtrl-sci↗

arXiv2021

Effect of Oxygen and Aluminium Incorporation on Local Structure of GaN Nanowires: Insight from Extended X-ray Absorption Fine Structure Analysis

A thorough investigation of local structure, influencing macroscopic properties of the solid is of potential interest. We investigated the local structure of GaN nanowires (NWs) with different native defect concentration synthesized by the chemical vapor deposition technique. Extended X-ray absorption fine structure (EXAFS) analysis and semi-empirical and the density functional theory (DFT) calculations were used to address the effect of dopant incorporation along with other defects on the co-ordination number and bond length values. The decrease of the bond length values along preferential crystal axes in the local tetrahedral structure of GaN emphasizes the preferred lattice site for oxygen doping. The preferential bond length contraction is corroborated by the simulations. We have also studied the impact on the local atomic configuration of GaN NWs with Al incorporation. AlxGa1-xN NWs are synthesized via novel ion beam techniques of ion beam mixing and post-irradiation diffusion process. The change in the local tetrahedral structure of GaN with Al incorporation is investigated by EXAFS analysis. The analysis provides a clear understanding of choosing a suitable process for ternary III-nitride random alloy formation. The local structure study with the EXAFS analysis is corroborated with the observed macroscopic properties studied using Raman spectroscopy.

cond-mat.mtrl-sci↗

arXiv2020

Graphene-based Nanoscale version of da Vinci's Reciprocal Structures

A reciprocal structure (RS) is a mechanical resistant structure formed by a set of self-supporting elements satisfying certain conditions of structural reciprocity (SR) . The first condition is that each element of the structure has to support and be supported by the others. The second condition is that these functions cannot occur in the same part of the element. These two properties make beams and two-dimensional materials very much appropriate to build RSs. Commonly seen in floors or roofs, SR is also present in art, religious symbols and decorative objects. Da Vinci has drawn several examples of such RSs. Here, we propose a simple nano version of a da Vinci's RS based on graphene nanoribbons. The stability and resistance against mechanical impacts (ballistic projectile) were investigated through fully atomistic molecular dynamics (MD) simulations. We considered structures with three and four joins with and without RS topologies. Our MD results showed that structures with RS topologies are more impact resistant than those without SR, despite the fact that the used graphene nanoribbons are highly pliable. We discuss these results in terms of the number of joins, energy absorption and stress on the structures. We discuss possible applications in nanoengineering.

cond-mat.mtrl-sci↗

arXiv2020

A DFT Investigation of the Electronic and Optical Properties of Pentadiamond

Recently, a new carbon 3D carbon allotrope named pentadiamond was proposed. Pentadiamond is composed of carbon atoms in mixed sp$^2$ and sp$^3$-like hybridization. In this work, we have carried out a detailed investigation of the electronic and optical properties of pentadiamond structure using first-principles (DFT) methods. Our results show that pentadiamond has an indirect bandgap semiconductor of $2.50$ eV with GGA-PBE and $3.31$ eV with HSE06. Its static dielectric constant is $4.70$ and the static refractive index is $2.16$. Pentadiamond presents low reflectivity, almost 40$\%$, for all-optical spectrum, making it a good structure to be used as a UV collector. Also, pentadiamond exhibits optical activity in the UV range where other carbon allotropes, such as diamond and 8-tetra(2,2) tubulane show no activity.

cond-mat.mtrl-sci↗

arXiv2020

Optoelectronic Properties of Amorphous Carbon-Based Nanotube and Nanoscroll

Free-standing monolayer amorphous carbon (MAC) is a pure carbon structure composed of randomly distributed atom rings with different sizes, which was recently synthesized. In this work, we carried out ab initio and tight-binding calculations to investigate the optoelectronic properties of MAC and its derived nanotube and nanoscroll configurations. Our results show MAC, tube, and scrolls exhibit similar electronic behavior. All structures absorb from infrared to ultraviolet, with maximum absorption peaks the visible-ultra violet ($\sim 3.2$ eV). The maximum and minimum reflectivity values are in the range 0.3-0.5 (infrared) and 0.1-0.0 (ultraviolet), making these materials good candidates to ultraviolet filters.

cond-mat.mtrl-sci↗

arXiv2020

Thiophene-Tetrathia-Annulene monolayer (TTA-2D): A new 2D semiconductor material with indirect bandgap

