arXiv subjects

E. Ceccotti

Publications and source records attributed to E. Ceccotti.

18 recordsLinked to original sources

arXiv2025

The impact of lunar topography on the 21-cm power spectrum for grid-based arrays : Insights for the Dark-ages EXplorer (DEX)

The Dark Ages (DA) provides a crucial window into the physics of the infant Universe, with the 21-cm signal offering the only direct probe for mapping out the three-dimensional distribution of matter at this epoch. To measure this cosmological signal, the Dark-ages EXplorer (DEX) has been proposed as a compact, grid-based radio array on the lunar farside. The minimal design consists of a 32 $\times$ 32 array of 3-m dipole antennas, operating in the $7 - 50$ MHz band. A practical challenge on the lunar surface is that the antennas may get displaced from their intended positions due to deployment imprecisions and non-coplanarity arising from local surface undulations. We present, for the first time, an end-to-end simulation pipeline, called SPADE-21cm, that integrates a sky model with a DA 21-cm signal model simulated in the lunar frame and incorporating lunar topography data. We study the effects of both lateral (xy) and vertical (z) offsets on the two-dimensional power spectra across the $7 - 12$ MHz and $30 - 35$ MHz spectral windows, with tolerance thresholds derived only for the latter. Our results show that positional offsets bias the power spectrum by $10 - 30$ per cent relative to the expected 21-cm power spectrum during DA. Lateral offsets within $\sigma_{xy}/\lambda \lesssim 0.027$ (at 32.5 MHz) keep the fraction of Fourier modes with strong contamination (> 50 per cent of the signal) to less than 1 per cent, whereas vertical height offsets affect a larger fraction. This conclusion holds for the 21-cm window with $k_\parallel > 0.5$ $h$ cMpc$^{-1}$ over the range of $k_\perp = 0.003 - 0.009$ $h$ cMpc$^{-1}$.

astro-ph.IM↗

arXiv2025

Mitigating incoherent excess variance in high-redshift 21 cm observations with multi-output cross-Gaussian process regression

Systematic effects that limit the achievable sensitivity of current low-frequency radio telescopes to the 21 cm signal are among the foremost challenges in observational 21 cm cosmology. The standard approach to retrieving the 21 cm signal from radio interferometric data separates it from bright astrophysical foregrounds by exploiting their spectrally smooth nature, in contrast to the finer spectral structure of the 21 cm signal. Contaminants exhibiting rapid frequency fluctuations, on the other hand, are difficult to separate from the 21 cm signal using standard techniques, and the power from these contaminants contributes to low-level systematics that can limit our ability to detect the 21 cm signal. Many of these low-level systematics are incoherent across multiple nights of observation, resulting in an incoherent excess variance above the thermal noise sensitivity of the instrument. In this paper, we develop a method called cross-GPR (cross covariance Gaussian process regression) that exploits the incoherence of these systematics to separate them from the 21 cm signal, which remains coherent across multiple nights of observation. We first develop and demonstrate the technique on synthetic signals in a general setting, and then apply it to gridded interferometric visibility cubes. We perform realistic simulations of visibility cubes containing foregrounds, 21 cm signal, noise, and incoherent systematics. The simulations show that the method can successfully separate and subtract incoherent contributions to the excess variance, and its advantages over standard techniques become more evident when the spectral behavior of the contaminants resembles that of the 21 cm signal. Simulations performed on a variety of 21 cm signal shapes also reveal that the cross-GPR approach can subtract incoherent contributions to the excess variance, without suppressing the 21 cm signal.

astro-ph.CO↗

arXiv2025

Improved upper limits on the 21-cm signal power spectrum at $z=17.0$ and $z=20.3$ from an optimal field observed with NenuFAR

