arXiv subjects

Edmund Tarleton

Publications and source records attributed to Edmund Tarleton.

22 records · Page 2Linked to original sources

arXiv2019

Orientation-dependent indentation response of helium-implanted tungsten

A literature review of studies investigating the topography of nano-indents in ion-implanted materials reveals seemingly inconsistent observations, with report of both pile-up and sink-in. This may be due to the crystallographic orientation of the measured sample point, which is often not considered when evaluating implantation-induced changes in the deformation response. Here we explore the orientation dependence of spherical nano-indentation in pure and helium-implanted tungsten, considering grains with <001>, <110> and <111> out-of-plane orientations. Atomic force microscopy (AFM) of indents in unimplanted tungsten shows little orientation dependence. However, in the implanted material a much larger, more localised pile-up is observed for <001> grains than for <110> and <111> orientations. Based on the observations for <001> grains, we hypothesise that a large initial hardening due to helium-induced defects is followed by localised defect removal and subsequent strain softening. A crystal plasticity finite element model of the indentation process, formulated based on this hypothesis, accurately reproduces the experimentally-observed orientation-dependence of indent morphology. The results suggest that the mechanism governing the interaction of helium-induced defects with glide dislocations is orientation independent. Rather, differences in pile-up morphology are due to the relative orientations of the crystal slip systems, sample surface and spherical indenter. This highlights the importance of accounting for crystallographic orientation when probing the deformation behaviour of ion-implanted materials using nano-indentation.

physics.app-ph↗

arXiv2018

Discrete dislocation plasticity HELPs understand hydrogen effects in bcc materials

In an attempt to bridge the gap between atomistic and continuum plasticity simulations of hydrogen in iron, we present three dimensional discrete dislocation plasticity simulations incorporating the hydrogen elastic stress and a hydrogen dependent dislocation mobility law. The hydrogen induced stress is incorporated following the formulation derived by Gu and El-Awady (2018) which here we extend to a finite boundary value problem, a microcantilever beam, via the superposition principle. The hydrogen dependent mobility law is based on first principle calculations by Katzarov et al. (2017) and was found to promote dislocation generation and enhance slip planarity at a bulk hydrogen concentration of 0.1 appm; which is typical for bcc materials. The hydrogen elastic stress produced the same behaviour, but only when the bulk concentration was extremely high. In a microcantilever, hydrogen was found to promote dislocation activity which lowered the flow stress and generated more pronounced slip steps on the free surfaces. These observations are consistent with the hydrogen enhanced localized plasticity (HELP) mechanism, and it is concluded that both the hydrogen elastic stress and hydrogen increased dislocation mobility are viable explanations for HELP. However it is the latter that dominates at the low concentrations typically found in bcc metals.

cond-mat.mtrl-sci↗

arXiv2018

Consistent determination of geometrically necessary dislocation density from simulations and experiments

The use of Nye's dislocation tensor for calculating the density of geometrically necessary dislocations (GND) is widely adopted in the study of plastically deformed materials. The curl operation involved in finding the Nye tensor, while conceptually straightforward has been marred with inconsistencies and several different definitions are in use. For the three most common definitions, we show that their consistent application leads to the same result. To eliminate frequently encountered confusion, a summary of expressions for Nye's tensor in terms of elastic and plastic deformation gradient, and for both small and large deformations, is presented. A further question when estimating GND density concerns the optimization technique used to solve the under-determined set of equations linking Nye's tensor and GND density. A systematic comparison of the densities obtained by two widely used techniques, L1 and L2 minimisation, shows that both methods yield remarkably similar total GND densities. Thus the mathematically simpler, L2, may be preferred over L1 except when information about the distribution of densities on specific slip systems is required. To illustrate this, we compare experimentally measured lattice distortions beneath nano-indents in pure tungsten, probed using 3D-resolved synchrotron X-ray micro-diffraction, with those predicted by 3D strain-gradient crystal plasticity finite element calculations. The results are in good agreement and show that the volumetric component of the elastic strain field has a surprisingly small effect on the determined Nye tensor. This is important for experimental techniques, such as micro-beam Laue measurements and HR-EBSD, where only the deviatoric strain component is measured.

cond-mat.mtrl-sci↗

arXiv2016

Coherent X-ray measurements of ion-implantation-induced lattice strains in nano-crystals

Focussed Ion Beam (FIB) milling is a mainstay of nano-scale machining. By manipulating a tightly focussed beam of energetic ions, often gallium (Ga+), FIB can sculpt nanostructures via localised sputtering. This ability to cut solid matter on the nano-scale has revolutionised sample preparation across the life-, earth- and materials sciences. For example FIB is central to microchip prototyping, 3D material analysis, targeted electron microscopy sample extraction and the nanotechnology behind size-dependent material properties. Despite its widespread usage, detailed understanding of the functional consequences of FIB-induced structural damage, intrinsic to the technique, remains elusive. Here, we present nano-scale measurements of three-dimensional, FIB-induced lattice strains, probed using Bragg Coherent X-ray Diffraction Imaging (BCDI). We observe that even low gallium ion doses, typical of FIB imaging, cause substantial lattice distortions. At higher doses, extended self-organised defect structures appear, giving rise to stresses far in excess of the bulk yield limit. Combined with detailed numerical calculations, these observations provide fundamental insight into the nature of the damage created and the structural instabilities that lead to a surprisingly inhomogeneous morphology.

cond-mat.mtrl-sci↗