We propose a new 2D semiconductor material (TTA-2D) based on the molecular structure of Thiophene-Tetrathia-Annulene (TTA). The TTA-2D structural, electronic, and optical properties were investigated using \textit{ab initio} methods. Our results show that TTA-2D is a small indirect bandgap semiconductor ($0.6$ eV). A semiconductor-metal transition can be induced by applying a uniaxial strain. Our results also show that TTA-2D is thermally stable up to $T=1000$ K. TTA-2D absorbs in a large spectral range, from infrared to ultraviolet regions. Values of refractive index and reflectivity show that TTA-2D reflects only $10\%$ of the incident light in the visible region. These results suggest that TTA-2D is a promising material for solar cell applications.

cond-mat.mtrl-sci↗

arXiv2020

Mechanical Properties of Diamond Schwarzites: From Molecular Dynamics Simulations to 3D Printing

Schwarzites are porous crystalline structures with Gaussian negative curvature. In this work, we investigated the mechanical behavior and energy absorption properties of two carbon-based diamond schwarzites (D688 and D8bal). We carried out fully atomistic molecular dynamics (MD) simulations. The optimized MD atomic models were used to generate macro-scale models for 3D-printing (PolyLactic Acid (PLA) polymer filaments) through Fused Deposition Modelling (FDM). Mechanical properties under uniaxial compression were investigated for both the atomic models and the 3D-printed ones. Mechanical testings were performed on the 3D-printed schwarzites where the deformation mechanisms were found to be similar to those observed in MD simulations. These results are suggestive of a scale-independent mechanical behavior that is dominated by structural topology. The structures exhibit high specific energy absorption and crush force efficiency ~0.8, which suggest that the 3D-printed diamond schwarzites are good candidates as energy-absorbing materials.

physics.app-ph↗

arXiv2020

On the Structural Stability and Optical Properties of Germanium-based Schwarzites: A Density Functional Theory Investigation

Since graphene was synthesized the interest for building new 2D and 3D structures based on the carbon allotropes has been growing every day. One of these 3D structures is know as carbon schwarzites. Schwarzites consist of carbon nanostructures possessing the shape of Triply-Periodic Minimal Surfaces (TPMS), which is characterized by a negative Gaussian curvature introduced by the presence of carbon rings with more than six atoms. Some examples of schwarzite families include: primitive (P), gyroid (G) and diamond (D). Previous studies considering different element species of schwarzites have investigated the mechanical, electrical and thermal properties. In this work, we investigated the stability of germanium (Ge) schwarzites using density functional theory with GGA exchange-correlation functional. We chose one structure of each family (P8bal), (G688) and (D688). It was observed that regions usually flat in carbon schwarzites acquires buckled configurations as previously observed on silicene and germanene monolayers. The investigated structures presented a semiconducting bandgap ranging from $0.13$ to $0.27$ eV. We also performed calculations of optical properties within the linear regime, where it was shown that Ge schwarzites structures absorb light from infrared to ultra-violet frequencies. Therefore, our results open new perspectives of materials that can be used in optelectronics devices application.

cond-mat.mtrl-sci↗

arXiv2020

Zeolite-inspired 3d printed structures with enhanced mechanical properties

Specific strength (strength/density) is a crucial factor while designing high load bearing architecture in areas of aerospace and defence. Strength of the material can be enhanced by blending with high strength component or, by compositing with high strength fillers but both the options has limitations such as at certain load, materials fail due to poor filler and matrix interactions. Therefore, researchers are interested in enhancing strength of materials by playing with topology/geometry and therefore nature is best option to mimic for structures whereas, complexity limits nature mimicked structures. In this paper, we have explored Zeolite-inspired structures for load bearing capacity. Zeolite-inspired structure were obtained from molecular dynamics simulation and then fabricated via Fused deposition Modeling. The atomic scale complex topology from simulation is experimentally synthesized using 3D printing. Compressibility of as-fabricated structures was tested in different direction and compared with simulation results. Such complex architecture can be used for ultralight aerospace and automotive parts.

physics.app-ph↗

arXiv2020

On the Mechanical and Thermal Stability of Free-standing Monolayer Amorphous Carbon