We report the deepest upper limits to date on the power spectrum of the 21-cm signal during the Cosmic Dawn (redshifts: $z>15$), using four nights of observations with NenuFAR. The limits are derived from two redshift bins, centred at $z=20.3$ and $z=17.0$, with integration times of 26.1 h and 23.6 h, from observations of an optimal target field chosen to minimise sidelobe leakage from bright sources. Our analysis incorporates improvements to the data processing pipeline, particularly in subtracting strong radio sources in the primary beam sidelobes and mitigating low-level radio frequency interference, yielding a 50-fold reduction in the excess variance compared to a previous analysis of the north celestial pole field. At $z=20.3$, we achieve a best $2\sigma$ upper limit of $\Delta^{2}_{21}<4.6 \times 10^5 \, \textrm{mK}^{2}$ at $k=0.038$ $h\, \mathrm{cMpc}^{-1}$, while at $z=17.0$, the best limit is $\Delta^{2}_{21}<5.0 \times 10^6 \, \textrm{mK}^{2}$ at $k=0.041$ $h\, \mathrm{cMpc}^{-1}$. These are the strongest constraints on the 21-cm power spectrum at the respective redshifts, with the limit at $z = 20.3$ being deeper by more than an order of magnitude over all previous Cosmic Dawn power spectrum limits. Comparison against simulated exotic 21-cm signals shows that while the $z=20.3$ limits begin to exclude the most extreme models predicting signals stronger than the EDGES detection, an order-of-magnitude improvement would constrain signals compatible with EDGES. A coherence analysis reveals that the excess variance is largely incoherent across nights for the $z=20.3$ redshift bin, suggesting that deeper integrations could yield significantly stronger constraints on the 21-cm signal from the Cosmic Dawn.

astro-ph.CO↗

arXiv2025

Constraints on the state of the IGM at $z\sim 8-10$ using redshifted 21-cm observations with LOFAR

The power spectra of the redshifted 21-cm signal from the Epoch of Reionization (EoR) contain information about the ionization and thermal states of the intergalactic medium (IGM), and depend on the properties of the EoR sources. Recently, Mertens et al 2025 has analysed 10 nights of LOFAR high-band data and estimated upper limits on the 21-cm power spectrum at redshifts 8.3, 9.1 and 10.1. Here we use these upper limit results to constrain the properties of the IGM at those redshifts. We focus on the properties of the ionized and heated regions where the temperature is larger than that of the CMB. We model the 21-cm power spectrum with the code GRIZZLY, and use a Bayesian inference framework to explore the source parameters for uniform priors on their ranges. The framework also provides information about the IGM properties in the form of derived parameters. In a model which includes a radio background in excess of the CMB, the 95 (68) per cent credible intervals of disfavoured models at redshift 9.1 for the chosen priors correspond to IGM states with averaged ionization and heated fraction below 0.46 ($\lesssim 0.05$), an average gas temperature below 44 K (4 K), and a characteristic size of the heated region $\lesssim 14 ~h^{-1} ~\mathrm{Mpc}$ ($\lesssim 3 ~h^{-1} ~\mathrm{Mpc}$). The 68 per cent credible interval suggests an excess radio background which is more than 100 per cent of the CMB at 1.42 GHz, while the 95 per cent credible interval of the radio background efficiency parameter spans the entire prior range. The behaviour of the credible intervals is similar at all redshifts. The models disfavoured by the LOFAR upper limits are extreme ones, as they are mainly driven by rare and large ionized or heated regions.

astro-ph.CO↗

arXiv2025

First upper limits on the 21-cm signal power spectrum of neutral hydrogen at $z=9.16$ from the LOFAR 3C196 field

The redshifted 21-cm signal of neutral hydrogen from the Epoch of Reionization (EoR) can potentially be detected using low-frequency radio instruments such as the Low-Frequency Array (LOFAR). So far, LOFAR upper limits on the 21-cm signal power spectrum have been published using a single target field: the North Celestial Pole (NCP). In this work, we analyse and provide upper limits for the 3C196 field, observed by LOFAR, with a strong ${\approx}80\,$Jy source in the centre. This field offers advantages such as higher sensitivity due to zenith-crossing observations and reduced geostationary radio-frequency interference, but also poses challenges due to the presence of the bright central source. After constructing a wide-field sky model, we process a single 6-hour night of 3C196 observations using direction-independent and direction-dependent calibration, followed by a residual foreground subtraction with a machine learned Gaussian process regression (ML-GPR). A bias correction is necessary to account for signal suppression in the GPR step. Still, even after this correction, the upper limits are a factor of two lower than previous single-night NCP results, with a lowest $2\sigma$ upper limit of $(146.61\,\text{mK})^2$ at $z = 9.16$ and $k=0.078\,h\,\text{cMpc}^{-1}$ (with $\text{d}k/k\approx 0.3$). The results also reveal an excess power, different in behaviour from that observed in the NCP field, suggesting a potential residual foreground origin. In future work, the use of multiple nights of 3C196 observations combined with improvements to sky modelling and ML-GPR to avoid the need for bias correction should provide tighter constraints per unit observing time than the NCP.

