arXiv subjects

E. Romano

Publications and source records attributed to E. Romano.

6 recordsLinked to original sources

arXiv2024

New generation B-Field and RAD-tolerant DCDC power converter for on-detector operation

The increase in the number of readout channels in new detectors, like the Micro Pattern Gas Detectors (MPGD), in the order of several millions, requires a large amount of electrical power to supply the front-end electronics, up to hundreds kW. If this power is generated at long distances from the detector, the voltage drop on the connection cables puts serious constraints to the supply current, to the wire cross-section and to the power distribution. A large amount of voltage drop on the cables, apart an increased power dissipation on wire resistance, determines regulation issues on the load in case of current transients. To mitigate these problems, a new generation DC/DC converter, working in a heavily hostile environment and with a power density greater than 200 W/dm3, was developed. It is modular, with up to four independent modules, eight channels each, collected in a water-cooled crate, and can supply the load with an adjustable 10 to 12 V output up to 170 W per channel. In this contribution, the design constraints of such a converter are analysed, taking as a basis the environmental, electrical and mechanical requirements of the ATLAS New Small Wheel (NSW) project. Thermal considerations require the converter to be water-cooled, and the dimensional constraints impose the adoption of an innovative design to convey the dissipated heat towards the heat exchanger. The control and monitoring system allows for the full remote management of the converter. Main electrical parameters were measured and are reported. The converter was also characterized in a harsh working environment, with radiation tests in the CERN CHARM facility beyond the limits estimated for ten years operation in ATLAS, and with magnetic field tests in various orientations, using different magnets at CERN up to 1.3 T.

physics.ins-det↗

arXiv2020

Cooling and Timing tests of the ATLAS Fast Tracker VME boards

The Fast Tracker (FTK) is an ATLAS trigger upgrade built for full event, low-latency, high-rate tracking. The FTK core, made of 9U VME boards, performs the most demanding computational task. The Associative Memory Board Serial Link Processor (AMB) and the Auxiliary card (AUX), plugged on the front and back sides of the same VME slot, constitute the Processing Unit (PU), which finds tracks using hits from 8 layers of the inner detector. The PU works in pipeline with the Second Stage Board (SSB), which finds 12-layer tracks by adding extra hits to the identified tracks. In the designed configuration, 16 PUs and 4 SSBs are installed in a VME crate. The high power-consumption of the AMB, AUX and SSB (respectively of about 250 W, 70 W and 160 W per board) required the development of a custom cooling system. Even though the expected power consumption for each VME crate of the FTK system is high compared to a common VME setup, the 8 FTK core crates will use $\approx$ 60 kW, which is just a fraction of the power and the space needed for a CPU farm performing the same task. We report on the integration of 32 PUs and 8 SSBs inside the FTK system, on the infrastructures needed to run and cool them, and on the tests performed to verify the system processing rate and the temperature stability at a safe value.

physics.ins-det↗

arXiv2020

A comparison between scintillation light Analog and Digital trigger for large volume Liquid Argon Time Projection Chambers

Large volume Liquid Argon Time Projection Chambers (LAr-TPC) are used and proposed for neutrino physics and rare event search. Most of these detectors make use of the scintillation light of liquid argon for trigger purposes. Two different approaches can be adopted to provide these detectors with an effective trigger system, relying upon analog or digital processing of signal coming from photodetectors, like photomultiplier tubes or silicon photomultipliers. Each method presents advantages and drawbacks, so the implementation of a hybrid solution can benefit from both approaches. To this purpose, an innovative electronic board prototype has been designed and proposed for the use in large volume LAr-TPC detectors.

physics.ins-det↗

arXiv2018

Construction techniques and performances of a full-size prototype Micromegas chamber for the ATLAS muon spectrometer upgrade

A full-size prototype of a Micromegas precision tracking chamber for the upgrade of the ATLAS detector at the LHC Collider has been built between October 2015 and April 2016. This paper describes in detail the procedures used in constructing the single modules of the chamber in various INFN laboratories and the final assembly at the Laboratori Nazionali di Frascati (LNF). Results of the chamber exposure to the CERN SPS/H8 beam line in June 2016 are also presented. The performances achieved in the construction and the results of the test beam are compared with the requirements, which are imposed by the severe environment during the data-taking of the LHC foreseen for the next years.

physics.ins-det↗

arXiv2011

On the exponent of a finite group admitting a fixed-point-free four-group of automorphisms

Let $A$ be a group isomorphic with either $S_4$, the symmetric group on four symbols, or $D_8$, the dihedral group of order 8. Let $V$ be a normal four-subgroup of $A$ and $α$ an involution in $A\setminus V$. Suppose that $A$ acts on a finite group $G$ in such a manner that $C_G(V)=1$ and $C_G(α)$ has exponent $e$. We show that if $A\cong S_4$ then the exponent of $G$ is $e$-bounded and if $A\cong D_8$ then the exponent of the derived group $G'$ is $e$-bounded. This work was motivated by recent results on the exponent of a finite group admitting an action by a Frobenius group of automorphisms.

math.GR↗

arXiv2010

Industrially Scalable Process for Silicon Nanowires for Seebeck Generators

The observation that the thermal conductivity of single-crystalline silicon nanowires with diameter on the length scale of 25 nm is lower than that of bulk material by two orders of magnitude has attracted the interest onto silicon as a potentially effective thermoelectric material. However, the potential interest has a hope of transforming in a practical interest only if poly-crystalline silicon can replace single crystalline silicon and the preparation of nanowires does not involve any advanced photolithography. In this work we show that a technique, based on the controlled etching and filling of recessed regions and employing standard photolithography and deposition-etching methods, succeeds in the preparation of poly-crystalline silicon nanowires (with diameter of 25 nm and length on the centimetre scale) at a linear density of 3E6 cm^-1.

cond-mat.mtrl-sci↗