Recently (C.-T. Toh et al., Nature 577, 199 (2020)), the first synthesis of free-standing monolayer amorphous carbon (MAC) was achieved. MAC is a pure carbon structure composed of five, six, seven and eight atom rings randomly distributed. MAC proved to be surprisingly stable and highly fracture resistant. Its electronic properties are similar to boron nitride. In this work, we have investigated the mechanical properties and thermal stability of MAC models using fully-atomistic reactive molecular dynamics simulations. For comparison purposes, the results are contrasted against pristine graphene (PG) models of similar dimensions. Our results show that MAC and PG exhibit distinct mechanical behavior and fracture dynamics patterns. While PG after a critical strain threshold goes directly from elastic to brittle regimes, MAC shows different elastic stages between these two regimes. Remarkably, MAC is thermally stable up to 3600 K, which is close to the PG melting point. These exceptional physical properties make MAC-based materials promising candidates for new technologies, such as flexible electronics.

cond-mat.mtrl-sci↗

arXiv2020

Ballistic Properties of Highly Stretchable Graphene Kirigami Pyramid

Graphene kirigami (patterned cuts) can be an effective way to improve some of the graphene mechanical and electronic properties. In this work, we report the first study of the mechanical and ballistic behavior of single and multilayered graphene pyramid kirigami (GKP). We have carriedout fully atomistic reactive molecular dynamics simulations. GPK presents a unique kinetic energy absorption due to its topology that creates multi-steps dissipation mechanisms, which block crack propagation. Our results show that even having significantly less mass, GKP can outperform graphene structures with similar dimensions in terms of absorbing kinetic energy.

cond-mat.mtrl-sci↗

arXiv2020

Carbon Schwarzites Behavior Under Ballistic Impacts

Schwarzites are 3D crystalline porous materials exhibiting the shape of Triply Periodic Minimal Surfaces (TPMS). They possess negative Gaussian curvature, created by the presence of rings with more than six sp2-hybridized carbon atoms. Recently, new routes to their synthesis have been proposed. Due to its foam-like structure, schwarzites are interesting for mechanical energy absorption applications. In this work, we investigate through fully atomistic reactive molecular dynamics the mechanical response under ballistic impacts of four structures from primitive (P) and gyroid (G) families (two structures within each family). The two structures in the same family differ mainly by the ratio of hexagons to octagons, where this ratio increases the 'flatness' of the structures. Although the penetration depth values are higher in the 'flatter' structures (P8bal and G8bal), the absorbed kinetic energy by them is considerably higher, which yields them a better energy-absorption performance.

cond-mat.mtrl-sci↗

arXiv2020

Mechanical Properties of a Diamond Schwarzite: From Atomistic Models to 3D-Printed Structures

Triply Periodic Minimal Surfaces (TPMS) possess locally minimized surface area under the constraint of periodic boundary conditions. Different families of surfaces were obtained with different topologies satisfying such conditions. Examples of such families include Primitive (P), Gyroid (G) and Diamond (D) surfaces. From a purely mathematical subject, TPMS have been recently found in materials science as optimal geometries for structural applications. Proposed by Mackay and Terrones in 1991, schwarzites are 3D crystalline porous carbon nanocrystals exhibiting the shape of TPMS. Although their complex topology poses serious limitations on their synthesis with conventional nanoscale fabrication methods, such as Chemical Vapour Deposition (CVD), TPMS can be fabricated by Additive Manufacturing (AM) techniques, such as 3D Printing. In this work, we used an optimized atomic model of a schwarzite structure from the D family (D8bal) to generate a surface mesh that was subsequently used for 3D-printing through Fused Deposition Modelling (FDM). This D schwarzite was 3D-printed with thermoplastic PolyLactic Acid (PLA) polymer filaments. Mechanical properties under uniaxial compression were investigated for both the atomic model and the 3D-printed one. Fully atomistic Molecular Dynamics (MD) simulations were also carried out to investigate the uniaxial compression behavior of the D8bal atomic model. Mechanical testings were performed on the 3D-printed schwarzite where the deformation mechanisms were found to be similar to those observed in MD simulations. These results are suggestive of a scale-independent mechanical behavior that is dominated by structural topology.

physics.app-ph↗

arXiv2019

Three-dimensional carbon nanotube networks from beta zeolite templates: Thermal stability and mechanical properties