astro-ph.CO↗

arXiv2025

The impact of diffuse Galactic emission on direction-independent gain calibration in high-redshift 21 cm observations

This study examines the impact of diffuse Galactic emission (DGE) on sky-based direction-independent (DI) gain calibration using realistic forward simulations of Low-Frequency Array (LOFAR) observations of the high-redshift 21 cm signal of neutral hydrogen during the Epoch of Reionization (EoR). We simulated LOFAR observations between 147 and 159 MHz using a sky model that includes a point source catalog and DGE. The simulated observations were DI-gain calibrated with the point source catalog alone, utilizing the LOFAR-EoR data analysis pipeline. A full power spectrum (PS) analysis was conducted to measure the systematic bias, relative to thermal noise, caused by DI-gain calibration using a point-source-only (PSO) sky model, when applied to simulated data that include both point sources and DGE. The results are compared to a ground truth scenario where both the simulated sky and the calibration model include only point sources. Additionally, the cross-coherence between observation pairs was computed to determine whether DI-gain calibration errors are coherent or incoherent in specific regions of PS space as a function of integration time. We find that DI-gain calibration with a PSO sky model that omits DGE introduces a systematic bias in the PS for $k_{\parallel}$ bins < 0.2 $h\,\mathrm{Mpc}^{-1}$. The PS errors in these bins are coherent in time and frequency; therefore, the resulting bias could be mitigated during the foreground removal step using Gaussian Process Regression, as demonstrated in previous studies. In contrast, errors for $k_{\parallel}$ > 0.2 $h\,\mathrm{Mpc}^{-1}$ are largely incoherent and average down as noise. We conclude that, based on our analysis prior to foreground removal, missing DGE in the sky model during DI-gain calibration is unlikely to be a dominant contributor to the excess noise observed in the current LOFAR-EoR upper limits on the 21 cm signal PS.

astro-ph.CO↗

arXiv2025

Robust direction-dependent gain-calibration of beam-modelling errors far from the target field

Many astronomical questions require deep, wide-field observations at low radio frequencies. Phased arrays like LOFAR and SKA-low are designed for this, but have inherently unstable element gains, leading to time, frequency and direction-dependent gain errors. Precise direction-dependent calibration of observations is therefore key to reaching the highest possible dynamic range. Many tools for direction-dependent calibration utilise sky and beam models to infer gains. However, these calibration tools struggle with precision calibration for relatively bright (e.g. A-team) sources far from the beam centre. Therefore, the point-spread-function of these sources can potentially obscure a faint signal of interest. We show that, and why, the assumption of a smooth gain solution per station fails for realistic radio interferometers, and how this affects gain-calibration results. Subsequently, we introduce an improvement for smooth spectral gain constraints for direction-dependent gain-calibration algorithms, in which the level of regularisation is weighted by the expected station response to the sky model. We test this method using direction-dependent calibration method DDECal and physically-motivated beam modelling errors for LOFAR-HBA stations. The new method outperforms the standard method for various calibration settings near nulls in the beam, and matches the standard inverse-variance-weighted method's performance for the remainder of the data. The proposed method is especially effective for short baselines, both in visibility and image space. Improved direction-dependent gain-calibration is critical for future high-precision SKA-low observations, where higher sensitivity, increased antenna beam complexity, and mutual coupling call for better off-axis source subtraction, which may not be achieved through improved beam models alone.

astro-ph.IM↗

arXiv2025

Near-field imaging of local interference in radio interferometric data: Impact on the redshifted 21 cm power spectrum

