arXiv subjects

Elliott J. Rouse

Publications and source records attributed to Elliott J. Rouse.

5 recordsLinked to original sources

arXiv2026

Design and Characterization of a Limb Encircling Actuator

Lower-limb powered exoskeletons have demonstrated substantial improvements in mobility and function, but most designs place actuation components lateral to the legs or remotely at the waist or back. These configurations often extend beyond the body's natural envelope, making devices intrusive in everyday use and potentially limiting societal adoption. We posit that rethinking actuation geometry could enable exoskeletons that conform more closely to the body. Here, we explored an actuation layout in which the actuator encircles the limb in a plane orthogonal to the limb axis, potentially reducing its spatial footprint around the body. We developed the Limb-Encircling Actuator (LEA) and characterized its electromechanical properties using a custom-built testbed. The LEA also features a novel radial bearing layout with potential as a lightweight or lower-cost alternative to traditional large-diameter bearings. The actuator achieved a continuous torque density of 7.5 Nm/kg with a mass of 894 g. Despite this high torque density and innovative layout, the system remained difficult to contain close to the body. These results highlight opportunities and challenges in limb-encircling actuation and provide insights into torque-dense exoskeleton designs that could integrate more readily into everyday apparel if challenges in actuator sizing and geometry are overcome.

cs.RO↗

arXiv2022

Real-Time Gait Phase and Task Estimation for Controlling a Powered Ankle Exoskeleton on Extremely Uneven Terrain

Positive biomechanical outcomes have been reported with lower-limb exoskeletons in laboratory settings, but these devices have difficulty delivering appropriate assistance in synchrony with human gait as the task or rate of phase progression change in real-world environments. This paper presents a controller for an ankle exoskeleton that uses a data-driven kinematic model to continuously estimate the phase, phase rate, stride length, and ground incline states during locomotion, which enables the real-time adaptation of torque assistance to match human torques observed in a multi-activity database of 10 able-bodied subjects. We demonstrate in live experiments with a new cohort of 10 able-bodied participants that the controller yields phase estimates comparable to the state of the art, while also estimating task variables with similar accuracy to recent machine learning approaches. The implemented controller successfully adapts its assistance in response to changing phase and task variables, both during controlled treadmill trials (N=10, phase RMSE: 4.8 +- 2.4\%) and a real-world stress test with extremely uneven terrain (N=1, phase RMSE: 4.8 +- 2.7\%).

cs.RO↗

arXiv2022

Alternative Metrics to Select Motors for Quasi-Direct Drive Actuators

Robotic systems for legged locomotion -- including legged robots, exoskeletons, and prosthetics -- require actuators with low inertia and high output torque. Traditionally, motors have been selected for these applications by maximizing the motor gap radius. We present alternative metrics for motor selection that are invariant to transmission ratio. The proposed metrics reward minimizing the motor inertia while maximizing the torque and motor constants without special consideration for gap radius, providing a better balance of properties for legged locomotion applications. We rigorously characterize the T-Motor RI50 and demonstrate the use of the metrics by comparing the RI50 to the widely-used T-Motor U8 as a case study.

cs.RO↗

arXiv2022

Design and Characterization of 3D Printed, Open-Source Actuators for Legged Locomotion

Impressive animal locomotion capabilities are mediated by the co-evolution of the skeletal morphology and muscular properties. Legged robot performance would also likely benefit from the co-optimization of actuators and leg morphology. However, development of custom actuators for legged robots is often expensive and time consuming, which discourages roboticists from pursuing performance gains afforded by application-specific actuator optimization. This paper presents open-source designs for two quasi-direct-drive actuators with performance regimes appropriate for an 8--15 kg robot, built completely with off the shelf and 3D-printed components for less than $200 USD each. The mechanical, electrical, and thermal properties of each actuator are characterized and compared to benchmark data. Actuators subjected to 420k strides of gait data experienced only a 2% reduction in efficiency and 26 mrad in backlash growth, demonstrating viability for rigorous and sustained research applications. We present a thermal solution that nearly doubles the thermally-driven torque limits of our plastic actuator design. The performance results are comparable to traditional metallic actuators for use in high-speed legged robots of the same scale. These 3D printed designs demonstrate an approach for designing and characterizing low-cost, highly customizable, and highly reproducible actuators, democratizing the field of actuator design and enabling co-design and optimization of actuators and robot legs.

cs.RO↗

arXiv2021

Enhancing Voluntary Motion with Modular, Backdrivable, Powered Hip and Knee Orthoses

Mobility disabilities are prominent in society with wide-ranging detriments to affected individuals. Addressing the specific deficits of individuals within this heterogeneous population requires modular, partial-assist, lower-limb exoskeletons. This paper introduces the Modular Backdrivable Lower-limb Unloading Exoskeleton (M-BLUE), which implements high torque, low mechanical impedance actuators on commercial orthoses with sheet metal modifications to produce a variety of hip- and/or knee-assisting configurations. Benchtop system identification verifies the desirable backdrive properties of the actuator, and allows for torque prediction within 0.4 Nm. An able-bodied human subject experiment demonstrates that three unilateral configurations of M-BLUE (hip only, knee only, and hip-knee) with a simple gravity compensation controller can reduce muscle EMG readings in a lifting and lowering task relative to the bare condition. Reductions in mean muscular effort and peak muscle activation were seen across the primary squat musculature (excluding biceps femoris), demonstrating the potential to reduce fatigue leading to poor lifting posture. These promising results motivate applications of M-BLUE to additional subject populations such as hip/knee osteoarthritis and geriatric frailty, and the expansion of M-BLUE to bilateral and ankle configurations.

cs.RO↗