We here investigated the thermal and mechanical behaviors of three-dimensional beta zeolite-templated carbon nanotube networks (BZCN). These networks are topologically generated by inserting carbon nanotubes (CNTs) into zeolite channels and connecting them using X-type junctions. We considered two cases, one with the tubes filling all zeolite channels (HD-BZCN) and the other with just partial filling (LD-BZCN). Fully atomistic reactive molecular dynamics (MD) simulations show that the networks exhibit high thermal stability (up to 1000 K). When compressed, the structures can withstand very large strains without fracturing (>50% for HD-BZCN and >70% for LD-BZCN). LD-BZCN can be stretched over 100% without fracturing.

cond-mat.mtrl-sci↗

arXiv2019

New zero Poisson's ratio models

Most materials exhibit positive Poisson's ratio (PR) values but special structures can also present negative and, even rarer, zero (or close to zero) PR. Null PR structures have received much attention due to their unusual properties and potential applications in different fields, such as aeronautics and bio-engineering. Here, we present a new and simple near-zero PR 2D topological model based on a structural block composed of two smooth and rigid bars connected by a soft membrane or spring. It is not based on re-entrant or honeycomb-like configurations, which have been the basis of many null or quasi-null PR models. Our topological model was 3D printed and the experimentally obtained PR was$-0.003\,\pm 0.001\,$, which is one the closest to zero value ever reported. This topological model can be easily extended to 3D systems and with compression in any direction. The advantages and disadvantages of these models are also addressed.

cond-mat.mtrl-sci↗

arXiv2019

Mechanical and Energy-absorption Properties of Schwarzites

We investigated through fully atomistic molecular dynamics simulations, the mechanical behavior (compressive and tensile) and energy absorption properties of two families (primitive (P688 and P8bal) and gyroid (G688 and G8bal)) of carbon-based schwarzites. Our results show that all schwarzites can be compressed (with almost total elastic recovery) without fracture to more than 50%, one of them can be even remarkably compressed up to 80%. One of the structures (G8bal) presents negative Poisson's ratio value (auxetic behavior). The crush force efficiency, the stroke efficiency and the specific energy absorption (SEA) values show that schwarzites can be effective energy absorber materials. Although the same level of deformation without fracture observed in the compressive case is not observed for the tensile case, it is still very high (30-40%). The fracture dynamics show extensive structural reconstructions with the formation of linear atomic chains (LACs).

cond-mat.mtrl-sci↗

arXiv2018

Mechanical Properties of Protomene: A Molecular Dynamics Investigation

Recently, a new class of carbon allotrope called protomene was proposed. This new structure is composed of sp2 and sp3 carbon-bonds. Topologically, protomene can be considered as an sp3 carbon structure (~80% of this bond type) doped by sp2 carbons. First-principles simulations have shown that protomene presents an electronic bandgap of ~3.4 eV. However, up to now, its mechanical properties have not been investigated. In this work, we have investigated protomene mechanical behavior under tensile strain through fully atomistic reactive molecular dynamics simulations using the ReaxFF force field, as available in the LAMMPS code. At room temperature, our results show that the protomene is very stable and the obtained ultimate strength and ultimate stress indicates an anisotropic behavior. The highest ultimate strength was obtained for the x-direction, with a value of ~110 GPa. As for the ultimate strain, the highest one was for the z-direction (~25% of strain) before protomene mechanical fracture.

cond-mat.mtrl-sci↗

arXiv2018

Influence of Graphene Wettability on Spreading Patterns of Nanodroplets Impacting at High Speed

We report here a fully atomistic molecular dynamics study on the dynamics of impact of water nanodroplets (100 Å of diameter) at high velocities (from 1 up to 15 Å/ps) against graphene targets. Our results show that tuning graphene wettability (through parameter changes) significantly affects the structural and dynamical aspects of the nanodroplets. We identified three ranges of velocities with distinct characteristics, from simple deposition of the droplet to spreading with rebound, and finally droplet fragmentation. We also identify that in an intermediary velocity of 7 Å/ps, the pattern of spreading critically changes, due to formation of voids on droplet structure. These voids affect in a detrimental way the droplet spreading on the less hydrophilic surface, as it takes more time to the droplet recover from the spreading and to return to a semi-spherical configuration. When the velocity is increased to values larger than 11 Å/ps, the droplet fragments, which reveals the maximum possible spreading.

cond-mat.mtrl-sci↗