Radio-frequency interference (RFI) is a major systematic limitation in radio astronomy, particularly for science cases requiring high sensitivity, such as 21 cm cosmology. Traditionally, RFI is dealt with by identifying its signature in the dynamic spectra of visibility data and flagging strongly affected regions. However, for RFI sources that do not occupy narrow regions in the time-frequency space, such as persistent local RFI, modeling these sources could be essential to mitigating their impact. This paper introduces two methods for detecting and characterizing local RFI sources from radio interferometric visibilities: matched filtering and maximum a posteriori (MAP) imaging. These algorithms use the spherical wave equation to construct three-dimensional near-field image cubes of RFI intensity from the visibilities. The matched filter algorithm can generate normalized maps by cross-correlating the expected contributions from RFI sources with the observed visibilities, while the MAP method performs a regularized inversion of the visibility equation in the near field. We developed a full polarization simulation framework for RFI and demonstrated the methods on simulated observations of local RFI sources. The stability, speed, and errors introduced by these algorithms were investigated, and, as a demonstration, the algorithms were applied to a subset of NenuFAR observations to perform spatial, spectral, and temporal characterization of two local RFI sources. We used simulations to assess the impact of local RFI on images, the uv plane, and cylindrical power spectra, and to quantify the level of bias introduced by the algorithms in order to understand their implications for the estimated 21 cm power spectrum with radio interferometers. The near-field imaging and simulation codes are publicly available in the Python library nfis.

astro-ph.IM↗

arXiv2025

Square Kilometre Array Science Data Challenge 3a: foreground removal for an EoR experiment

We present and analyse the results of the Science data challenge 3a (SDC3a, https://sdc3.skao.int/challenges/foregrounds), an EoR foreground-removal community-wide exercise organised by the Square Kilometre Array Observatory (SKAO). The challenge ran for 8 months, from March to October 2023. Participants were provided with realistic simulations of SKA-Low data between 106 MHz and 196 MHz, including foreground contamination from extragalactic as well as Galactic emission, instrumental and systematic effects. They were asked to deliver cylindrical power spectra of the EoR signal, cleaned from all corruptions, and the corresponding confidence levels. Here we describe the approaches taken by the 17 teams that completed the challenge, and we assess their performance using different metrics. The challenge results provide a positive outlook on the capabilities of current foreground-mitigation approaches to recover the faint EoR signal from SKA-Low observations. The median error committed in the EoR power spectrum recovery is below the true signal for seven teams, although in some cases there are some significant outliers. The smallest residual overall is $4.2_{-4.2}^{+20} \times 10^{-4}\,\rm{K}^2h^{-3}$cMpc$^{3}$ across all considered scales and frequencies. The estimation of confidence levels provided by the teams is overall less accurate, with the true error being typically under-estimated, sometimes very significantly. The most accurate error bars account for $60 \pm 20$\% of the true errors committed. The challenge results provide a means for all teams to understand and improve their performance. This challenge indicates that the comparison between independent pipelines could be a powerful tool to assess residual biases and improve error estimation.

astro-ph.IM↗

arXiv2025

Deeper multi-redshift upper limits on the Epoch of Reionization 21-cm signal power spectrum from LOFAR between z=8.3 and z=10.1

We present new upper limits on the 21-cm signal power spectrum from the Epoch of Reionization (EoR), at redshifts $z \approx 10.1, 9.1, \text{ and } 8.3$, based on reprocessed observations from the Low-Frequency Array (LOFAR). The analysis incorporates significant enhancements in calibration methods, sky model subtraction, radio-frequency interference (RFI) mitigation, and an improved signal separation technique using machine learning to develop a physically motivated covariance model for the 21-cm signal. These advancements have markedly reduced previously observed excess power due to residual systematics, bringing the measurements closer to the theoretical thermal noise limit across the entire $k$-space. Using comparable observational data, we achieve a 2 to 4-fold improvement over our previous LOFAR limits, with best upper limits of $\Delta_{21}^2 < (68.7\,\mathrm{mK})^2$ at $k = 0.076\,h\,\mathrm{cMpc}^{-1}$, $\Delta_{21}^2 < (54.3\,\mathrm{mK})^2$ at $k = 0.076\,h\,\mathrm{cMpc}^{-1}$ and $\Delta_{21}^2 < (65.5\,\mathrm{mK})^2$ at $k = 0.083\,h\,\mathrm{cMpc}^{-1}$ at redshifts $z \approx 10.1, 9.1$, and $8.3$, respectively. These new multi-redshift upper limits provide new constraints that can be used to refine our understanding of the astrophysical processes during the EoR. Comprehensive validation tests, including signal injection, were performed to ensure the robustness of our methods. The remaining excess power is attributed to residual foreground emissions from distant sources, beam model inaccuracies, and low-level RFI. We discuss ongoing and future improvements to the data processing pipeline aimed at further reducing these residuals, thereby enhancing the sensitivity of LOFAR observations in the quest to detect the 21-cm signal from the EoR.

astro-ph.CO↗

arXiv2025

Spectral modelling of Cygnus A between 110 and 250 MHz. Impact on the LOFAR 21-cm signal power spectrum

Studying the redshifted 21-cm signal from the the neutral hydrogen during the Epoch of Reionization and Cosmic Dawn is fundamental for understanding the physics of the early universe. One of the challenges that 21-cm experiments face is the contamination by bright foreground sources, such as Cygnus A, for which accurate spatial and spectral models are needed to minimise the residual contamination after their removal. In this work, we develop a new, high-resolution model of Cygnus A using Low Frequency Array (LOFAR) observations in the $110{-}250$ MHz range, improving upon previous models by incorporating physical spectral information through the forced-spectrum method during multi-frequency deconvolution. This approach addresses the limitations of earlier models by providing a more accurate representation of the complex structure and spectral behaviour of Cygnus A, including the spectral turnover in its brightest hotspots. The impact of this new model on the LOFAR 21-cm signal power spectrum is assessed by comparing it with both simulated and observed North Celestial Pole data sets. Significant improvements are observed in the cylindrical power spectrum along the Cygnus A direction, highlighting the importance of having spectrally accurate models of the brightest foreground sources. However, this improvement is washed out in the spherical power spectrum, where we measure differences of a few hundred mK at $k<0.63\,h\,\text{cMpc}^{-1}$, but not statistically significant. The results suggest that other systematic effects must be mitigated before a substantial impact on 21-cm power spectrum can be achieved.

astro-ph.CO↗

arXiv2024

Ionospheric contributions to the excess power in high-redshift 21-cm power-spectrum observations with LOFAR

The turbulent ionosphere causes phase shifts to incoming radio waves on a broad range of temporal and spatial scales. When an interferometer is not sufficiently calibrated for the direction-dependent ionospheric effects, the time-varying phase shifts can cause the signal to decorrelate. The ionosphere's influence over various spatiotemporal scales introduces a baseline-dependent effect on the interferometric array. We study the impact of baseline-dependent decorrelation on high-redshift observations with the Low Frequency Array (LOFAR). Datasets with a range of ionospheric corruptions are simulated using a thin-screen ionosphere model, and calibrated using the state-of-the-art LOFAR Epoch of Reionisation pipeline. For the first time ever, we show the ionospheric impact on various stages of the calibration process including an analysis of the transfer of gain errors from longer to shorter baselines using realistic end-to-end simulations. We find that direction-dependent calibration for source subtraction leaves excess power of up to two orders of magnitude above the thermal noise at the largest spectral scales in the cylindrically averaged auto-power spectrum under normal ionospheric conditions. However, we demonstrate that this excess power can be removed through Gaussian process regression, leaving no excess power above the ten per cent level for a $5~$km diffractive scale. We conclude that ionospheric errors, in the absence of interactions with other aggravating effects, do not constitute a dominant component in the excess power observed in LOFAR Epoch of Reionisation observations of the North Celestial Pole. Future work should therefore focus on less spectrally smooth effects, such as beam modelling errors.

astro-ph.CO↗

arXiv2024

The impact of lossy data compression on the power spectrum of the high redshift 21-cm signal with LOFAR

Current radio interferometers output multi-petabyte-scale volumes of data per year making the storage, transfer, and processing of this data a sizeable challenge. This challenge is expected to grow with the next-generation telescopes such as the Square Kilometre Array. Lossy compression of interferometric data post-correlation can abate this challenge. However, since high-redshift 21-cm studies impose strict precision requirements, the impact of such lossy data compression on the 21-cm signal power spectrum statistic should be understood. We apply Dysco visibility compression, a technique to normalize and quantize specifically designed for radio interferometric data. We establish the level of the compression noise in the power spectrum in comparison to the thermal noise as well as its coherency behavior. Finally, for optimal compression results, we compare the compression noise obtained from different compression settings to a nominal 21-cm signal power. From a single night of observation, we find that the noise introduced due to the compression is more than five orders of magnitude lower than the thermal noise level in the power spectrum. The noise does not affect calibration. The compression noise shows no correlation with the sky signal and has no measurable coherent component. The level of compression error in the power spectrum ultimately depends on the compression settings. Dysco visibility compression is found to be of insignificant concern for 21-cm power spectrum studies. Hence, data volumes can be safely reduced by factors of $\sim 4$ and with insignificant bias to the final power spectrum. Data from SKA-low will likely be compressible by the same factor as LOFAR, owing to the similarities of the two instruments. The same technique can be used to compress data from other telescopes, but a small adjustment of the compression parameters might be required.

astro-ph.CO↗

arXiv2024

Beyond the horizon: Quantifying the full sky foreground wedge in the cylindrical power spectrum

One of the main obstacles preventing the detection of the redshifted 21-cm signal from neutral hydrogen in the early Universe is the astrophysical foreground emission, which is several orders of magnitude brighter than the signal. The foregrounds, due to their smooth spectra, are expected to predominantly occupy a region in the cylindrical power spectrum known as the foreground wedge. However, the conventional equations describing the extent of the foreground wedge are derived under a flat-sky approximation. This assumption breaks down for tracking wide-field instruments, thus rendering these equations inapplicable in these situations. In this paper, we derive equations for the full sky foreground wedge and show that the foregrounds can potentially extend far beyond what the conventional equations suggest. We also derive the equations that describe a specific bright source in the cylindrical power spectrum space. The validity of both sets of equations is tested against numerical simulations. Many current and upcoming interferometers (e.g., LOFAR, NenuFAR, MWA, SKA) are wide-field phase-tracking instruments. These equations give us new insights into the nature of foreground contamination in the cylindrical power spectra estimated using wide-field instruments. Additionally, they allow us to accurately associate features in the power spectrum to foregrounds or instrumental effects. The equations are also important for correctly selecting the "EoR window" for foreground avoidance analyses, and for planning 21-cm observations. In future analyses, it is recommended to use these updated horizon lines to indicate the foreground wedge in the cylindrical power spectrum accurately. The new equations for generating the updated wedge lines are made available in a Python library, pslines.

astro-ph.CO↗

arXiv2023

First upper limits on the 21 cm signal power spectrum from cosmic dawn from one night of observations with NenuFAR

The redshifted 21 cm signal from neutral hydrogen is a direct probe of the physics of the early universe and has been an important science driver of many present and upcoming radio interferometers. In this study we use a single night of observations with the New Extension in Nan\c{c}ay Upgrading LOFAR (NenuFAR) to place upper limits on the 21 cm power spectrum from cosmic dawn at a redshift of $z$ = 20.3. NenuFAR is a new low-frequency radio interferometer, operating in the 10-85 MHz frequency range, currently under construction at the Nan\c{c}ay Radio Observatory in France. It is a phased array instrument with a very dense uv coverage at short baselines, making it one of the most sensitive instruments for 21 cm cosmology analyses at these frequencies. Our analysis adopts the foreground subtraction approach, in which sky sources are modeled and subtracted through calibration and residual foregrounds are subsequently removed using Gaussian process regression. The final power spectra are constructed from the gridded residual data cubes in the uv plane. Signal injection tests are performed at each step of the analysis pipeline, the relevant pipeline settings are optimized to ensure minimal signal loss, and any signal suppression is accounted for through a bias correction on our final upper limits. We obtain a best 2$\sigma$ upper limit of $2.4\times 10^7$ $\text{mK}^{2}$ at $z$ = 20.3 and $k$ = 0.041 $h\,\text{cMpc}^{-1}$. We see a strong excess power in the data, making our upper limits two orders of magnitude higher than the thermal noise limit. We investigate the origin and nature of this excess power and discuss further improvements to the analysis pipeline that can potentially mitigate it and consequently allow us to reach thermal noise sensitivity when multiple nights of observations are processed in the future.

astro-ph.CO↗

arXiv2023

Transient RFI environment of LOFAR-LBA at 72-75 MHz: Impact on ultra-widefield AARTFAAC Cosmic Explorer observations of the redshifted 21-cm signal

Measurement of the redshifted 21-cm signal of neutral hydrogen from the Cosmic Dawn (CD) and Epoch of Reionisation (EoR) promises to unveil a wealth of information about the astrophysical processes during the first billion years of evolution of the universe. The AARTFAAC Cosmic Explorer (ACE) utilises the AARTFAAC wide-field imager of LOFAR to measure the power spectrum of the intensity fluctuations of the redshifted 21-cm signal from the CD at z~18. The RFI from various sources contaminates the observed data and it is crucial to exclude the RFI-affected data in the analysis for reliable detection. In this work, we investigate the impact of non-ground-based transient RFI using cross-power spectra and cross-coherence metrics to assess the correlation of RFI over time and investigate the level of impact of transient RFI on the ACE 21-cm power spectrum estimation. We detected moving sky-based transient RFI sources that cross the field of view within a few minutes and appear to be mainly from aeroplane communication beacons at the location of the LOFAR core in the 72-75 MHz band, by inspecting filtered images. This transient RFI is mostly uncorrelated over time and is only expected to dominate over the thermal noise for an extremely deep integration time of 3000 hours or more with a hypothetical instrument that is sky temperature dominated at 75 MHz. We find no visible correlation over different k-modes in Fourier space in the presence of noise for realistic thermal noise scenarios. We conclude that the sky-based transient RFI from aeroplanes, satellites and meteorites at present does not pose a significant concern for the ACE analyses at the current level of sensitivity and after integrating over the available 500 hours of observed data. However, it is crucial to mitigate or filter such transient RFI for more sensitive experiments aiming for significantly deeper integration.

astro-ph.CO↗

arXiv2023

A novel radio imaging method for physical spectral index modelling

We present a new method, called "forced-spectrum fitting", for physically-based spectral modelling of radio sources during deconvolution. This improves upon current common deconvolution fitting methods, which often produce inaccurate spectra. Our method uses any pre-existing spectral index map to assign spectral indices to each model component cleaned during the multi-frequency deconvolution of WSClean, where the pre-determined spectrum is fitted. The component magnitude is evaluated by performing a modified weighted linear least-squares fit. We test this method on a simulated LOFAR-HBA observation of the 3C196 QSO and a real LOFAR-HBA observation of the 4C+55.16 FRI galaxy. We compare the results from the forced-spectrum fitting with traditional joined-channel deconvolution using polynomial fitting. Because no prior spectral information was available for 4C+55.16, we demonstrate a method for extracting spectral indices in the observed frequency band using "clustering". The models generated by the forced-spectrum fitting are used to improve the calibration of the datasets. The final residuals are comparable to existing multi-frequency deconvolution methods, but the output model agrees with the provided spectral index map, embedding correct spectral information. While forced-spectrum fitting does not solve the determination of the spectral information itself, it enables the construction of accurate multi-frequency models that can be used for wide-band calibration and subtraction.

astro-ph.IM↗

arXiv2022

Assessing the impact of two independent direction-dependent calibration algorithms on the LOFAR 21-cm signal power spectrum

Detecting the 21-cm signal from the Epoch of Reionisation (EoR) is challenging due to the strong astrophysical foregrounds, ionospheric effects, radio frequency interference and instrumental effects. Understanding and calibrating these effects are crucial for the detection. In this work, we introduce a newly developed direction-dependent (DD) calibration algorithm DDECAL and compare its performance with an existing algorithm, SAGECAL, in the context of the LOFAR-EoR 21-cm power spectrum experiment. In our data set, the North Celestial Pole (NCP) and its flanking fields were observed simultaneously. We analyse the NCP and one of its flanking fields. The NCP field is calibrated by the standard pipeline, using SAGECAL with an extensive sky model and 122 directions, and the flanking field is calibrated by DDECAL and SAGECAL with a simpler sky model and 22 directions. Additionally, two strategies are used for subtracting Cassiopeia A and Cygnus A. The results show that DDECAL performs better at subtracting sources in the primary beam region due to the application of a beam model, while SAGECAL performs better at subtracting Cassiopeia A and Cygnus A. This indicates that including a beam model during DD calibration significantly improves the performance. The benefit is obvious in the primary beam region. We also compare the 21-cm power spectra on two different fields. The results show that the flanking field produces better upper limits compared to the NCP in this particular observation. Despite the minor differences between DDECAL and SAGECAL due to the beam application, we find that the two algorithms yield comparable 21-cm power spectra on the LOFAR-EoR data after foreground removal. Hence, the current LOFAR-EoR 21-cm power spectrum limits are not likely to depend on the DD calibration method.

astro-ph.CO↗